PDH Course G253 Quiz Questions

Engineering Symbology, Prints and Drawings

  1. Bhatia, B.E.

Quiz Questions

  1. Prints are sometimes referred to as ______.
  2. Orthographic projections
  3. Xerox copies
  4. Drawings or diagrams
  5. Cad-cam
  1. Orthographic projection is a method in which different views of the subject are shown.
  1. True
  2. False
  1. The specific point of a line or a valve in P&ID can be identified using______
  1. Revision block
  2. Grid coordinates
  3. Title block
  4. Drawing scale
  1. On a 3/8” = 1’ drawing scale, if a component part measures 3” on the drawing, the actual component measures ______
  1. 2 feet
  2. 4 feet
  3. 6 feet
  4. 8 feet
  1. The term P&ID stands for ______.
  1. Plant identification drawing
  2. Piping and instrumentation drawing
  3. Plant layout and instrumentation drawing
  4. Process and instrument drawing
  1. Which of the following is an example of scaled drawing?
  1. P& IDs
  2. Electrical schematics
  3. Logic diagrams
  4. Fabrication drawing
  1. An instrument on a P&ID shows a symbol FIC. What is the order of sequence to identify this instrument?
  2. 1) Sensed parameter ; 2) The function of the instrument ; 3) the type of instrument
  3. 1) The type of instrument; 2) The function of the instrument ; 3) Sensed parameter
  4. 1) The function of the instrument ; 2) The type of instrument ; 3) Sensed parameter
  5. 1) The type of instrument ; 2) Sensed parameter ; 3) The function of the instrument
  1. A positioner is symbolized by a ______on the stem of the control valve actuator.
  1. Square box
  2. Circle
  3. Triangle
  4. Hexagon
  1. A gate valve shown with a notation “LC” stands for ______.
  1. Level controlled
  2. Locked closed
  3. Level circuit
  4. Line choked
  1. The purpose of relief valve in a hydraulic system is ______.
  1. To protect system from over pressurization
  2. To act as an unloader valve to relieve pressure when the cylinder is not in operation
  3. Both a) and b)
  4. Neither a) or b)
  1. According to course text, which among the following symbol represents double acting differential cylinder linear actuator, that has an equal force on both sides of a piston?
  1. A
  2. B
  3. C
  4. D
  1. According to the course text, which among the following symbols represent locally mounted instrument?
  1. A
  2. B
  3. C
  4. D
  1. An actuator in a fluid power system is a device that converts the hydraulic or pneumatic pressure into mechanical work.
  1. True
  2. False
  1. The list of symbols used to identify features on a drawing is referred to as a ______.
  1. Benchmark
  2. Legend
  3. Schedule
  4. Specification
  1. Fluid power valves, when electrically operated by a solenoid, are drawn in the de-energized position, unless otherwise noted on the drawing.
  1. True
  2. False
  1. The combination of a valve and an actuator is commonly called a ______.
  1. Control valve
  2. Process valve
  3. Alternative valve
  4. Piston valve

IN ANSWERING QUESTIONS 17 THROUGH 20, REFER TO FIGURE-1 AND TO THE ASSOCIATED PAGES IN YOUR COURSE MATERIAL

  1. The line Arepresents ______.
  1. An electric heat traced line
  2. An empty pipe
  3. An elastic pipe
  4. A pipe carrying ethylene
  1. The symbol B represents a ______
  1. Pipe or wire is continued on drawing XX-001, grid coordinate X-Y, flow is TO that drawing
  2. Pipe or wire is continued on drawing XX-001, grid coordinate X-Y, flow is FROM that drawing
  3. Pipe or wire is continued on drawing 001-X-Y, grid coordinate XX, flow is TO that drawing
  4. Pipe or wire is continued on drawing 001-X-Y, grid coordinate XX, flow is FROM that drawing
  1. The line C represents ______
  1. A hydraulic line
  2. A pneumatic (Air) line
  3. An inert gas line
  4. An instrument signal
  1. The line D represents ______
  1. A process flow line
  2. A steam heat tracing
  3. An inert gas line
  4. An instrument capillary
  1. ______are used to convert signal from a sensor to a form that can be sent to a remote point for processing, controlling or monitoring.
  1. Recorders
  2. Transmitters
  3. Controllers
  4. Detectors
  1. Which symbol among the following represents fixed displacement rotary motor according to the text in the course material?
  1. A
  2. B
  3. C
  4. D

IN ANSWERING QUESTIONS 23 THROUGH 26, REFER TO FIGURE-2 AND TO THE ASSOCIATED PAGES IN YOUR COURSE MATERIAL

  1. What is the name given to symbol A?
  1. Process and instrumentation device
  2. Plant integration device
  3. Proportional Integral Derivative
  4. Piping and instrumentation device
  1. What is the name given to symbol B?
  1. Closed gate valve
  2. Open gate valve
  3. Throttled gate valve
  4. Gate valve fails closed
  1. What is the name given to symbol C?
  1. Butterfly valve
  2. Stop check valve
  3. Diaphragm valve
  4. Rupture disc
  1. What is the name given to symbol D?
  1. Instrument or Process
  2. Internet Protocol
  3. Integral - Proportionate
  4. Current to Pneumatic

© A. BhatiaPage1 of 7