FSSI JanSan IPD’s (Motorized Floor Cleaning)
NSN: 7220-00-224-6486
MAT, FLOOR: Rubberized link-type floor mat with the following characteristics:
Material: Rubberized fabric, long link
Length: 50 inches
Width: 24 inches
Thickness: 5/8 inch
Mats without nosing
The floor mats shall contain 75-100% postconsumer content and 85-100% total recovered materials content by weight as specified by the EPA Guidelines for Federal Procurement.
Material: The links shall be made of superimposed layers of rubberized fabric and shall contain not less than three plies of fabric. As an alternate construction, 2 or more ply side wall strips measuring 0.393 ± 0.118 inch in thickness and 0.748 ± 0.078 inch wide, with spacers, cut from truck and passenger tires may be used for the rubberized fabric link. Solid black or alternating side-wall strips of black and white may be used. The links or strips shall be free of objectionable odor and shall contain no material that may stain, damage, or mar the appearance of floors.
Cross wires: The cross wire shall be corrosion resistant or galvanized spring-steel wire. The wire shall be 0.09 inch to 0.13 inch in diameter.
Links: Links may be of any length up to 4 inches as long as the mat remains flexible. The width shall be 0.55 inch. Holes shall be 0.11 inch in diameter. The links shall have line contact with the floor at not less than three approximately equidistant points. The wearing surface of the links shall be corrugated at a right angle to the length of the links.
Color: The mat color shall be naturally produced by the edge surfaces of the rubberized fabric. Either dark or light links may be used in the mat to produce a uniform appearance.
Dimensions: Unless otherwise specified, dimensions listed shall be considered maximum with a minus 3 percent.
Workmanship: The floor mats shall be free from embedded foreign material, cracks, tears, objectionable odor or any other defect affecting appearance or serviceability.
Unit of issue: EA (Each).
NSN: 7220-00-238-8852
MAT, FLOOR: Rubberized link-type floor mat with the following characteristics:
Material: Rubberized fabric, long link
Length: 30 inches
Width: 18 inches
Thickness: 5/8 inch
Mats without nosing
The floor mats shall contain 75-100% postconsumer content and 85-100% total recovered materials content by weight as specified by the EPA Guidelines for Federal Procurement.
Material: The links shall be made of superimposed layers of rubberized fabric and shall contain not less than three plies of fabric. As an alternate construction, 2 or more ply side wall strips measuring 0.393 ± 0.118 inch in thickness and 0.748 ± 0.078 inch wide, with spacers, cut from truck and passenger tires may be used for the rubberized fabric link. Solid black or alternating side-wall strips of black and white may be used. The links or strips shall be free of objectionable odor and shall contain no material that may stain, damage, or mar the appearance of floors.
Cross wires: The cross wire shall be corrosion resistant or galvanized spring-steel wire. The wire shall be 0.09 inch to 0.13 inch in diameter.
Links: Links may be of any length up to 4 inches as long as the mat remains flexible. The width shall be 0.55 inch. Holes shall be 0.11 inch in diameter. The links shall have line contact with the floor at not less than three approximately equidistant points. The wearing surface of the links shall be corrugated at a right angle to the length of the links.
Color: The mat color shall be naturally produced by the edge surfaces of the rubberized fabric. Either dark or light links may be used in the mat to produce a uniform appearance.
Dimensions: Unless otherwise specified, dimensions listed shall be considered maximum with a minus 3 percent.
Workmanship: The floor mats shall be free from embedded foreign material, cracks, tears, objectionable odor or any other defect affecting appearance or serviceability.
Unit of issue: EA (Each).
NSN: 7220-00-254-4240
MATTING, FLOOR (FOR FLOOR/STAIR RUNNER SLIP RESISTANT): Shall be in accordance with Purchase Description 7FXEDM5 dated October 24, 1997, with the following characteristics:
Material rubber or vinyl
Length 25 yards
Thickness 0.125 inches minimum
Width 36.0 inches
Color black
Pattern ribbed (longitudinal corrugation)
Unit of issue - RO (roll twenty five (25) yards in length).
NSN: 7220-00-255-0765
MATTING, FLOOR: Shall be in accordance with MIL-DTL-15562G dated May 31, 1996 with the following characteristics:
Type II: runner type, smooth surface
Length: 25 yards
Thickness: 0.125 inches minimum
Width: 24.0 inches
Color: black
First Article: A first article inspection is required in accordance with paragraph 3.1 of the specification.
EXCEPTIONS TO THE SPECIFICATION:
Paragraph 3.5, Line 2: Delete “plus or minus 3.0 yards.” and add: “minus 1/2 yard, any plus tolerance acceptable.”
Paragraph 3.5 Add “All rolls shall be tagged showing the exact number of yards in that roll.”
Unit of issue - RO (roll twenty five (25) yards in length).
NSN: 7220-00-457-6046
MAT, FLOOR: Floor mat with the following characteristics:
Material: - Polyvinylchloride (with cleats)
Shape: - With single lip
Lip location/dimension - Lip centered on the width dimension
- 20.00 inches wide
- 10.00 inches deep
Length: - 48.0 inches
Width: - 36.0 inches
Thickness: - 0.145 inches
Colorless: – Transparent
NISH P/N 7220-00-457-6046
Unit of issue – EA (Each).
NSN: 7220-00-457-6054
MAT, FLOOR: Floor mat with the following characteristics:
Material : Polyvinylchloride (with cleats)
Shape: With single lip
Lip location/
Dimension: Lip centered on the width dimension
20.0 inches wide
10.00 inches deep
Length: 53.0 inches
Width: 45.0 inches
Thickness: 0.145 inches
Colorless: Transparent
NISH P/N 7220-00-457-6054
Unit of issue – EA (Each).
NSN: 7220-00-753-2981
MATTING, FLOOR (FOR FLOOR/STAIR RUNNER SLIP RESISTANT): Shall be in accordance with Purchase Description 7FXEDM5 dated October 24, 1997, with the following characteristics:
Material: rubber or vinyl
Length: 10 yards
Thickness: 0.125 inches minimum
Width: 24.0 inches
Color: black
Pattern: ribbed (longitudinal corrugation)
Unit of issue - RO (roll ten (10) yards in length).
NSN: 7220-00-965-4769
MATTING, FLOOR (FOR FLOOR/STAIR RUNNER SLIP RESISTANT): Shall be in accordance with Purchase Description 7FXEDM5 dated October 24, 1997 with the following characteristics:
Material: rubber or vinyl
Length: 25 yards
Thickness: 0.188 inches minimum
Width: 24.0 inches
Color: black
Pattern: ribbed (longitudinal corrugation)
Unit of issue - RO (roll twenty five (25) yards in length).
NSN: 7220-01-056-1944
MATTING, FLOOR: Shall be in accordance with MIL-DTL-15562G dated May 31, 1996 with the following characteristics:
Type III: mat, runner type, raised diamond pattern surface
Length: 25 yards
Thickness: 0.188 inches minimum
Width: 36.0 inches
Color: green
Exceptions to the Specification:
Paragraph 3.5 Line 2 Delete: “plus or minus 3.0 yards.” and add “minus 1/2 yard, any plus tolerance acceptable.”
Paragraph 3.5 add:“All rolls shall be tagged showing the exact number of yards in that roll.”
Unit of issue - RO (roll twenty five (25) yards in length).
NSN: 7220-01-305-3062
MAT, FLOOR: Floor mat with the following characteristics:
Material: Polyvinylchloride (with cleats)
Shape: With single lip
Lip location/dimension:
Lip centered on the width dimension:
20.00 inches wide
10.00 inches deep
Length: 53.0 inches
Width: 45.0 inches
Thickness: 0.220 inches
Colorless: Transparent
NISH P/N 7220-01-305-3062
Unit of issue – EA (each).
NSN: 7220-01-411-1515
MAT, FLOOR: Shall be SKILCRAFT/3M Nomad Mats, P/N 26445, 3M™ Nomad™ Scraper Matting 6050, with the following characteristics:
Size: 3 ft. X 5 ft.
Color: Slate
UPC: 500-48011-26445-0
Unit of issue - EA (Each).
NSN: 7220-01-411-2979
MAT, FLOOR: Shall be in accordance with SKILCRAFT/3M Nomad Mats P/N 26187, 3M™ Nomad™ Scraper Matting 6050, with the following characteristics:
Size: 3 ft. X 5 ft.
Color: Dove
UPC: 000-48011-26187-4
Unit of issue - EA (Each).
NSN: 7220-01-411-2980
MAT, FLOOR: Shall be in accordance with SKILCRAFT/3M Nomad Mats P/N 26189, 3M™ Nomad™ Scraper Matting 6050, with the following characteristics:
Size: 4 ft. X 6 ft.
Color: Dove
UPC: 000-48011-26189-8
Unit of issue - EA (Each).
NSN: 7220-01-471-0913
MAT, FLOOR: Shall be in accordance with East Texas Lighthouse for the Blind P/N NIB-0017, or equal, with the following characteristics:
Material: Polyvinylchloride
Form: With single lip (25.0 inches X 12.0 inches)
Finish: Pressure embossed one side, smooth on the other side.
Length: 53.0 inches
Thickness: 0.110 inches, minimum
Width: 45.0 inches
Colorless: Transparent
Unit of issue - EA (Each).
NSN: 7910-00-526-1959
CLEANER, VACUUM, ELECTRIC: Shall be an explosion proof and dust ignition proof, wet/dry, electric vacuum cleaner with filter, designed for use in Class I, Group D, and Class II, Groups E, F and G atmospheres, as defined in NFPA 70, National Electric Code. Vacuum cleaner shall be UL listed and have the following characteristics:
Characteristic: / Minimum Requirement:Stainless Steel tank / 22 gauge
Tank Size / 15 gal
Wet capacity / 12 gal
Dry capacity / 10 gal / 1.5 cu.ft.
Voltage / 115 V
Airflow / 120 cfm
Waterlift / 69”
Power cord / 14/3 50’
Filter (polypropylene cloth
or equivalent) / 3-5 cfm, 48 x 24 count weave,
12.5 oz /sq yd 13.3 ply
Caster/wheel size / 3” dia
Owner’s / Operating manual / Included
Tool Kit(*): / Included
Hose / 1-1/2” 10’
Round brush / Included
Crevice tool / Included
Extension wand / Included
Conical nozzle / Included
Floor tool / Included
Squeegee / Included
* At the supplier’s option, additional tools may be included in the tool kit.
Unit of issue: EA (Each). (One (1) complete system to a package).
NSN: 7910-00-550-9111
CLEANER, VACUUM, ELECTRIC: Shall be in accordance with the following requirements and characteristics:
Type: Wet and dry pickup
Size: 10 gallons (37.9 L)
Voltage: 120 Vac, 60 Hz, single phase
Fire and Casualty Hazards: Vacuum cleaners shall meet the applicable requirements of UL 1017. Evidence of conformance with UL standards shall be a UL label(s) or listing mark(s), or a certified test report (based on tests conducted within the past two years) from an independent testing laboratory acceptable to the Government, indicating the vacuum cleaner has passed all applicable tests.
General Construction:
Each cleaner shall be complete, lubricated, and ready to operate (minor assembly is permitted). The design shall be simple in construction, shall permit easy accessibility to component parts for cleaning, inspection, adjustment, or replacement, and shall provide reliable operation. Similar component parts and assemblies of identical model number cleaners shall be fully interchangeable. Interchangeability shall not require alteration or modification.
Wet pickup: Cleaners with wet pickup capability shall be provided with an automatic shutoff mechanism and accessories required to convert the machine from wet to dry pickup.
Power switch and controllers: Each cleaner shall be provided with a quick make and break type power switch.
Power cord: The power cord assembly shall have three conductors and a three-prong attachment plug, and shall have a minimum length of 24 feet (7.32 m). The cord length shall be measured from the point of exit from the machine to the point of entry into the attachment plug. The end user shall be responsible for providing and installing an attachment plug in accordance with local codes and insurance requirements.
Power cord storage: Each cleaner shall be provided with a means for coiling, wrapping, or otherwise storing the power cord when the cleaner is not in use.
Filtration system: The filtration system shall consist of a primary filter, wet pickup separator, and tank assembly. When employed for dry pickup, the primary filter shall be employed. When converted for liquid retrieval, the separator and automatic shutoff assembly shall take the place of the primary filter.
Dry pickup: The primary filter shall filter particulate matter 1 mm and larger and shall retain this matter for easy disposal. This filter may be disposable. No ingested unfiltered air shall be exhausted from the cleaner.
Wet pickup: The machine shall be equipped with an effective separator, which will prevent liquids and non-particulate solid objects from passing through to the vacuum producer. An automatic shutoff assembly shall be provided which interrupts the air intake or power to the cleaner when the minimum liquid capacity is reached.
Tank: The tank shall be of stainless steel, plastic, or shall have a durable interior epoxy coating. The tank shall hold the minimum liquid capacity for the size specified before the shutoff mechanism activates and shall have a drain valve.
Mobility: The cleaner shall have a bearing-equipped wheeled chassis or bearing-equipped self-lubricating polymeric wheels mounted on the tank to provide mobility. Wheels and casters are acceptable in any combination. The cleaner shall be equipped with a handle assembly suitable for use in cleaner movement. The cleaner shall be free-wheeling and easily transportable.
Attachments: The cleaner shall be furnished with one 11-inch (279 mm) minimum length carpet tool, one 14-inch (356 mm) minimum length bare floor tool, one 14-inch (356 mm) minimum length squeegee tool, one 9-inch (229 mm) minimum length crevice tool, one 48-inch (1220 mm) minimum length wand assembly, and one 1-1/2-inch (38.1 mm) minimum inside diameter, 120-inch (3050 mm) minimum length hose assembly. The unit shall have an automatic shutoff assembly, and any necessary attachments for conversion from dry to wet pickup.
Tool construction: The attachments for all cleaners shall be fabricated from a nonferrous alloy or a suitable synthetic material. Metal tools shall be suitably plated or finished to resist corrosion and prevent marking. Bristles, squeegee strips, etc., used in the tools shall be replaceable.
Hose construction: The hose shall be fabricated from non-marking materials impervious to attack from common cleaning solutions. A swivel coupling shall be provided on the hose end attaching to the cleaner. The hose shall be able to withstand a minimum compressive load of 150 lb (667 N) applied to any portion of the hose no closer than 12 inches (305 mm) from any fitting by means of parallel flat surfaces having lengths of not more than 3 inches (76.2 mm) parallel to the axis of the hose for not less than 2 minutes. The compressive load shall cause no rupture of any portion of the hose and the resulting hose diameter shall not differ more than 1/16 inch (1.59 mm) from the diameter prior to the compressive load.
Couplings: The engaged wand, hose, and tools shall be able to withstand a tensile force of 25 lb (111 N) for 2 minutes at each coupling without separation. Couplings shall engage and release satisfactorily before and after being subjected to the 25-lb (111 N) tensile force.