Transparent Finished, Opaque Finished and Plastic Laminate Cabinets Fabricated with Duraflake FR®Core Material. / WEYERHAEUSER
PO Box 428
Albany, OR 97321
Voice: (541) 928-3341
Fax: (503) 928-4116
Website:
This section uses standards established by the Woodwork Institute of California (WIC) A comparable section using standards of theAmerican Woodwork Institute (AWI) is also available.
Section 06410
Custom Cabinets
GENERAL NOTES TO SPECIFIER:THIS SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE PREPARATION OF PROJECT OR OFFICE MASTER SPECIFICATIONS. IT FOLLOWS GUIDELINES ESTABLISHED BY THE CONSTRUCTION SPECIFICATIONS INSTITUTE, AND THEREFORE MAY BE USED WITH MOST MASTER SPECIFICATION SYSTEMS WITH MINOR EDITING.
EDIT CAREFULLY TO SUIT PROJECT REQUIREMENTS. MODIFY AS NECESSARY AND DELETE ITEMS THAT ARE NOT APPLICABLE. VERIFY THAT REFERENCED SECTION NUMBERS AND TITLES ARE CORRECT. (NUMBERS AND TITLES REFERENCED ARE BASED ON MASTERFORMAT, 1995 EDITION).
THIS SECTION ASSUMES THE PROJECT MANUAL WILL CONTAIN COMPLETE DIVISION 1 DOCUMENTS INCLUDING SECTIONS 01330SUBMITTAL PROCEDURES, 01620PRODUCT OPTIONS, 01630PRODUCT SUBSTITUTION PROCEDURES, 01660PRODUCT STORAGE AND HANDLING REQUIREMENTS, 01740cLEANING, 01770CLOSEOUT PROCEDURES, AND 01780CLOSEOUT SUBMITTALS. CLOSE COORDINATION WITH DIVISION 1 SECTIONS IS REQUIRED. IF THE PROJECT MANUAL DOES NOT CONTAIN THESE SECTIONS, ADDITIONAL INFORMATION SHOULD BE INCLUDED UNDER THE APPROPRIATE ARTICLES.
THIS IS AN OPEN PROPRIETARY SPECIFICATION ALLOWING USERS THE OPTION OF APPROVING OTHER MANUFACTURERS THAT COMPLY WITH THE CRITERIA SPECIFIED HEREIN.
NOTES TO THE SPECIFIER ARE CONTAINED IN BOXES AND SHOULD BE DELETED FROM FINAL COPY.
OPTIONAL ITEMS REQUIRING SELECTION BY THE SPECIFIER ARE ENCLOSED WITHIN BRACKETS, E.G. [35] [40] [45]. MAKE APPROPRIATE SELECTIONS AND DELETE OTHERS.
ITEMS REQUIRING ADDITIONAL INFORMATION ARE UNDERLINED BLANK SPACES, E.G. ______.
OPTIONAL PARAGRAPHS REQUIRING SELECTION OF ONE OF THE OPTIONS ARE SEPARATED BY “OR” WITHIN A BOX, E.G.
OR
OPTIONAL PARAGRAPHS AND FEATURES THAT MAY BE SELECTED OR DELETED AS DESIRED ARE SHOWN IN BOLD FACE TYPE. DELETE BOLD FACE TYPE WHEN RETAINING THESE PARAGRAPHS OR FEATURES.
Part 1 -General
1.01Summary
A.Section Includes:
1.Transparent fininshed wood vneer cabinets including hardware, glass and finishing.
2.Opaque finished wood cabinets including hardware, glass and finishing.
3.Plastic laminate clad wood cabinets including hardware and glass.
B.Related Sections:
1.06415Fire Rated Countertops.
2.Moisture-Resistant Countertops.
INCLUDE APPROPRIATE LANGUAGE BELOW IF WORK SPECIFIED IN THIS SECTION IS TO BE BID AS AN ALTERNATE. OTHERWISE DELETE FOLLOWING PARAGRAPH.
C.Alternates:
1.Reference Section 01230Alternates.
1.02Submittals
A.Reference Section 01330Submittal Procedures; submit following items:
1.Product Data:
a.Plastic laminate surface material; include chips of actual material showing full range of color, pattern and texture.
b.Fire-rated particleboard.
c.Hardware.
d.Finish materials.
e.Installation materials.
2.Shop Drawings: Comply with WIC Section 1.
a.Show dimensioned plans and elevations, large-scale details, materials, assembly methods, joint details, hardware, finishes and means of attachment including required blocking.
b.Show location of accessory items and plumbing and electrical components installed in or on countertops.
c.Provide WIC Certified Compliance Label on first page drawings.
3.Samples following initial color selection:
a.Lumber: 4 inch (100 mm) wide by 12 inch (300 mm) long piece of each species and cut specified; one half natural and one half finished as specified.
RETAIN FOLLOWING SUBPARAGRAPH TO SELECT VENEER FLITCHES AFTER AWARD OF CONTRACT TO WOODWORKER; DELETE IF VENEER FLITCHES ARE PRE-SELECTED. COORDINATE WITH 2.01 B.
b.Minimum of three representative veneer flitch samples, (flitch numbered sets) for each species and cut for use in this Project.
c.High-Pressure Decorative Laminate: 8 by 10 inch (200 by 250 mm) sample of each color, pattern and texture selected.
d.Substrate: 12 by 12 inch (300 by 300 mm) piece of particleboard.
e.Hardware: Sample of each type of hardware visible on exposed surfaces in the finish specified.
4.Quality Assurance/Control Submittals:
a.Qualifications: Proof of fabricator/installer qualifications.
b.Chemical treatment manufacturer's instructions for installing fire-retardant treated wood products.
B.Closeout Submittals: Reference Section 01780Closeout Submittals; submit following items:
INCLUDE ABOVE PARAGRAPH AND FOLLOWING CERTIFICATE ONLY IF CERTIFICATE IS SPECIFIED BELOW UNDER THE QUALITY ASSURANCE ARTICLE.
1.WIC compliance certificate as specified in Quality Assurance article below.
1.03Quality Assurance
A.Overall Standards:
1.Perform Work in accordance with the WIC "Manual of Millwork" except as modified herein.
2.Provide [WIC Certified Compliance Certificate] [WIC Monitored Compliance Certificate] indicating that cabinets comply with requirements of grades specified.
ADVANCED REGISTRATION OF A PROJECT WITH WIC IS REQUIRED FOR THE MONITORED COMPLIANCE PROGRAM AND IS THE RESPONSIBILITY OF THE DESIGN PROFESSIONAL. A REGISTRATION FROM IS IN INCLUDED IN THE MANUAL OF MILLWORK. REGISTRATION FORMS CAN ALSO BE OBTAINED ON-LINE AT OR BY CALLING THE WIC ADMINISTRATIVE OFFICE AT (916) 372-9943.
INSERT REGISTRATION NUMBER IN THE BLANK BELOW UPON RECEIPT OF REGISTRATION ACKNOWLEDGEMENT.
a.Quality Program Registration Number: ______.
b.Quality Program labels/certificate shall be issued prior to [Substantial Completion] [final acceptance by Owner].
B.Qualifications:
1.Fabricator Qualifications: Member, WIC or minimum five years experience in producing cabinets of the type specified.
2.Installer Qualifications: Member, WIC or minimum five years experience in installation of cabinets similar in material and design to that of this Project.
1.04Delivery, Storage, and Handling
A.Reference Section 01660Product Storage and Handling Requirements.
B.Do not deliver cabinets until HVAC system is operating.
1.05Project Conditions
A.Environmental Requirements: Operate HVAC system to maintain occupancy level temperature and relative humidity conditions from 24 hours prior to delivery of cabinets through remainder of construction period.
Part 2 -Products
2.01Materials
INSERT REQUIRED SPECIES AND SELECT TYPE OF CUT IN PARAGRAPHS A. AND B. BELOW. WIC GRADE RULES APPLY TO A LIMITED NUMBER OF SPECIES. IF SPECIES SELECTED IS NOT COVERED BY WIC, CONSIDER SPECIFYING ADDITIONAL GRADING REQUIREMENTS. AND/OR SPECIFIC SOURCES FOR THE MATERIAL. SPECIFIER SHOULD ALSO CAREFULLY REVIEW WIC INFORMATION ON MATCHING (SPECIFIED IN ARTICLE 2.02) AND THE VISUAL EFFECTS PRODUCED BY SPECIFIC SPECIES, CUTS AND FINISHES.
RETAIN FIRE-RETARDANT TREATMENT FOR HARDWOOD LUMBER AS REQUIRED BY LOCAL CODE.
A.Lumber - Transparent Finished Cabinets: ______, [plain sawn] [quarter sawn] [rift sawn].
1.Fire-Retardant Treated by Pressure Process: Comply with AWPA C20.
a.Label: UL Class [I] [II].
SELECT FIRST PARAGRAPH “B” BELOW IF VENEER FLITCHES ARE NOT PRE-SELECTED. SELECT SECOND PARAGRAPH “B” FOR PRE-SELECTED FLITCHES.
B.Face Veneer - Transparent Finished Cabinets:
1.Species: ______.
2.Cut: [Rotary cut] [Plain sliced] [Quarter sliced] [Rift cut], minimum 1/40 inch (0.64 mm) thick.
OR
B.Face Veneer - Transparent Finished Cabinets: Pre-selected flitch.
1.Supplier: ______.
Phone: ______.
Fax: ______.
E-mail: ______.
2.Flitch Number(s): ______.
3.Species: ______.
4.Gross Square Footage (Square Meters) Required: ______SF ( ______m2 ).
C.Lumber and Face Veneer Species - Opaque Finished Cabinets: Any close grained hardwood.
D.High-Pressure Decorative Laminate:
1.Surface: [NEMA LD 3] [As specified in Section 06065].
2.Backing Sheet: [NEMA LD 3] [As specified in Section 06065].
E.Core Material - [Transparent Finished,] [Opaque Finished,] [and] [Plastic Laminate Clad Cabinets]: Fire-Retardant Particleboard:
1.Label: UL Class I.
2.Surface Burning Characteristics - UL 723:
a.Flame Spread: 20 or less.
b.Smoked Developed: 25 or less.
3.Physical Properties - ASTM D 1037 except as noted:
3/8 - 3/4 inch13/16 - 1-1/4 inch
(9.5-19.0 mm)(20.6-31.8 mm)
a.Density - pcf (kg/m3)45.0 (720)44.0 (704)
b.Modulus of Rupture - psi (N/m2)1,600 (11)1,300 (9)
c.Modulus of Elasticity - psi (N/m2)300,000 (2 100)250,000 (1 700)
d.Internal Bond - psi (N/m2)80 (0.55)60 (0.40)
e.Screw Holding Capacity
Face - lbs (N)250 (1 100)250 (1 100)
Edge - lbs (N)225 (1 000)175 (780)
f.Thickness Tolerance - inches (mm)±0.005 (±0.2)±0.005 (±0.2)
WARNING: PARTICLEBOARD IS MANUFACTURED WITH UREA FORMALDEHYDE RESIN AND MAY RELEASE FORMALDEHYDE IN LOW CONCENTRATIONS. FORMALDEHYDE CAN CAUSE TEMPORARY EYE AND RESPIRATORY IRRITATION AND MAY AGGRAVATE RESPIRATORY CONDITIONS OR ALLERGIES. PROPER VENTILATION WILL REDUCE THE RISK OF SUCH PROBLEMS.
g.Formaldehyde Emission - ppm0.300.30
Test per ASTM E 1333
4.Product: Duraflake FR®, manufactured by Duraflake Division of Weyerhaeuser, Albany, OR.
F.Hardboard: AHA A135.4.
G.Glass for Doors: Tempered clear float, ASTM C 1048, 1/4 inch (6 mm) thick.
H.Glass for Shelves: Tempered clear float, ASTM C 1048, polished edges, 1/4 inch (6 mm) thick unless otherwise shown on Drawings.
I.Hardware:
COMMONLY USED HARDWARE AND FINISHES ARE SPECIFIED BELOW. EDIT TO MODIFY OR DELETE ITEMS NOT USED AND TO ADD OTHER ITEMS AS DESIRED. IF MORE THAN ONE TYPE OF EACH ITEM IS USED, DRAWINGS MUST DESIGNATE LOCATION AND TYPE. NOTE - BOLD FACE TYPE IS NOT USED IN THIS PARAGRAPH TO IDENTIFY OPTIONAL FEATURES TO BE SELECTED AS DESIRED. CAREFUL EDITING AND COORDINATION WITH DRAWINGS IS REQUIRED.
1.Hinges:
a.Frameless Concealed Hinges: BHMA A156.9, B01602, [100] [135] [170] degrees of opening, self-closing.
b.Semi-concealed Hinges for Overlay Doors: BHMA A156.9, B01521.
2.Pulls: Stainless steel, bent wire type, 4 inches (100 mm) long, 5/16 inch (8 mm) diameter.
3.Catches: Magnetic type, BHMA A156.9, B03141.
4.Shelf Rests and Standards:
a.Shelf rest for hole drilled in cabinet: BHMA A156.9, B0413.
b.Adjustable shelf standard and supports: BHMA A156.9, B04063 with B04083.
5.Drawer Slides:
a.Bottom edge mounted drawer slides: BHMA A156.9, B05012
b.Side mounted, full extension, zinc plated with steel ball bearings, BHMA A156.9, B05051, and rated for following loads:
1)Box Drawer: 50 lbs/pair (23 kg/pair)
2)Pencil Drawer: 45 lbs/pair (20 kg/pair)
3)File Drawer: [100 lbs/pair (45 kg/pair)] [175 lbs/pair (80 kg/pair)].
6.Door Locks: [Half mortise, BHMA A156.11, E07111] [Surface mounted, BHMA A156.11, E07121].
7.Drawer Locks: [Half mortise, BHMA A156.11, E07021] [Surface mounted, BHMA A156.11, E07041].
8.Exposed Hardware Finish:
a.Bright chrome plated: BHMA A156.18, Code 625.
b.Satin chrome plated: BHMA A156.18, Code 626.
c.Bright stainless steel: BHMA A156.18, Code 629.
d.Satin stainless steel: BHMA A156.18, Code 630.
e.Bright brass, clear coated: BHMA A156.18, Code 605.
f.Dark oxidized, satin bronze, oil rubbed: BHMA A156.18, Code 613.
J.Installation Materials:
1.Furring, Blocking, Anchor Strips: Fire-retardant treated material.
K.Substitutions: Reference Section 01630Product Substitution Procedures.
1.None permitted for fire-rated particleboard and pre-selected veneer flitches.
2.02Fabrication
WIC PROVIDES DETAILED FABRICATION REQUIREMENTS FOR CABINETS BASED UPON THE GRADE SELECTED. SPECIFIER SHOULD BE FAMILIAR WITH THESE REQUIREMENTS IN THE EVENT IT IS DESIRED TO DELETE, MODIFY OR ADD ADDITIONAL REQUIREMENTS IN THIS ARTICLE. IF PROJECT INCLUDES MORE THAN ONE GRADE, DRAWINGS MUST CLEARLY IDENTIFY SPECIFIC CABINETS AND GRADES.
A.General:
1.Ease edges of wood cabinets to 1/16 inch (1.5 mm) radius.
2.Install glass in accordance with Section 08810. Secure with removable wood stops.
B.Wood Cabinets - Transparent Finish:
1.Grade: [Economy] [Custom] [Premium] [Laboratory].
2.WIC Construction Style and Type: [A - Frameless] [B - Face frame]; Type [I - Multiple self supporting units] [II - Single length section].
a.Door and Drawer Front Style: [Flush overlay] [Reveal overlay] [Lipped] [Flush inset].
3.Matching Between Adjacent Veneer Leaves: [Book Match] [Slip Match] [Random Match].
4.Veneer Matching within Panel Face: [Running Match] [Balance Match] [Balance and Center Match].
5.Veneer Matching Within a Room: In rooms indicated on Drawings, provide veneers from a single flitch for doors, drawer fronts, and other surfaces in a sequenced set with continuous match.
DELETE SUBPARAGRAPHS 3-5 ABOVE AND INCLUDE FOLLOWING SUBPARAGRAPH IF CABINETS ARE TO BE INSTALLED IN ROOMS WITH BLUEPRINT MATCHED PANELING.
6.Comply with blueprint matching requirements of Section 06422.
7.Provide 1/4 inch (6.4 mm) plywood or hardboard dust panels drawers and compartments not directly under countertops.
C.Wood Cabinets - Opaque Finish:
1.Grade: [Economy] [Custom] [Premium] [Laboratory].
2.WIC Construction Style and Type: [A - Frameless] [B - Face frame]; Type [I - Multiple self supporting units] [II - Single length section].
a.Door and Drawer Front Style: [Flush overlay] [Reveal overlay] [Lipped] [Flush inset].
3.Provide 1/4 inch (6.4 mm) plywood or hardboard dust panels drawers and compartments not directly under countertops.
D.Plastic Laminate Clad Cabinets:
1.Grade: [Economy] [Custom] [Premium] [Laboratory].
2.WIC Construction Style and Type: [A - Frameless] [B - Face frame]; Type [I - Multiple self supporting units] [II - Single length section].
a.Door and Drawer Front Style: [Flush overlay] [Reveal overlay] [Flush inset].
3.Provide 1/4 inch (6.4 mm) plywood or hardboard dust panels drawers and compartments not directly under countertops.
2.03Shop finishing
A.General: Comply with WIC Section 5 except as modified herein.
B.Finish:
DELETE FOLLOWING SUB PARAGRAPH IF FINISH GRADE IS SAME CABINET GRADE PREVIOUSLY SPECIFIED. IF PROJECT INCLUDES MORE THAN ONE FINISH GRADE, DRAWINGS MUST CLEARLY IDENTIFY SPECIFIC CABINETS AND FINISH GRADES.
1.[Economy] [Custom] [Premium] Grade.
SELECT ONE OF THE FOLLOWING FINISH SYSTEMS AND DELETE THE OTHERS. IF PROJECT INCLUDES MORE THAN ONE FINISH, DRAWINGS MUST CLEARLY IDENTIFY SPECIFIC CABINETS AND FINISHES.
CONSULT WIC SECTION 5 FOR INFORMATION ON PROPER FINISH SYSTEMS BASED ON DURABILITY AND EASE OF REPAIR. SELECTION OF OPTIONS WITH FOLLOWING FINISH SYSTEMS ARE DEPENDENT ON GRADE, DESIRED SHEEN AND TYPE OF GRAIN. COORDINATE SELECTIONS WITH FINISH SYSTEM STANDARDS IN WIC SECTION 5.
2.System 1a - [Transparent] [Opaque]; [stain] [filler], Nitrocellulose Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
3.System 1b - [Transparent] [Opaque]; [stain] [filler], Acrylic Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
4.System 1c - [Transparent] [Opaque]; [stain] [filler], Varnish, [flat] [satin] [semi-gloss] [gloss] sheen.
5.System 1d - [Transparent] [Opaque]; [stain] [filler], Polyurethane, [flat] [satin] [semi-gloss] [gloss] sheen.
6.System 2 - [Transparent] [Opaque]; [stain] [filler], Water Reducible Acrylic Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
7.System 3a - [Transparent] [Opaque]; [stain] [filler], Catalyzed Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
8.System 3b - [Transparent] [Opaque]; [stain] [filler], Catalyzed Vinyl Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
9.System 4 - [Transparent] [Opaque]; [stain] [filler], Conversion Varnish, [flat] [satin] [semi-gloss] [gloss] sheen.
10.System 5 - [Transparent] [Opaque]; [stain] [filler], Catalyzed Polyurethane, [flat] [satin] [semi-gloss] [gloss] sheen.
11.System 6 - Transparent; [stain] [filler], Penetrating Oil, flat sheen.
12.System 7a - Opaque; Synthetic Enamel, [flat] [satin] [semi-gloss] [gloss] sheen.
13.System 7a - Opaque; Opaque Pigmented Lacquer, [flat] [satin] [semi-gloss] [gloss] sheen.
14.System 8 - [Transparent] [Opaque]; [stain] [filler], UV Curable Coating, [flat] [satin] [semi-gloss] [gloss] sheen.
SELECT ONE OF ABOVE SYSTEMS AS TOP COATING OVER FOLLOWING FIRE RETARDANT COATING IF DESIRED. VERIFY COMPATIBILITY OF SYSTEMS WITH MANUFACTURERS.
15.System 9 - [Transparent] [Opaque]; stain, Fire Retardant Coating, System.
16.System 10 - Opaque; Powder Coating.
Part 3 -Execution
3.01Examination
A.Examine surfaces adjacent to which cabinets will be installed.
B.Coordinate with responsible entity to perform corrective work on unsatisfactory surfaces.
C.Commencement of work by installer is acceptance of support conditions.
3.02Preparation
A.Condition cabinets to occupancy level environmental conditions prior to installation.
B.Verify location of required cutouts and obtain templates for cutouts.
3.03 INSTALLATION
WIC PROVIDES DETAILED INSTALLATION REQUIREMENTS FOR CABINETS BASED UPON THE GRADE(S) SELECTED ABOVE. SPECIFIER SHOULD BE FAMILIAR WITH THESE REQUIREMENTS IN THE EVENT IT IS DESIRED TO DELETE, MODIFY OR ADD ADDITIONAL REQUIREMENTS IN THIS ARTICLE. IN LOCATIONS REQUIRING SEISMIC RESTRAINT OF CABINETS, ADDITIONAL INSTALLATION REQUIREMENTS SHOULD BE PROVIDED IN THIS ARTICLE OR INSTALLATION DETAILS SHOULD BE CLEARLY SHOWN ON THE DRAWINGS. IF PROJECT INCLUDES MORE THAN ONE INSTALLATION GRADE, DRAWINGS MUST CLEARLY IDENTIFY SPECIFIC CABINETS AND INSTALLATION GRADES.
A.Install cabinets in accordance with WIC Section [14] [15].
1.Grade: [Economy] [Custom] [Premium].
B.Adjust moving parts to function smoothly.
3.04Cleaning
A.Reference Section 01740Cleaning.
3.05protection
A.Provide temporary protection to the work of this section from damage by other construction operations until [Substantial Completion] [final acceptance by Owner].
End of Section[1]
06410 - 1
[1]This specification was prepared specifically for the Duraflake Division of Weyerhaeuser, by ASC Specification Consultants. Comments or suggestions for improvement should be addressed to: ASC; 8687 Great Horned Owl Lane, Blaine, WA 98230-6306; Tel: (360) 371-5487.
Issue Date: May 15, 2002