90% Specifications

Project Name: PFIZER

Location: Morris Plains, NJ

Date: 11-18-2004

Item No 1 - WALK-IN COOLER/ FREEZER

Manufacturer: Kolpak Industries, Inc.

Model No.: Custom

Quantity Req'd.: 1

Status: In Contract

Unit to be a Refrigerator +35° F. and/or Freezer -10° F. of size and shape as shown on plan x 9' - 2 1/4" high.

Wall and ceiling panels shall be 4" urethane, U.L.Flame Spread 25 insulation. Panels are without wooden structural members.

Hinged entrance door(s) to be flush type, hinged as shown on plan.

Provide one (1) lot removable closure panels with channels, the same finish as exterior panels to ceiling. (F.S.E. Contractor to verify ceiling height).

One (1) lot of trim strip, where required to close in wall gaps, of same finish as exterior panels to finished ceiling. (F.S.E. Contractor to verify height).

Options:

  • Floorless with flat bottom wall panels in recess. Slab urethane insulation, vapor barrier and quarry tile w/ minimum 2" setting bed by General Contractor.
  • Embossed aluminum white interior and exposed exterior.
  • Unexposed exterior finish to be galvalume.
  • Hinged doors to be 36" wide x 78" high with third hinge.
  • Dead bolt lock per Specific Conditions (on exterior doors only).
  • Anti -condensate heaters in full perimeter of door and frame (freezer only).
  • Aluminum diamond tread kick plate, 3'-0" high on exterior and interior of door and jamb.
  • 14" x 14" vision panel and automatic door closer, Kason K-1094.
  • Thru ceiling door electrical assembly as shown on detail E-1-4.
  • Factory cut door for tile floor conditions.
  • Approved fluorescent light fixtures and switches, installed and wired by the Electrical Division per detail E-1-4. (See electrical plan for quantity and location of lights and switches).
  • Modularm 75B, recessed with thru ceiling door electrical as shown on detail E-1-4.
  • 16 ga. stainless steel hat shaped rub rail on exposed exterior.
  • Stainless steel corner guards at exposed corners.
  • Wainscot on exposed exterior, 1/8" aluminum diamond plate. Top to align with top of kickplate on door.

Item No 2 - CONDENSING UNIT, AIR COOLED REMOTE

Manufacturer: Kolpak Industries, Inc.

Model No.: PR100M

Quantity Req'd.: 1

Status: In Contract

F.S.E.C. to provide the necessary refrigeration lines required to operate and maintain the refrigeration system for Item 1, refrigerated compartment. Unit to be part of the remote refrigeration system for Item 3, Evaporator Coil.

F.S.E.C. to coordinate with the electrical/plumbing contractor to provide a complete and operable refrigeration system.

Provide start-up, five (5) year compressor warranty and one (1) year refrigeration service contract.

Division 16 to wire to safety disconnect switch.

  • Provide outdoor ambient package.
  • Unit to be located on roof by Architect. See architectural plan.
  • Assume a 75' refrigeration line run.

Item No 3 - EVAPORATOR COIL, MEDIUM TEMPERATURE

Manufacturer: Kolpak Industries, Inc.

Model No.: AM-104

Quantity Req'd.: 1

Status: In Contract

Unit to be adequately sized to operate Item 1, Refrigerator Compartment @ +35° F. Electrical hook-up and interconnecting of system to be by the Electrical Contractor.

Item No. 4 - SPARE NUMBER

Item No 5 - RACK, UTILITY - UNIVERSAL ANGLE

Manufacturer: Crescent Metal Products, Inc.

Model No.: 207-UA-13

Quantity Req'd.: 2

Status: In Contract

Rack, Mobile Utility, full height, open sides, universal slides for 12"x20" thru 18"x26" pans, slides on approximately 1-1/2" centers, welded tubular aluminum frame.

Item No 6 - SHELVING UNIT

Manufacturer: Metro

Model No.: METROMAX

Quantity Req'd.: LOT

Status: In Contract

Size and shape as shown on plan x 4 tiers high. 74" high posts to match shelf type. MetroMax Construction

  • Unit to be mobile mounted 5" diameter polyurethane swivel casters, two (2) swivel and two(2) with brakes.

Item No 7 - DUNNAGE PLATFORM, MOBILE

Manufacturer: Metro

Model No.: SUPER ERECTA

Quantity Req'd.: LOT

Status: In Contract

Dunnage unit of size and shape as shown on plan, mobile, wire shelves, epoxy on zinc-plating, mounted on 4-1/2" dia. casters.

Item No 8 - TILT TRUCK FOR CARDBOARD

Manufacturer: Rubbermaid Commercial Products

Model No.: 1314

Quantity Req'd.: 1

Status: In Contract

Tilt Truck, Utility Duty.

Item No 9 - CONDENSING UNIT, AIR COOLED REMOTE

Manufacturer: Kolpak Industries, Inc.

Model No.: PR154L

Quantity Req'd.: 1

Status: In Contract

F.S.E.C. to provide the necessary refrigeration lines required to operate and maintain the refrigeration system for Item 1, Freezer compartment. Unit to be part of the remote refrigeration system for Item 10, Evaporator Coil.

F.S.E.C. to coordinate with the electrical/plumbing contractor to provide a complete and operable refrigeration system.

Provide start-up, five (5) year compressor warranty and one (1) year refrigeration service contract.

Division 16 to wire to safety disconnect switch.

  • Provide outdoor ambient package.
  • Unit to be located by Architect . See architectural plan.
  • Assume 75' refrigeration line run.
  • Loose timeclock (freezer only) installed above walk-in freezer.

Item No 10 - EVAPORATOR COIL, LOW TEMPERATURE

Manufacturer: Kolpak Industries, Inc.

Model No.: AM-090

Quantity Req'd.: 1

Status: In Contract

Unit to be adequately sized to operate Item 1, Freezer Compartment @ -10° F. Electrical hook-up and interconnecting of system to be by the Electrical Contractor.

Item No 11 - RACK SHELF, SOILED, WALL-MOUNTED

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Unit to be of size and shape as shown on plan and per detail C-8-4. Wall mount unit above Item 12, Soiled Dishtable Assembly.

Item No 12 - SOILED TRAY HANDLING SYSTEM

Manufacturer: AEROWERKS

Model No.: SBC/GRC/ST

Quantity Req'd.: 1

Status: In Contract

Pass Thru Window Frame and Sight & Sound Baffle – 1 required

Provide stainless steel full perimeter window frame integral with Tray Return Conveyor. Food Service Equipment Contractor to verify window opening with architectural drawings. Provide stainless steel sight and sound baffle with access doors and lights integral with the Tray Return Conveyor.

Slat Belt Soiled Tray Return Conveyor – 1 required

Provide conveyor as shown on plan. Unit shall be Aerowerks model SBC Conveyor.

SBC Belting

SBC Belting shall be Aerowerks K10SF-AD. Belting shall have a tensile strength of 6100lbs and shall “side-flex” to a minimum of 18” centerline radius at corners on consultant’s drawings. There shall be no sliding friction at corners between belt and groove or guide rail. Both slide bed groove and return track shall be self-cleaning by the action of the belt. Belt take-up shall be accomplished by compression of slack in the return strand using belt guides integrally mounted in the drive unit.

Drive Frame

All Stainless steel angle frame with 1-5/8” diameter 6” high stainless steel legs and adjustable stainless steel bullet feet

Drive Housing

Drive frame shall be fitted with a 18 ga. stainless steel housing to enclose drive frame on all sides. For access provide stainless steel double wall hinged insulated doors. Where side or end panels are fitted to frame, they shall be sealed with silicone. Drive cabinet to house all necessary plumbing and detergent injection pump for the belt wash system.

Drive Tank

Provide all welded 14 ga stainless steel wash chamber equipped with lift- off access panels and removable scrap tray.

Drive Shaft

Provide 1” stainless steel drive shaft mounted within wash chamber on dual-type sealed bearings (Aerowerks grease-filled sealed cartridge inside chamber; precision ball bearing flange cartridge outside chamber).

Belt Wash

Provide wash system consisting of stainless steel manifolds inside wash chamber. Spray manifolds to be strategically located to effectively clean the belt, and shall be easily removable without tools.

Drive Motor

Provide variable speed ¾ hp DC Motor and gear reducer. Speed to be changed by turning a knob located on the control panel.

Plumbing Connections

At Drive Cabinet:

1 ½” waste

½” hot and cold water

At Tail Tank

1 ½” waste

Slide Bed

Provide 14 ga. 304 stainless steel bed formed with vertical and horizontal corners coved to a ¾” radius. Unit shall be reinforced with channel mounted on stainless steel legs with adjustable bullet feet and rails.

Control System

Provide Main Control Center containing start-stop, belt wash, speed control and disconnect circuit breaker. All components shall be neatly contained in a stainless steel watertight enclosure. All wiring shall conform to the latest UL standards. The electrical contractor shall bring 208V/1phase/15A to the main of the panel, but wiring from the equipment to this panel shall be done by Aerowerks, and all wiring shall be carried in liquid-tight conduits, including conveyor motor and controls. All electrical controls shall be approved for wet conditions and shall comply with all applicable codes. All enclosures for electrical components must be watertight.

Soiled Dishtable – 1 required

Provide Soiled Dishtable, 14 ga. stainless steel top and trough as shown on plan. Table shall be formed with vertical and horizontal corners coved to a ¾” radius. Provide magnetic silver saver, hose clean up station, disposer control panel bracket as shown on the plan.

PVC roller tray transfer conveyor shall form integral part of Soiled Dish Table. Rollers shall be blue PVC, fitted with polypropylene bearings with stainless steel balls. Rollers shall be spaced at approximately 4” centers and shafts shall be 7/16” hexagon aluminum securely bolted to side rails. Guide rails shall be 1/8” x 2” stainless steel supported on conveyor bed. Furnish table with pre-wired accumulation switch.

Overhead Rack Shelf shall be 1” diameter stainless steel tubular construction and properly underbraced and supported on Soiled Dishtable.

Provide pre-rinse sink of size and shape as shown on plan. Unit shall be 14 ga. stainless steel construction and shall form integral part of item Soiled Dishtable. Pre-rinse unit shall be T & S B-126 mounted on backsplash of pre-rinse sink. Unit shall be complete with mixing valve, vacuum breaker and T & S B-107 spray head.

Support table on 1 5/8” diameter stainless steel legs with adjustable bullet feet. Legs shall be positioned to align up front-to-back for maximum access for cleaning. Legs shall be supported with 14 gauge stainless steel leg channels. All crossrails shall be fully welded to legs with all welds polished and ground smooth.

Installation & Warranty – 1 required

Aerowerks shall be responsible for all interconnections of plumbing and electrical work required for conveyor system. Final connections to building services by others. Aerowerks shall install and adjust system to owner’s satisfaction and shall provide adequate instructions to operating personnel. System shall be guaranteed for a period of one year for parts and labor under normal operating conditions, from date system is turned over to owner.

Refer to preliminary shop drawings P0400431, sheets 1 and 2.

Item No 13 - FOOD WASTE DISPOSER

Manufacturer: The Salvajor Company

Model No.: 300

Quantity Req'd.: 1

Status: In Contract

Electrical characteristics as indicated on electrical plan.

  • ARSS-TR Control Panel (with auto-reversing and built in safety disconnect switch/ specify in dishwash areas)
  • 6-1/2" sink collar with stopper (weld-in)
  • Fixed nozzle
  • Rubber scrap ring
  • Domed silver saver
  • Stainless steel dejamming prong
  • Time delay for ARSS-2

Item No 14 - DISHWASHER, CONVEYOR TYPE

Manufacturer: Hobart Corporation

Model No.: C44A-RL

Quantity Req'd.: 1

Status: In Contract

Hobart Corp. Model No. C44A-RL Dishwasher, Steam Coil, Conveyor Type, convertible, high temp, single tank design (wash), approx. 200 racks/hour capacity, all stainless steel finish.

  • Vent hood w/ stack and locking damper at load and unload end.
  • Single point electrical connection.
  • Conveyor dwell.
  • Table limit switch.

Item No 15 - DISHWASHER VENT DUCT, LOAD END

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Construct per detail C-8-13. (inverted louvers). FSE Contractor to verify ceiling height.

Item No 16 - STEAM BOOSTER HEATER

Manufacturer: Hobart Corporation

Model No.: 180-1

Quantity Req'd.: 1

Status: In Contract

Steam Booster Heater.

  • Stainless steel enclosure by Hobart.

Item No 17 - DISHWASHER VENT DUCT, UNLOAD

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Construct per detail C-8-13. (inverted louvers). FSE Contractor to verify ceiling height.

Item No 18 - DISHTABLE, CLEAN

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Unit to be of size and shape as shown on plan x 34" high to drainboard level with 10" high splash per details C-1-1A Type "D" edge, C-1-1B backsplash and C-8-1. Provide with the following:

  • Provide front to back and rear crossrails.
  • Open base type table, no undershelf.
  • Front to back crossbracing only.
  • Accommodate table limit switch as shown on electrical plan.
  • Accommodate Item 16, Booster Heater, floor mounted.

Item No. 19 - SPARE NUMBER

Item No 20 - DISH DOLLY

Manufacturer: Metro

Model No.: PCD9

Quantity Req'd.: 1

Status: In Contract

Dish Dolly.

  • FSEC to confirm plate size with Owner prior to ordering.

Item No 21 - WATER TREATMENT SYSTEM

Manufacturer: Everpure, Incorporated

Model No.: 9320-43

Quantity Req'd.: 1

Status: In Contract

Everpure, Inc Model No EV9330-43, Water Filter Assembly, wall-mounting bracket and gauge assembly. See plumbing plan KA-2 for equipment units connected to filter.

  • Provide with 1 ea. Amtrol model WX-405 Tank, 24 gallon drawdown.

Mount system as specified, tee at effluent ¾” valve, one side of tee to Amtrol tank, the other to supply kitchen equipment.

Item No 22 - SINK, THREE COMPARTMENT

Manufacturer: CUSTOM Fabrication

Model No.: NNNSTCFM-RL

Quantity Req'd.: 1

Status: In Contract

Unit to be of size and shape as shown on plan x 34" high to drainboard level with 10" high splash per details C-1-1A Type "D" edge, C-1-1B backsplash, C-8-1 30 x", rinse 24", sanitize 24", all 14" deep with the following requirements:

  • Overflow collector per detail C-8-8.
  • Undershelf below right/ left drainboard section per detail C-8-1.
  • Front to back and rear crossrails.
  • Two type 2 faucet(s).

Item No 23 - SHELF, WALL-MOUNTED, TWO-TIER

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Unit to be of size and shape as shown on plan per detail C-1-2 with the following requirements:

  • Louvers per detail C-1-2.
  • Two-tier unit, first tier (lower shelf) to be 12" wide, second tier (upper) to be 15" wide.

Item No 24 - POT AND PAN RACK

Manufacturer: Metro Equipment Corporation

Model No.: PR48ES

Quantity Req'd.: 1

Status: In Contract

Metro Model No. PR48ES, Pot & Pan Rack.

Item No 25 - HAND SINK

Manufacturer: IMC/Teddy Food Service Corp.

Model No.: CSW

Quantity Req'd.: 1

Status: In Contract

IMC/TEDDY Model No. CSW Hand Sink.

  • Standard faucet.

Item No. 26 - SPARE NUMBER

Item No. 27 - SPARE NUMBER

Item No 28 - TILT TRUCK FOR TRASH

Manufacturer: Rubbermaid Commercial Products

Model No.: 1314

Quantity Req'd.: 1

Status: In Contract

Tilt Truck, Utility Duty.

Item No. 29 - SPARE NUMBER

Item No 30 - HIGH DENSITY SHELVING

Manufacturer: Metro

Model No.: High Density Shelving - MetroMax

Quantity Req'd.: One lot

Status: In Contract

One track shelving kit including:

  • 1 ea. QTTE21 MetroMax Q Top Track Stationary End Unit kit.
  • 2 ea. QTTM21C MetroMax Q Top Track Mobile Unit Kit.
  • 16 ea. Q21160G2 MetroMax Q shelf.
  • 1 ea. TTS7NA Track set, 7’ long.

Item No 31 - WORK TABLE

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Unit to be size and shape as shown on plan x 36" high w/ 6" high splash per detail C-1-1A Type "A" edge, C-1-1B backsplash and C-7-1. Left end splash as shown on plan. Provide with the following:

  • Undershelf per C-7-1.
  • One (1) 20" x 20" x 5" deep drawer per detail C-1-3A, C-1-3B, C-1-3C and C-1-3D, lock hasp.
  • Angle slides at bottom of drawer w/ one (1) Richlite 1/2" thick cutting board per detail C-1-3C.

Item No. 32 - SPARE NUMBER

Item No 33 - UTILITY CART

Manufacturer: Metro

Model No.: BC1627-34

Quantity Req'd.: 5

Status: In Contract

Metro Model No. BC1627-34 Cart, Utility.

  • Color selected by Architect.

Item No 34 - SHELF, WALL-MOUNTED, TWO-TIER

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

Unit to be of size and shape as shown on plan per detail C-1-2 with the following requirements:

  • Two-tier unit, first tier (lower shelf) to be 12" wide, second tier (upper) to be 15" wide.

Item No 35 - COFFEE BREWER

Manufacturer: Fetco, Inc

Model No.: CBS-51H15-3

Quantity Req'd.: 1

Status: In Contract

  • Color Selected by Architect
  • Half batch brew capacity
  • Five (5) 2.5 liter gravity flow thermos with sight gauges
  • Flexible disconnect per specific conditions
  • Connect to Item 21, Water Treatment Unit.

Item No 36 - REFRIGERATOR, TWO SECTION

Manufacturer: Traulsen & Company, Inc.

Model No.: RHT 1-32 WUT

Quantity Req'd.: 1

Status: In Contract

  • Doors w/locks, common keyed
  • Casters.
  • Half doors
  • Cord & plug
  • Two pair(s) universal bottom support tray slides (one pair at bottom of each compartment). half section)
  • Pad lock hasp

Item No 37 – CARBONATOR

Manufacturer: The Cornelius Company

Model No.: 416424115

Quantity Req'd.: 1

Status: By Product Supplier/Vendor

  • Foodservice Equipment Contractor to provide swirl-type flexible disconnect per specific conditions for this item.
  • Connect to Item 21, Water Treatment System.
  • Foodservice Equipment Contractor to confirm utility requirements and reflect those requirements on the dimensioned rough-in plan.

Item No 38 - BAG N' BOX RACK

Manufacturer: The Cornelius Company

Model No.: 1BI

Quantity Req'd.: 1

Status: By Product Supplier/Vendor

Cornelius Model No. 2BIFJ, Bag-in-Box Inclined Shelf

  • Number of shelves to suit number of flavors.
  • Top shelf.
  • Adjustable leveler for rack.
  • Plastic end caps as required.
  • Connectors for stacking BIB shelves.
  • Carbonator mounting shelf.
  • CO2 cylinder restraint.
  • CO2 cylinder restraining chain.

Item No 39 - FLOOR TROUGH

Manufacturer: Custom Fabrication

Quantity Req'd.: 1

Status: In Contract

IMC/TEDDY Model No. SFT, Shallow Floor Trough

Unit of size and shape as shown on plan. This item to be set and installed by General Contractor. Quarry tile floor finish to be etched, if required, prior to setting food service equipment in place. Provide grating sections of equal size not to exceed 20" long. Provide shop drawings of size and scale outlined in specific conditions.

Options:

  • Grating to be anti-slip, stainless steel.

Item No 40 - ICE STORAGE & TRANSPORT SYSTEM

Manufacturer: Follett Corporation

Model No.: ITS1350SG-60

Quantity Req'd.: 1

Status: In Contract

Options:

  • Partition
  • Set of Ice Totes, with handles, no cover, fits SmartCART 75, poly construction, 25 lb capacity (set of 6)
  • Ice Shovel, heavy duty poly construction
  • SmartCART 240, mobile, insulated, polyethylene, removable lid, 240-lb capacity
  • Ice Paddle, high density poly, 58-1/2" long, for ITS & double door DEV models
  • Ice Scoop, 82 oz
  • Reinforced top (required if icemaker(s) weights exceeds 1,000 lbs, add 2-1/8" to height.

Item No 41 - ICE CUBER