Ref.No.EBSL/MUM/MRKG/82/ CMD/O/93 21/07.2009
M/s.Prism Design Tooling Tech Pvt Ltd.
Soin, Mumbai – 400 022.
Kind Attn:- Mr Paresh Gosaar – Sr. Manager – Project.
Sub: -Proposal for Supply and Erection of Pre Engineered Building at ChakanPune
Dear Sir,
This is in reference to the above mentioned subject. We thank you very much for giving us the opportunity to participate in your upcoming project and we are furnishing below our most competitive offer for the same.
INTRODUCTION:
Era Building Systems Ltd.- manufacturers of world class Pre-Engineered Steel Buildings, popularly known as PEB’s, is the new born manufacturing company of Era Group, a renowned name in construction industry with a turn over exceeding Rs. 1800 Crores and growing exponentially.
The facility set up at Pantnagar, Uttaranchal is the single largest State-of-the-art manufacturing plant in Northern India with 65,000 Mt capacity, & new facility with 1,20,000Mt capacity in Nagpur in order to serve central part.EBSL is all geared to set highest standards for Pre-Engineered Steel Buildings in India.
Due to enormous action happening in the construction sector, rapid growth is witnessed across various segments of construction which led to explosion
in construction technologies. This resulted in paradigm shift towards higher usage of steel in construction.
Therefore, in the recent years metal building industry has come into limelight, a phenomenon which is well established in developed countries is catching fast in India where the industrial growth has been good over the past three years. 70% of the new industrial areas are all steel buildings.
Among the others, Automotive, Engineering, Pharmaceuticals, and most of the new age industries are of PEB’s. Besides, MNCs prefer steel buildings – a norm in the west for long.
The estimated demand for PEB’s in India is around a million MT Per annum whereas the current installed capacity is pegged at 0.30 million MT. This demand supply gap has propelled Era Group to set-up a globally recognized manufacturing unit in Uttaranchal & Maharashtra.
ABOUT THE PRODUCT:
Pre-Engineered steel buildings are the custom designed buildings that are factory-finished using high-end fabrication technologies and are shipped to job sites in CKD units. They are assembled and erected at site with hi-tensile fasteners using significantly low man-power.
The advantages of PEB’s are faster project completion, aesthetic appeal, negligible maintenance, economical and hassle free construction. EBSL offers one stop solution.
The widespread applications of PEB’s in India are –Industrial Buildings, Warehouses, Hangers, High rise building, Commercial Complexes, Indoor and Outdoor Stadiums, Metro Stations, Primary Health Centers, Schools etc.
PROJECT DETAILS:
Cost effective manufacturing, automation vis-à-vis man dependency, high end designing with cutting edge software combined with experienced professionals keep EBSL at the top of its competitors in India.
EBSL engineers manufactures top notch product quality adhering to stringent quality norms and bench marks with all new product features and better styling for international looks.
The modern manufacturing facilityhas been housed in a sprawling covered area of three and half lac square feet factory building which is one of the most imposing structures in the state of Uttaranchal .
The critical factor in any manufacturing set-up is the technology. This plant has created an opportunity for an Indian company to indigenously manufacture world-class steel buildings in India using the best machinery from Europe, North America, and Far East countries.
The installed capacity of the Rudrapur plant is 65,000 MT per annum& new facility at Nagpur with 1,20,0000 MT per annum which will be operational from November 2008.
Prominent EBSL customers:
Tata Johnson
Tata Ficossa
Titan Industries
Fedders Lloyd
Flex Packaging
Beach Mineral
Field Fresh ( Air-Tel )
Indian Arts & Crafts etc.
Bajaj Ecotech
Sikands Ltd
Lancer Foods
British Oxygen
HAL.
Videocon
L&T
Jindal Saw
Thermax
Caparo
JKS
Federal Engineers.
South Asia Breweries
Precision Stamping
Hongo India Pvt Ltd.
WEP Peripherals
Radico Khaitan
Penna Electricity
Soma Enterprise
Polar Industries
Gold Souk
RSB Transmission
Shetkari Baliraja Sugar Ltd.
Nectar Life Sciences Ltd.
Scope of Work: -
We proposed to furnish a pre-engineered steel building as described below. The building will consist of all components required to construct the primary and secondary framing (roof purlins) plus the wall and roof cladding. Hardware of the building is included. Interior partition walls, electrical, plumbing, cooling, heating, foundation, masonary walls, concrete floor or materials not specifically referenced in this proposal are not included
Building – No 1
Building Name / : / TCCSBuilding Code / : / MBMA
Bay spacing / : / 25@6
Length / : / 78.30 ( Steel Line)
Width / : / 16.00 ( Steel Line)
ClearHeight / : / 10.00Mtrs
Roof slope / : / 1:10
Total area / 1252.80+106.3636 Canopy.= 1359.16 s.m
Type Of End Frames / : / Standard Post and Beam.
Type Of Bracing On Roof / : / Cross Bracing considered.
Roof sheeting / : / 0.47mm TCT Era deck Hi-Rib Bare Galvalume sheet AZ150/550Mpa fixed with Self Tapping Screw.
Wall Sheeting / 0.50 mm TCT Era Deck Hi- Rib Color Coated Sheets AZ 150 / 550 Mpa Fixed With Self Tapping Screw
Gutter & Down Take / : / Galvalume gutter with rectangular galvalume down take of 0.50 mm thick Down take Pipes 100 mm Dia UPVC Pipe.
Paint Finish / : / All primary and secondary members shall be supplied withfactory applied one coat of Red Oxide Primer and two coat of Synthetic Enamel Paint.
Sky Lights / : / PolycorbonateSheet of 2.00 mmthick @ 5% on Roof area.& optional for Wall Light.
Terbo Vent / Considered 600 mm of 13 No`s
Ridge Vent– As Optional / 600 mmConsidered As Optional
Framed Openings
Framed Openings / 3.0Mx4.00 M - Considered
6.0Mx 7.00 M - Considered
Insulation / Considered 24 Kgs. Density of 50 mm thick Material.
Canopy. / 5 Canopies Considered with 3 mtr Projection on RollingShatters only.
Crane / 1) Considered 20/5 T Capacity with Span of 16 Mtr & Run 78.3 Mtr.
2) Considered futureExpansion with 10 M.T Crane sons both side as per drawing.
3) Crane data as per Damage
Design Loads (Live / Wind) Considered:-
The building is designed for the following Live Load and Wind Speed
Dead Load / : / 0.15 KN/m2Live Load / : / 0.57 KN/m2
Wind Speed / : / As per IS 875 Part III – 1987
Seismic Zone / : / As per IS 1893 – 2002
Applicable Codes:-
Loads are applied in accordance with:
IS -875 : Code of Practice for Design Loads for Building and Structures
IS-1893 (2002) : Criteria for Earthquake Resistance Design of
Structures.
Hot rolled and Built up sections are designed in accordance with:
IS – 800 (1984) : Code of Practice for General Construction in Steel
Steel Structure Members in GeneralBuilding Construction
Welding is applied in accordance with:
IS – 816 (1969) : Code of Practice for use of metal arc welding for
General construction in mild steel.
Material offered and technical specifications: -
S.No. / Materials / Specifications / Yield strength1. / Built-up Members / ASTM A572M Gr50 / Fy = 345 MPa
2 / Hot Rolled Secondary Members / IS : 2062 Gr. A / Fy = 250 MPa
3. / Cold Formed Secondary Members / ASTM A 570 M Gr50 / Fy =345 MPa
4. / Sheeting Panels / ASTM A 792 M / Fy = 550 MPa
5. / X-Bracing Members, Rods / IS : 2062 Gr A / Fy = 250 MPa
6. / Anchor Bolts / IS : 2062 Gr A / Fy = 250 MPa
7 / High Strength Bolts for Primary Connections. / ASTM A 325 M - ANSI 18.2.3.7 / 18.2.3.6 M
Standard Supplied Items:-
The following are included to supply:
Rigid frame structural for rafters, columns with end plates, purlins, girt made of Gr.50 steel with Y.S. 345 MPa.
Roofingsheets. (550 MPa)
Structural hardware & sheeting fasteners.
All necessary flashings, trims, eave gutters & downspout.
End lap sealant.
Anchor bolts and templates (ERA will check dimensional accuracy of anchor - bolt).
Terbo Vent – 600 mm Considered
Polycarbonate considered 5% Roof Area
. Framed Openings Considered – 3.00 M x 4.00 M & 6.0M x 7.0 M
. Insulation –Considered Insulation of24 Kgs.density of 50 mm thick
. Canopy – Considered 3 Mtr Projection on Rolling shutters only.
Exclusions:-
Interior partitions, doors and fixtures
Rolling shutters
Roof fans, pipe flashing, curbs
Wall vents, fans, doors, windows and louvers
Civil, mechanical and electrical design and materials
Concrete embedded plates of weld plate of any kind
No Glass Panels Considered in P.E.B Scope.
Over Head Tank not Considered & Also Load for Tank not Considered
Water / Electricity.
PRICE:-
Description / For Supply(In Lacs Rs) / For Erection (In Lacs Rs) / Taxes Included / Total (In Lacs Rs)1. / Pre Engineered Building at Mysore . Karnataka / 77.59 / 9.53 / Sales Tax on Supply @ 4% and Service Tax on Erection @ 10.30% / 87.12
Building / 77.59 / 9.53 / 87.12
Other terms & conditions:-
1. Commencement & completion:
The supply and Erection of building shall be completed within 120 days from the approval of G.A. drawing.
2. FORCE MAJEURE:
Our offer is subject to the standard force majeure clause as applicable in the country.
We hope you would find the above information to your entire satisfaction and for any further classifications in this regards please inform us, accordingly shall be clarified.
3. Validity of Offer:
The validity of the offer is fifteen days from the date of submission of offer.
4. Payment Terms:-
A. For Supply:
1. 20% advance with order.
2. 80 % against Performa invoice before dispatch of material.
B. For Erection:
1.40% advance against mobilization of Man Power and equipment.
2.60% on prorate basis.
We hope that you will find the above offer in line of your requirement.
For any further clarification please feel free to contact us.
Thanking You,
Your’s sincerely,
For ERA Building System Ltd.
ARJUN BHISE
Asst General Manager (Sales & Marketing)
1007, Mayuresh Chambers, Plot No-60,
Sector-11, C.B.D.Belapur, Navi Mumbai- 400604
Tel No- 67958909 /10
Mobile No- 9820083512 / 9324553068
E mail: