Chemistry: Density Determination Lab
I. IntroductionDO NOT WRITE ON THIS LAB
The study of chemistry involves not only observing changes in matter, but also measuring those changes. In fact, most chemical principles cannot be fully understood without obtaining and analyzing some quantitative data. The techniques of data collection, data analysis, and measurement are an important part of chemistry.
Careful attention should be given to the degree of uncertainty in your measurements. Use only those digits that are significant in your calculations in this experiment and in all other quantitative experiments. The precision of your methods can be reported with your results in terms of percentage error. The percentage error in calculations and measurements is a comparison of the differences between experimental results and theoretical values calculated as a percentage. Percentage error can be determined as follows:
% error = ( experimental result - theoretical value ) x 100
theoretical value
A useful way of comparing two substances is to compare their densities. By carefully measuring the mass and volume of a substance, its density can be calculated as follows:
Density = mass
volume
In conducting this experiment, you will make several mass and volume measurements to determine the density of water, known solid, and unknown solution of acetone/water. You will then find the precision of your measurements by calculating the percentage error in your results.
Objectives:
In this experiment you will determine the density of different substances from mass and volume measurements and calculate the percentage error in your results.
Equipment:50 mL graduated cylinder, 10 mL graduated cylinder, electronic balance, aluminum, nickel, acetone solution with unknown concentration.
Procedure:
I. Density of Water
1.Measure the mass of a 10 mL graduated cylinder and record your measurement in the data table.
2. Add 8.0 mL of water to the graduated cylinder. Record the total mass of the cylinder and water in the data table.
3. Read the volume of the water to the nearest 0.1 mL. Your eye should be at the same level as the bottom of the meniscus when you read the cylinder markings. Record the water volume in the data table.
4. Calculate the density of water to the correct number of significant figures. Record the density in the data table.
II. Density of a solid
1. Choose aluminum (20 pieces) or nickel (15 pieces), mass, and record the measurement in the data table.
2. Fill a 50 mL graduated cylinder with 25 mL of tap water, read the volume to the nearest mL, and record the water volume in the data table.
3. Carefully immerse the solid in the water in the cylinder without splashing. Measure the new volume to the nearest mL and record in the data table.
4. Pour the water into the sink & put the solid sample in the aluminum or nickel tray designated by your teacher. Do not return solids to the original container. Do not mix aluminum and nickel!
5. Calculate the density of the solid to the correct number of significant figures. Record the density in the data table.
III. Finding the concentration of a solution of acetone & water using density.
1. Obtain an unknown solution of acetone & water. Record the unknown in the data table
2. Place a 10 mL graduated cylinder on a balance that has been tarred. Record the mass in the data table.
3. Transfer about 8 mL of solution into the graduated cylinder. Record the mass in the data table
4. Remove the graduated cylinder from the balance and place on the lab table. Record the volume of the solution in
the cylinder to the correct number of significant figures.
5. From the mass and volume, calculate the density of your solution. Record this on the data table
6. Interpolate the density of your unknown solution by using the graph below.
IV. Lab Safety
Be sure all glassware is washed and dried before placing it back. The specific hazard information for acetone is below:
Health Rating: 1 - Slight
Flammability Rating: 4 - Extreme (Flammable)
Reactivity Rating: 2 - Moderate
Contact Rating: 1 - Slight
Lab Protective Equip: GOGGLES; LAB COAT; VENT HOOD; PROPER GLOVES; CLASS B EXTINGUISHER
Storage Color Code: Red (Flammable)
Chemistry: Density Lab Names:
Period:
Data Table
- Be sure you record the correct number of significant figures for each measure (1 place past level of accuracy)
I. Density of waterArea for Showing your calculations.
graduated cylinder______g
cylinder + water______g
mass of water______g
volume of water______mL
density of water______g/mL
II. Density of a solid
Name of solid ______
Mass of solid______g
volume water______mL
volume water + solid______mL
volume of solid______mL
density of solid ______g/mL
III. Concentration of Unknown solution using density
Volume of solution ______mL
Mass of solution______g
Density of solution______g/mL
From the graph above and your calculated density, find the % concentration of the acetone solution
% Concentration of acetone solution ______%
IV. Theoretical Density Values
Density water ______g/mL – (find the defined density of water from your notes or book)
Density solid ______g/mL – (from your periodic table)
V. Conclusions
Answer the following questions on the back side of this paper.
1.Describe briefly the method that is used to determine the volume of a solid.
2.Describe briefly the method that is used to find the mass of a liquid.
3.Calculate the percentage error for water & the solid. Remember significant figures and units!
Show your work!
4.What were the major sources of error with the methods of measuring density that you used?
5.The method used to find the density of the unknown solid will not work for all solids. Why Not?