Acucraft Fireplace Systems October 2017
19672 172nd Street
Big Lake, Minnesota 55309
Toll Free 888-317-6499
Phone 763-263-3156
Fax 763-263-8311
Website www.acucraft.com
Guide Specification
Specifier Notes: This guide specification is written in Construction Specifications Institute (CSI) 3-Part Format in accordance with The CSI Construction Specifications Practice Guide, MasterFormat, SectionFormat, and PageFormat.
This Section must be carefully reviewed and edited by the Architect to meet the requirements of the Project and local building code. Coordinate this Section with Conditions of the Contract, Division 01, other specification sections, and the Drawings. Delete all Specifier Notes after editing this Section.
Section numbers and titles are based on MasterFormat 2016 Edition.
SECTION 10 31 00.13
CUSTOM MANUFACTURED FIREPLACES
Specifier Notes: This Section covers Acucraft Fireplace Systems custom, vented, decorative, gas appliance fireplaces using natural gas or propane. Consult Acucraft Fireplace Systems for assistance in editing this Section as required for the Project.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. Custom gas fireplaces.
1.2 RELATED REQUIREMENTS
Specifier Notes: Edit the following list of related sections as required for the Project. Limit the list to sections with specific information that the reader might expect to find in this Section, but is specified elsewhere.
A. Section 22 10 00 – Plumbing Piping.
B. Section 26 05 00 – Common Work Results for Electrical.
1.3 REFERENCE STANDARDS
Specifier Notes: List reference standards used elsewhere in this Section, complete with designations and titles. Delete reference standards from the following list not used in the edited Section.
A. ANSI Z21.50/CSA 2.22 – Vented Decorative Gas Appliances.
B. CAN/CSA B149.1 – Natural Gas and Propane Installation Code.
C. CSA C22.1 – Canadian Electrical Code, Part I, Safety Standard for Electrical Installations.
D. NFPA 54 (ANSI Z223.1) – National Fuel Gas Code.
E. NFPA 70 – National Electrical Code (NEC).
F. NFPA 211 – Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances.
G. UL 103 – Standard for Factory-Built Chimneys for Residential Type and Building Heating Appliances.
1.4 PREINSTALLATION MEETINGS
Specifier Notes: Edit the Preinstallation Meetings article as required for the Project. Delete this article if not required.
A. Convene preinstallation meeting [1 week] [2 weeks] before start of installation of custom gas fireplaces.
B. Require attendance of parties directly affecting Work of this Section, including Contractor, Architect, installer, and manufacturer’s representative.
C. Review the Following:
1. Materials.
2. Operation.
3. Media.
4. Accessories.
5. Source quality control.
6. Installation.
7. Field quality control.
8. Adjusting.
9. Cleaning.
10. Closeout activities.
11. Protection.
12. Coordination with other Work.
1.5 SUBMITTALS
Specifier Notes: Edit the Submittals article as required for the Project. Delete submittals not required.
A. Submittals: Comply with Division 01.
B. Product Data: Submit manufacturer’s product data, including installation instructions.
C. Shop Drawings: Submit manufacturer’s shop drawings, indicating dimensions, installation clearances, materials, components, equipment, ventilation system, gas lines, electrical wiring diagrams, hardware, finish, options, and accessories.
D. Manufacturer’s Certification: Submit manufacturer’s certification that materials comply with specified requirements and are suitable for intended application.
E. Manufacturer’s Project References: Submit manufacturer’s list of 10 successfully completed custom gas fireplace projects of similar size and scope to this Project, including project name and location, name of architect, and type and quantity of custom gas fireplaces furnished.
F. Installer’s Project References: Submit installer’s list of 10 successfully completed custom gas fireplace projects of similar size and scope to this Project, including project name and location, name of architect, and type and quantity of custom gas fireplaces installed.
G. Operation and Maintenance Data:
1. Submit manufacturer’s operation and maintenance manual, including the following:
a. Operation, maintenance, adjustment, and cleaning instructions.
b. Safety information.
c. Troubleshooting guide.
d. Parts list.
e. Electrical wiring diagrams.
2. Provide detailed information required for Owner to properly operate and maintain custom gas fireplaces.
H. Warranty Documentation: Submit manufacturer’s standard warranty.
1.6 QUALITY ASSURANCE
A. Manufacturer’s Qualifications: Manufacturer regularly engaged in the manufacturing of custom gas fireplaces of similar type to that specified for a minimum of 10 years.
B. Installer's Qualifications:
1. Installer regularly engaged in installation of custom gas fireplaces of similar type to that specified for a minimum of 5 years.
2. Use persons trained for installation of custom gas fireplaces.
1.7 DELIVERY, STORAGE, AND HANDLING
A. Delivery Requirements: Deliver materials to site in manufacturer’s original, unopened containers and packaging, with labels clearly identifying product name and manufacturer.
B. Storage and Handling Requirements:
1. Store and handle materials in accordance with manufacturer’s instructions.
2. Keep materials in manufacturer’s original, unopened containers and packaging until installation.
3. Store materials in clean, dry area indoors.
4. Do not store materials directly on floor.
5. Store materials out of direct sunlight.
6. Keep materials from freezing.
7. Protect materials and finish during storage, handling, and installation to prevent damage.
1.8 WARRANTY
A. Warranty Period:
1. Firebox: Lifetime.
2. Main Burner: 5 years.
3. Control Board: 2 years.
4. Pilot Burner, Gas Control Valve, Media, Other Gas Components: 1 year.
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Manufacturer: Acucraft Fireplace Systems, 19672 172nd Street, Big Lake, Minnesota 55309. Toll Free 888-317-6499. Phone 763-263-3156. Fax 763-263-8311. www.acucraft.com. .
Specifier Notes: Specify if substitutions will be permitted.
B. Substitutions: [Not permitted] [Comply with Division 01].
C. Single Source: Provide custom gas fireplace materials from single manufacturer.
2.2 CUSTOM GAS FIREPLACES
A. Description: Vented, decorative, gas appliance fireplace.
Specifier Notes: Specify gas type.
B. Gas Type: [Natural gas] [Propane].
C. Conformance:
1. ANSI Z21.50/CSA 2.22.
2. NFPA 54 (ANSI Z223.1).
3. NFPA 211.
D. Fireplace Style:
Specifier Notes: Specify fireplace style.
1. Single sided.
2. See-through.
3. Indoor/outdoor.
4. Circular.
5. Indoor fire pit.
6. Four sided.
7. Peninsula.
8. Panoramic.
9. Front with right view.
10. Front with left view.
11. Vertical.
12. “BLAZE6 SS”.
13. “BLAZE6” indoor/outdoor.
14. “BLAZE10”.
E. Dimensions:
Specifier Notes: Specify dimensions for the custom gas fireplaces. Specify diameter for circular fireplaces.
1. Overall Dimensions:
a. Height: ______inches.
b. Width: ______inches.
c. Depth: ______inches.
d. Diameter: ______inches.
2. Frame Dimensions:
a. Height: ______inches.
b. Width: ______inches.
c. Depth: ______inches.
d. Diameter: ______inches.
3. Viewing Area:
a. Height: ______inches.
b. Width: ______inches.
c. Depth: ______inches.
d. Diameter: ______inches.
4. Burner Width: ______inches.
Specifier Notes: Specify no glass, partial glass, or full glass.
F. Glass: [Open, no glass] [Partial] [Full].
Specifier Notes: Specify glass type. Single pane is standard.
1. Single pane.
2. “Airshield” system.
3. “Glass Cooling” System: Dual panes.
4. Firescreen.
G. Frame:
Specifier Notes: Specify the frame type.
1. Type: [Standard, 1-1/2-inch reveal] [Hidden, 1/2-inch reveal].
Specifier Notes: Specify the frame finish. Matte black steel is standard.
2. Finish: [Steel, matte black] [Stainless steel, polished] [Stainless steel, brushed] [Cor-ten steel].
H. Interior:
Specifier Notes: Specify interior options. Consult Acucraft Fireplace Systems for additional information.
1. Mesh backer.
2. Reflective porcelain.
2.3 OPERATION
A. Venting:
1. Direction:
Specifier Notes: Specify venting direction. Consult Acucraft Fireplace Systems for additional information.
a. Vertical: Top exit.
b. Horizontal 90: Up and out.
c. Horizontal Straight: Side exit.
d. Down Draft: Exits downward under floor or grade.
B. Flue: UL 103, HT.
C. Electrical: 120 V, 20 A.
D. Draft Control Board: ADC 100.
E. Inline Fan: Fantech.
F. Chimney Fan: RS, RSIF, TDF.
2.4 MEDIA
Specifier Notes: Specify type of media. Delete media types not required.
A. Glass Media: “1/4-Inch Classic Collection” crushed glass.
Specifier Notes: Specify the glass media color.
1. Color: [Azuria] [Black] [Bronze] [Champagne] [Clear] [Cobalt] [Copper] [Evergreen] [Gray] [Pacific Blue] [Solex] [Starfire].
B. Glass Media: “1/4-Inch Premium Collection” crushed glass.
Specifier Notes: Specify the glass media color.
1. Color: [Azuria Reflective] [Black Reflective] [Bronze Reflective] [Champagne Reflective] [Cobalt Reflective] [Copper Reflective] [Evergreen Reflective] [Gold Reflective] [Gray Reflective] [Pacific Blue Reflective] [Platinum Reflective].
C. Glass Media: “1/2-Inch Classic Collection” crushed glass.
Specifier Notes: Specify the glass media color.
1. Color: [Azuria] [Black] [Bronze] [Clear] [Cobalt] [Copper] [Evergreen] [Gray] [Pacific Blue] [Starfire].
D. Glass Media: “1/2-Inch Premium Collection” crushed glass.
Specifier Notes: Specify the glass media color.
1. Color: [Azuria Reflective] [Black Reflective] [Bronze Reflective] [Cobalt Reflective] [Copper Reflective] [Evergreen Reflective] [Gray Reflective] [Pacific Blue Reflective] [StarFire Reflective].
E. Stone Media for Open Fireplaces: “Fire Stones” semi-polished stones.
Specifier Notes: Specify the stone media color.
1. Color: [Ivory-Tan] [Off-White/Light Gray] [Slate-Black (Gray)].
F. Stone Media for Open Fireplaces: “Fire Stones” glossy stones.
Specifier Notes: Specify the stone media color.
1. Color: [Off-White/Light Gray] [Slate-Black].
G. Stone Media for Open Fireplaces: River rock.
Specifier Notes: Specify the stone media color.
1. Color: [Assorted] [Designer] [Ivory] [Slate] [Terracotta].
H. Stone Media for Open Fireplaces: Lava rock.
Specifier Notes: Specify the stone media color.
1. Color: [Black] [Red].
I. Stone Media for Enclosed Fireplaces: “Fire Stones” semi-polished stones.
Specifier Notes: Specify the stone media color.
1. Color: [Ivory-Tan] [Off-White/Light Gray] [Slate-Black (Gray)].
J. Stone Media for Enclosed Fireplaces: “Fire Stones” glossy stones.
Specifier Notes: Specify the stone media color.
1. Color: [Off-White/Light Gray] [Slate-Black].
K. Stone Media for Enclosed Fireplaces: Lava rock.
Specifier Notes: Specify the stone media color.
1. Color: [Black] [Red].
L. Log Sets: “Grand Canyon”.
2.5 ACCESSORIES
Specifier Notes: Specify required accessories.
A.
2.6 SOURCE QUALITY CONTROL
Specifier Notes: Specify third-party certification tests or manufacturer’s tests. Consult Acucraft Fireplace Systems for additional information.
A. Third-Party Certification Tests:
1. ANSI Z21.50/CSA 2.22.
2. Factory tested by accredited, independent, ANSI-approved, third-party, testing certification laboratory.
3. Provide label and ANSI listing for each approved custom gas fireplace.
B. Manufacturer’s Tests:
1. ANSI Z21.50/CSA 2.22.
2. Factory tested by manufacturer.
3. Provide manufacturer’s approval certificate for each approved custom gas fireplace.
PART 3 EXECUTION
3.1 EXAMINATION
A. Examine areas to receive custom gas fireplaces.
B. Verify surfaces to support custom gas fireplaces are clean, dry, flat, plumb, level, square, stable, rigid, and capable of supporting the weight.
C. Notify Architect of conditions that would adversely affect installation or subsequent use.
D. Do not begin installation until unacceptable conditions are corrected.
3.2 INSTALLATION
A. Install custom gas fireplaces in accordance with manufacturer’s instructions at locations indicated on the Drawings.
Specifier Notes: Include the following paragraph for projects in United States.
B. Install custom gas fireplaces in accordance with:
1. NFPA 54 (ANSI Z223.1).
2. NFPA 70.
3. NFPA 211.
Specifier Notes: Include the following paragraph for projects in Canada.
C. Install custom gas fireplaces in accordance with:
1. CAN/CSA B149.1.
2. CSA C22.1.
D. Install custom gas fireplaces level and plumb.
E. Install custom gas fireplaces with clearances to combustibles in accordance with manufacturer’s instructions.
F. Securely anchor custom gas fireplaces in place to supports in accordance with manufacturer’s instructions.
Specifier Notes: Delete the Field Quality Control article if third-party inspection and acceptance tests are not required for the Project. Consult Acucraft Fireplace Systems for additional information.
3.3 FIELD QUALITY CONTROL
A. Third-Party Inspection and Acceptance Tests:
1. ANSI Z21.50/CSA 2.22.
2. Inspect, test, and approve installed custom gas fireplaces by accredited, independent, ANSI-approved, third-party, testing certification laboratory and manufacturer’s factory-trained and certified representative.
3. Do not fully finish custom gas fireplaces with facing materials until after third-party inspection and acceptance tests are completed.
3.4 ADJUSTING
A. Adjust custom gas fireplaces for proper operation in accordance with manufacturer’s instructions.
B. Damaged Components: Remove and replace with new material, damaged components that cannot be successfully repaired, as determined by Architect.
C. Glass Panels: Remove and replace with new material, glass panels that are broken, cracked, damaged, or visually flawed.
D. Finish: Repair minor damages to finish in accordance with manufacturer’s instructions and as approved by Architect.
3.5 CLEANING
A. Clean custom gas fireplaces promptly after installation in accordance with manufacturer’s instructions.
B. Do not use harsh cleaning materials or methods that could damage finish.
3.6 CLOSEOUT ACTIVITIES
Specifier Notes: Edit the Closeout Activities article as required for the Project.
A. Demonstration, Instruction, and Training:
1. Demonstrate to [Architect] [and] [Owner] that custom gas fireplaces function properly.
2. Provide instruction and training of Owner’s personnel in operation and maintenance of custom gas fireplaces.
3. Provide demonstration, instruction, and training by installer.
3.7 PROTECTION
A. Protect installed custom gas fireplaces from damage during construction.
END OF SECTION
Acucraft Fireplace Systems
Custom Gas Fireplaces 10 31 00.13 - 2