World’s Finest Automotive Bra Installation Instructions: C5 Corvette Rear Deck Cover 5in 1
Tools required: none.
Parts included: hook tape
Pre-Installation
1. Carefully read and follow instructions to ensure optimal performance
2. Thoroughly wash & wax vehicle surfaces first to prevent entrapment of moisture and/or debris between paint finish and the SpeedLingerieTM.
Rear Deck Cover Installation-to provide paint protection while loading cargo in/out of the trunk
1. Open the rear deck lid.
2. Orient the SpeedLingerieTM with the two loops ‘up’, and the felt side ‘in’.
3. Attach the two loops onto the top two factory installed pins for the cargo net.
4. Let the SpeedLingerieTM drape over the top of the rear deck, and down the rear end of the vehicle.
5. You can now load items in/out of the trunk-and protect your paint finish.
6. To store the SpeedLingerieTM, roll it up from the bottom (felt side out), leave the two loops hooked over the factory cargo net pins, and lay it inside the truck area just in front of the cargo net.
7. Close the rear deck lid.
Trunk Mat Installation–to protect the trunk carpeting from dirt
1. Open the rear deck lid.
2. Lay the SpeedLingerie flat on the floor of the trunk area.
3. You can now load item into the trunk – and protect your carpeting.
Convertible Top Curtain Installation(for Convertibles Only)-to protect the convertible top
1. Open the rear deck lid
2. Remove the hook-tape strip from the top edge of the SpeedLingerieTM . Affix this strip of hook tape to the 1” x 1” square channel that runs along the topedge of the trunk compartment.
3. Attach the top edge of the SpeedLingerie with loop tape to the hook tape. Tuck the bottom edge of the SpeedLingerieTM under the convertible top(with the convertible top in the down position).
4. You can now load item into the trunk – and protect your Convertible top.
Door Cover Installation-to provide paint protection from door dings in the garage or a parking lot
1. Open the driver door.
2. Raise the door window all the way up.
3. Orient the SpeedLingerieTM with the notched side ‘up’ (to conform to the outside door mirror).
4. With the door window up, slip the tension cord over the glass.
5. Pull down on the SpeedLingerieTM, and slip the notched edge of the SpeedLingerieTM under the outside door mirror.
6. Adjust the SpeedLingerieTM so it hangs evenly.
7. Shut the door (the tension cord will be locked inside the door to prevent theft of the SpeedLingerieTM).
8. You can now park two cars in your garage, or park in a parking lot – and protect your door from dings
Front Fender Cover Installation-to provide paint protection while working in the engine compartment
1. Open the hood.
2. Orient the SpeedLingerieTM with the two loops ‘up’, and the felt side ‘in’.
3. Attach the rear loop over the factory installed rear hood stand-off, near the base of the windshield.
4. Attach the front loop over the factory installed front hood stand-off, just inside the headlight assy.
5. Adjust the SpeedLingerieTM so it hangs evenly.
6. You can now reach into the engine compartment – and protect your fender form scratches.
Care & Maintenance
1. For best results, be sure that vehicle surfaces are clean and dry before installing SpeedLingerie.
2. You may apply a quality vinyl conditioner to the SpeedLingerieTM if you so desire.
3. Always inspect SpeedLingerieTM fasteners and surfaces that contact vehicle for possible debris, sand, grit, etc… and remove before installation.
4. Periodically remove SpeedLingerieTM to allow complete aeration of vehicle paint finish and SpeedLingerieTM materials.
5. Remove SpeedLingerieTM before washing vehicle.
6. Remove SpeedLingerieTM after exposure to rain or other fluids/moisture.
7. Clean outer vinyl surfaces of SpeedLingerieTM with a high quality conditioner during routine car maintenance.
8. Clean felt inner surface with water if necessary, allowing it to dry completely, and brush/vacuum out any remaining particles.
9. Rubber will stain vinyl. DO NOT store your SpeedLingerieTM in direct contact with any rubber products (i.e.: tires, hoses, etc) as vinyl is a very porous material and will absorb the black carbon in rubber products, resulting in a stain on the vinyl.
Congratulations again on your SpeedLingerie purchase.
Installation Questions? Call 1(800) 570-1579 for assistance.
Page 1
Rev0705