Program Release Information

Program Release Information

CSES ID-No. DLBT1101740EN00

Model: ineo423_363_283

MFP firmware Ver.G00-C8

Subject: ineo423_363_283_Maintenance Release Program (Ver.G00-C8)

2011/08/18

1. Release version and download file name

The newly released program version and download file name is as follows.

[Release version]

Model / Program Name / Current Ver. / New Ver. / Program File Name / Check Sum / Note
ineo423/363/283 / MFP firmware / G00-C2 / G00-C8 / A1UD0Y0-F000-G00-C8.exe / ed31 / OWN
ineo423/363/283 / MFP firmware / G00-C2 / G00-C8 / A1UD0Y6-F000-G00-C8.exe / d43c / Traditional Chinese

ineo423/363/283 MFPController BOOT Program

Product Name / Program Name / Current Ver. / New Ver. / Program File Name / Checksum / Note
ineo423/363/283 / MFP firmware / G00-00 / G00-02 / A1UD0Y0-1E00-G00-02.exe / EBBC

* The Boot Rom-Only FW for “G00-00” is not released.

ineo423/363/283 Scanner Program

Product Name / Program Name / Current Ver. / New Ver. / Program File Name / Checksum / Note
ineo423/363/283 / MFP firmware / G00-06 / G00-09 / A1UD0Y0-0023-G00-09.exe / 0DDA

* The Boot Rom-Only FW for “G00-06” is not released.

[Download File Name]

A1UD0Y0-F000-G00-C8.exe

A1UD0Y0-1E00-G00-02.exe

A1UD0Y0-0023-G8X-09.exe(Card Ver. of a scanner)

->Refer to the revised (*5): It automatically detects CPU and shows each Version.

ineo423/363/283_PRI_ DLBT1101740EN00.doc

2. What changed

2.1. Release of ineo423/363/283 (Maintenance Release Program Ver.G00-C8)

The individual files and the checksum are as follows.

Program Name / File Name / Checksum / Note
BOOT / A1UD0Y0-1E00-G00-02 / EBBC
MFP controller subset / A1UD0Y0-1F00-G00-03 / B268
MFP controller / A1UD0Y0-0100-G00-C8 / 2210
MFP controller system / A1UD0Y0-1000-G00-C8 / -
MFP controller print controller / A1UD0Y0-3000-G00-26 / -
MFP controller print controller font / A1UD0Y0-3F00-G00-01 / -
MFP controller print controller Demo Page / A1UD0Y0-3E00-G00-00 / -
MFP controller MIO / A1UD0Y0-5000-G00-06 / -
MFP controller PSWC / A1UD0Y0-5100-G00-10 / -
MFP controller MIB IF / A1UD0Y0-5200-G00-00 / -
MFP controller IPP IF / A1UD0Y0-5200-G00-00 / -
MFP controller Outside controller IF(*4) / - / -
MFP controller TCP/Socket / A1UD0Y0-6300-G00-21 / -
MFP controller OPEN API / A1UD0Y0-7000-G00-13 / -
MFP controller operation panel / A1UD0Y0-8000-G00-C8 / -
MFP controller PIC / A1UD0Y0-8200-G00-A3 / -
MFP controller CSRC control Body / A1UD0Y0-8300-G00-01 / -
Scanner(*5) / A1UD0Y0-0023-G00-09 / 0DDA
DSC1(*2) / A0P00Y0-8500-G00-01 / 1336
DSC2(*2) / - / -
Printer / A1UD0Y0-0050-G00-11 / 96A9
FAX board controller 1(*2) / A22M0Y0-4000-G00-03 / 03DF
FAX board controller 2(*2) / A22M0Y0-4000-G00-03 / 03DF
Operation panel message data / A1UD0Y0-8100-G00-C2-00 / 688B / OWN
ADF(*2) / A1430Y0-0024-G00-11 / FAD6
Finisher (FS-527)(*2) / A0HR0Y0-0071-G01-07 / D298
Finisher (FS-529)(*2) / A0U70Y0-0071-G01-06 / E843
JS-505(*2) / A0830Y0-0070-G02-03 / F65A
SD(*2) / A10D0Y0-0071-G00-04 / 13C8
OCR Library / A0ED0Y0-B000-G00-0800 / C334
COPY PROTECT(*3) / - / 4152
Movie Data / A1UD0Y0-A000-G00-00

(*2) When unloading disables to download.

(*3) Be sure to see Check Sum of COPY PROTECT on Firmware Update screen after completing to download.

(*4) When unloading disable to indicate ROM version.

(*5) It automatically detects CPU mounted on the MFP board and shows one of the followings.

H8S/2324:A1UD0Y0-0023-G00-09 Check Sum 0DDA

H8S/2325:A1UD0Y0-0023-G80-09 Check Sum 7F0E

H8S/2424:A1UD0Y0-0023-G82-09 Check Sum BA94

H8S/3006:A1UD0Y0-0023-G81-09 Check Sum F469

2.2. What is taken action

2.2-1. The following issues are solved in this firmware.

1.On the MFP with FS527+PK517(2-3 holes) is installed, C11C0 may occur if printing the job with punch.

2.On the MFP with FS-529 is installed, Offset sorting may not be performed correctly.

3.The HDD installation setting is changed from “Installed“ to “Not Installed” automatically. [PEBJHK09005968, PEBJAC10000267, PEBAU_10000182, PEBJTK10001099 etc.]

4. Machine freezes when getting back from sleep [PEBJNG11002599]

5. Machine freezes when making copy / paper is empty.

2.2-2. The following issues are modified in this version.

1. Due to effect of the earthquake in Eastern Japan, the scanner FW is changed because the microprocessor (IC400) on MFP board had been changed.

The Board number for the MFP board mounted with the current microprocessor (H8S/2324) : A1UDH020/A1UDH021

The Board number for the MFP board mounted with the new adopted microprocessor (H8S/2424) :

A1UDH02Y (Blue label is affixed on MFP and Packaging box)

The Board number for the MFP board mounted with the new adopted microprocessor (H8S/2425) :

A1UDH02X (Black label is affixed on MFP and Packaging box)

The Board number for the MFP board mounted with the new adopted microprocessor (H8S/3006) :

A1UDH02W (Blue label is affixed on MFP and Packaging box)

If the scanner FW for the current microprocessor (older than G00-C8) is rewritten to the MFP board mounted with the new adopted microprocessor, “Download N.G” appears only for the scanner FW and if the Main Power SW is turned OFF and ON, C-C152 occurs and MFP hangs up.

Please rewrite the Scanner FW by using Scanner-only FW (A1UD0Y0-0023-G00-09.exe) or the FW (A1UD0Y0-F000-G00-C8.exe) if the above symptom is occurred.

There is no problem even if the new scanner FW is rewritten to the current microprocessor(H8S/2324) on the MFP board using this FW.

The Scanner FW version for the current microprocessor and for the new adopted microprocessor is different.

For the current microprocessor: xxxxxxx-xxxx-G00-09

For the new adopted microprocessor: xxxxxxx-xxxx-G80-09

xxxxxxx-xxxx-G82-09

xxxxxxx-xxxx-G81-09

2. The Boot Rom is changed by revision up (Rev1.1>Rev2.1) of CPU (IC100) on MFP board.

“CPU Rev2.1” label is affixed on MFP board if the revision up CPU (Rev2.1) is mounted on MFP board.

If the current Boot Rom (A1UD0Y0-1E00-G00-02) is rewritten to the MFP board mounted with the revision up CPU (Rev. 2.1), the following symptom occurs.

- The control panel does not light up and MFP hangs up if returning the power save mode or the Sub Power SW is turned OFF and ON.

Please rewrite the Boot ROM by using the Boot Rom-only FW for specific use (A1UD0Y0-1E00-G00-02.exe) or the FW (A1UD0Y0-F000-G00-C8.exe) if the above symptom is occurred.

There is no problem even if the new Boot ROM is rewritten to the current CPU (Rev. 1.1) on the MFP board.

For details about the above issues, please refer to TNI: TNBT1100115EN00

3. Functional restrictions

3.1 Functional restrictions

1. When printing PDF file (A3/A4 mixed original) from Acrobat (Acrobat Reader) Ver.8 from PS driver, all pages are printed on A4 size papers.

[Countermeasure]

Properties of PS driver> Advanced> PostScript Pass through: "Disable"

2. When switching Authentication Method (General Settings) from "ON (MFP)" to "ON (External Server)", user name that was registered on MFP is displayed on the operation panel. If you login to the MFP using this user name, authentication failure occurs.

[Procedure to switch from MFP Authentication to External Server Authentication]

1. Set "General Settings" to "OFF" and clear the user's data.

2. Set "General Settings" to "ON (External Server).

3. When editing or saving a Phone book data (CSV file) using Excel, over 12-digit Fax number is saved as Scientific (e.g.1.23457E+19). (This is a problem on Excel side.)

If you use the Phone book (CSV file) that was edited or saved using Excel, please confirm the Fax number before you send a Fax job.

4. If you print large file from XPS driver, "Connection Timeout" may be indicated when MFP receives the data, and "Deleted Due to Error" may occur. (This is a problem on OS side.)

[Countermeasure]

To avoid this problem, please set the driver to the following condition.

Configure Port (Printer Driver> Properties> Ports)

Protocol > LPR

LPR Setting > LPR Byte Counting Enabled

5. If Original Orientation of application is different from Original Orientation of Driver when printing the job from FAX driver, TX result may be different from preview of Cover Sheet.

Please set Original Orientations of application and Driver in the same direction.

6. When sending a job with the following settings, the job is stamped with black even if you set stamp with color.

- Set “Grayscale” and “Compact PDF” format.

- And set “Stamp Composition” to “Image”. (omit Preset Stamps)

7. After installing Vender, “Group” and “Program” that were registered when uninstalling the Vender are displayed.

*(After installing the Vender, it is impossible to perform new registration of “Group” and “Program”.)

8. In Web Connection, if you click the following menu buttons before the screen is displayed completely, white screen may be displayed.

This symptom occurs in the following screen.

[User Mode]

Job

[Administrator Mode]

Maintenance, System Settings, User Auth/Account Track, Network, Fax Settings

Recovery Method: Click menu button again.

9. In PS driver, when setting the followings at the same time, overlay image is shifted from set Binding Margin value and printed.

(This issue does not occur in PCL and XPS.)

-Booklet

-Overlay

-Binding Margin

* Refer to the Readme.txt file which is included in each driver and application for other functional restrictions.

* Additional memory installation is required when using the following Open API functions.

1) Functions using web browser on MFP.

2) Initial screen customization

4. How to install

4.1. How to install program

Use USB memory to install. For the details, see the Service Manual.

Conditions for USB memory which can be used for updating the firmware are as follows.

- Without security function

- Capacity 1GB to 2GB are recommend

- Compatible with to USB2.0

- Formatted in FAT32 format

4.2. How to check version

[ROM version]:

You can check the ROM version in service mode, "Firmware Version”

For the details, see the Service Manual.

4.3. How to install movie data

Use USB memory to install.

For the details, see the Service Manual.

4.4. Function Version of Printer Driver

Please make sure that “Version3” has been selected.

Select “Version3” in Properties of Printer Driver> Configure> Function Version

* If “Auto” of Acquire Settings is on, Function Version3 is applied to the Printer Driver automatically.

5. Program that recommends applying at the same time

Please refer to the PRI for “DOCUJET 4236/4228 Mass-Production Program (Ver.G00-C0” for details. (DLBT1101200EN)

6. OpenAPI supported function level

The following is OpenAPI supported function level on this firmware.

OpenAPI:

OpenAPI Function Level / 3.5B

Detail:

Auth / 1.0/1.1/2.0/2.5/3.5
Scan to Application / 2.0/2.1/2.2/3.0/3.5
PullPrint / 1.0/1.1/2.0/2.5/3.5
Other A / 1.0/3.5
Job Management / 1.0/3.5
Setup / 1.0/1.1/1.2/1.3/2.0/2.1/2.5/3.5
Web Browser / Auth / 1.0/1.5/3.5
Scan to Application / 1.0/1.1/3.5
PullPrint / 1.0/1.5/3.5
ScrSvr / 1.0/3.5
Launcher / 1.0/3.5

* Company names and product names in this document are the registered trademarks for respective companies.

Konica Minolta Confidential 1/5