Outdoor Stainless Steel Pressurized Pan-Tilt-Zoom Dome High Definition Ip Camera

Outdoor Stainless Steel Pressurized Pan-Tilt-Zoom Dome High Definition Ip Camera

[Project No.][Project Name]

[Date][Project Location]

SECTION 28 23 29

OUTDOOR STAINLESS STEEL PRESSURIZED PAN-TILT-ZOOM DOME HIGH DEFINITION IP CAMERA

MOOGEXSP7C2-3

DIVISION 28- ELECTRONIC SAFETY AND SECURITY

28 20 00 ELECTRONIC SURVEILLANCE

28 23 00 VIDEO SURVEILLANCE

28 23 29 VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS

SECTION 28 23 29

OUTDOOR STAINLESS STEEL PRESSURIZED PAN-TILT-ZOOM DOME HIGH DEFINITION IP CAMERA

MOOGEXSP7C2-3

ARTICLEI. – GENERAL

1.01SUMMARY

  1. Section includes a stainless steel pressurized outdoor pan-tilt-zoom dome high definition IP video camera

B.Product

1.Ruggedized, stainless steel, and pressurized High Definition IP video camera (“outdoor IP dome camera”) with outdoor dome housing with integral pan-tilt-zoom mechanism

  1. Related Requirements

1.28 00 00 – Electronic Safety and Security (Division 28)

a.28 05 00 – Common Work Results for Electronic Safety and Security

b.26 06 00 – Schedules for Electronic Safety and Security

c.26 08 00 – Commissioning of Electronic Safety and Security

d.28 23 23 – Video Surveillance Systems Infrastructure

e.28 23 26 – Video Surveillance Remote Positioning Equipment

1.02REFERENCES

  1. Abbreviations and Acronyms

1.CCTV – Closed Circuit Television

2.NEMA – National Electrical Manufacturers Association

3.PTZ – Pan-tilt-zoom

  1. Reference Standards

1.Federal Communications Commission (FCC), Code of Federal Regulations,
Title 47, Part 15

2.European Union – EN60950 – Safety of Information Technology Equipment (ITE)

3.European Union – EN 62262:2002 – Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK-10)

4.IEC 60721 – Classification of Environmental Conditions

5.IEC 60068 – Environmental Testing

6.UL – ANSI/ IEC60529 – Degrees of Protection Provided by Enclosures

7.International Electrotechnical Commission (IEC) – Ingress Protection Rating IP67

8.NEMA – TS2

9.Institute of Electronic and Electrical Engineers (IEEE) 802.3 standards

10.International Telecommunication Union (ITU) – H.264 Advanced video coding for generic audiovisual services

11.ISO/IEC 14496 – MPEG-4

12.ISO/IEC 14496 – 10 – MPEG-4, Part 10 (H.264)

13.ISO/IEC 10918 – JPEG

1.03SUBMITTALS

  1. Product Data
  2. Manufacturer’s printed or electronic data sheets
  3. Manufacturer’s installation and operation manuals
  4. Warranty documentation

1.04QUALITY ASSURANCE

  1. Qualifications

1. The outdoor IP dome camera, including housing, shall be manufactured in the United States, per ISO 9001 certified procedures

2. Manufacturer of outdoor IP dome camera shall have a minimum offiveyears’ experience of successful manufacture and installation of systems equivalent in function to the system proposed herein

3. Installation contractor shall be factory authorized to install, service and maintain theoutdoor IP dome camera by the system manufacturer

4. Product must be Made in America and meet the requirements of the Buy American Act;Section 1605 of the American Recovery Reinvestment Act (ARRA)

1.05DELIVERY, STORAGE AND HANDLING

  1. Delivery, storage, and handling of the outdoor IP dome camera shall be in accordance with the manufacturer’s recommendations
  2. The manufacturer’s ordering instructions and lead-time requirements shall be followed to avoid delivery and installation delays

1.06WARRANTY

  1. Manufacturer shall provide a limited warranty for the outdoor IP dome camera to be free from defects in material or workmanship for a minimum period of one year
  1. All warranty repairs of equipment shall be performed by manufacturer at factory location and shall not be performed at repair facilities outside of the continental United States, nor at any third party repair companies

1.07APPROVALS

A. FCC, CE, REACH, RoHS, UL, cUL

ARTICLE II. – PRODUCTS

2.01EQUIPMENT

A.Manufacturer:Moog

3650 Woodhead Drive

Northbrook,IL60062-1895USA

Phone +1 (847) 498.0700

Fax +1 (847) 498.3658

B.Model: EXSP7C2-3

C.Substitutions: Not Permitted

D.All units shall be supplied from a single manufacturer

2.02 DESCRIPTION

A.The stainless steel pressurized outdoor pan-tilt-zoom dome high definition IP video camera (“stainless steel pressurized IP dome camera”) shall be an integrated ruggedized and pressurized outdoor dome housing with integral pan-tilt-zoom mechanism and high definition IP video camera

B.Housing

1. The stainless steel pressurized IP dome camera housing shall be constructed of .06” thick 316L stainless steel with a nylon optical dome.

2. The stainless steel pressurized IP dome camera shall include a 316SS sunshield

3. The stainless steel pressurized IP dome camera housing shall be IP 67 rated, designed to withstand dust, water, and pollution intake

4. The stainless steel pressurized IP dome camera housing shall be capable of pressurization and contain both Schrader and 5-7 psi pressure relief valves and shall be capable of maintaining constant pressure within the inner housing area

5. The stainless steel pressurized IP dome camera housing shall contain an integral heater/blower

C.Camera Module

  1. Image Sensor: 1/2.8-type Exmor CMOS
  2. Horizontal viewing angle: 59.5° (wide end) to 2.1° (tele end)
  3. Image Resolution: 1920 x 1080, 1280 x 720, 720 x 480, 720 x 576, 640 x 360
  4. Day/Night Operation: Adjustable (Auto, Color and Mono Modes), removable IR cut filter
  5. Maximum Lens Aperture shall be a minimum of f/1.6 (wide) to f/4.7 (tele)
  6. OpticalZoomRange shall be a minimum of 30X, 4.6mm to 138.0mm
  7. Minimum ObjectDistance: 10mm
  8. The shutter speed shall be automatic or user selectable
  9. Selectable shutter speeds shall be from 1/1 to 1/10,000, total 22 steps
  10. Auto Iris: Selectable auto/manual; Iris shall automatically adjust to compensate for changes in scene illumination
  11. Sensitivity: Scene Illumination shall be a minimum of F1.6 @ 50% Video

a. Less than 1.7 lx (F1.6, 50 IRE), 0.5 lx in High Sensitivity Mode

2.03 PAN-TILT POSITIONING DRIVE

A. Construction

1.The pan-tilt-zoom shall be constructed of aluminum and shall contain belt driven .9° stepper motors and precision ball bearings with permanently lubricated bushings

2.The pan-tilt positioning drive shall have a quick release plate, held by one thumb screw. If this thumb screw is removed the positioner will quickly drop out for shipping

3.The pan-tilt positioning drive, at no time, shall be susceptible to damage or warping due to heat from the internal heating unit, nor shall any of the enclosure incorporate additional plastic heat shields to create a barrier between the heater and the pan-tilt device

B. Performance

1.Pan Movementshall be a minimum of 360°continuous rotation

2.Tilt Movementshall be a minimum of 0° to 95° above horizon tilt

3.Pan speed shall be a minimum of 80° per second

4.Tilt speed shall be a minimum of minimum 34° per second

5.Minimum preset speed/auto pan shall be a minimum of 120° per second

6.Preset position accuracy shall be a minimum of +/- 0.2° precision

7.Variable speed pan-tilt ranges shall be based off of zoom position

2.04 H.264/MJPEG ENCODING ENGINE

A.Video Encoding: H.264 (High, Main, and Baseline Profiles) and MJPEG standards

B.Video Streams: Two configurable streams; user selectable (1) H.264 stream and (1) H.264 or MJPEG stream

C.Video Stream Configuration Properties:

1.Stream Settings: H.264 or MJPEG

2. Image Resolution: H.264: 1080p, 720p; H.264 or MJPEG: D1, 4CIF, VGA, 2CIF, CIF

3.Streaming Mode: Variable Bit Rate (VBR), Motion Adaptive Bit Rate or Constant Bit Rate (CBR)

4.Image Settings: Wide dynamic range (WDR), manual shutter time, compression, color, brightness, sharpness, white balance, exposure control, exposure zones, backlight compression, fine tuning of behavior at low light, rotation, text and image overlay, privacy masks, image freeze on PTZ

5. Frame Rate: 60fps (max resolution 720p), 30fps (max resolution 1080p), 15, 7, 4, 2, 1

D.Connection Types: Uni-cast or multi-cast

E.Data Rate: Adjustable from 64Kb/sec to 6Mb/sec (requires less than 1 Mbps @4CIF/30fps)

F.IPDPS Video Latency: <250ms

G.Network Protocol Layers: RTP, RTSP, UDP, TCP, IPv4, IPv6, HTTP, IGMP, ARP, DHCP, DNS, ICMP

H.Streaming Protocols: RTP, HTTP

I.Management Protocols: RTSP, HTTP, HTTPS, Bonjour, NTP, Telnet, FTP, SNMP

J.Access Control: SSL, Basic and Digest Authentication

K.On-board recording: Internally accessible micro-SDHC interface (32GB max)

L.Software/Firmware Update: Fault tolerant, remote accessible

M.Alarm Events: Triggered by external input or internal event monitoring

2.05AUDIO

A.Standards: Uncompressed PCM High-fidelity AAC-LC G.711

B.Full Audio-Synchronization

C.Audio/Video Buffering: Recorded ASF files to micro-SDHC

2.06ON-SCREEN DISPLAY

A. The stainless steel pressurized IP dome camerasystem shall provide on-screen display (OSD) generator supporting the following capabilities:

1.Provide on-screen display elements as defined below at a minimum; Up to three
on-screen display elements shall be selectable for inclusion in the camera’s two video streams

a.Camera title [20 characters]

b.Time/Date display

c.Preset location [20 characters]

d.Pan-tilt-zoom position

e.Open character [20 characters per zone]

f.Logo Display [96 x 96 pixels maximum]

B.The on-screen display elements shall display on top or bottom of image, displayed on the right hand side of video

C.The Logo element shall display on top or bottom of image, displayed on the left hand side of image

2.07 EVENT MANAGEMENT

A.Event Triggers

1.External Alarm Input

2.User Command

3.Timer / Schedule

B.Event Actions

1.Activate Alarm Output

2.Capture/FTP image snapshot

3.Email notification

4.Activate Preset Position

C.General Purpose Alarm Input

1. Sensor Input: (1) dry contact

2.08 COMMUNICATION PROTOCOLS AND FORMATS

A. The stainless steel pressurized IP dome camerasystem shall include standardized interoperability withthe Genetec API for Genetec Omnicast Software and the Physical Security Interoperability Alliance (PSIA) interface for the Milestone XProtect Software and On Net Surveillance Systems (ONSSI) Ocularis Software.

2.09 MAINTENANCE FUNCTIONS

A. The stainless steel pressurized IP dome camera system shall support maintenance features as defined below;

1.The camera system shall support querying of camera parameters via the Ethernet connection. The camera parameters shall consist of the following items

a.Serial number

b.Software revision

c.Assembly date

d.Camera Model Number

2.Camera System Reset

3.Save and Restore camera system start-up configuration

4. Non-volatile memory in case of hard reset or power outage

5.Remote Software Upload/Updates via Ethernet

6.Camera Device Auto Discovery of IP address

7.Camera System Auto Re-connect

2.10 IP MANAGEMENT

A. The stainless steel pressurized IP dome camera system shall provide at minimum the following network configuration properties;

1.IP Configuration: DHCP or Static IP address entry

2.Net mask address entry

3.Gateway address entry

4.Domain name entry

5.DNS server entry

2.11 POWER INPUT

A. Electrical–The stainless steel pressurized IP dome camera system shall be powered by 24Vac, with a maximum power consumption, including heater/blower, of 80W; or, exclusive of heater/blower, 24 W

2.12 LIGHTNING AND SURGE PROTECTION

A. The stainless steel pressurized IP dome camera system must be equipped with anti-surge protection components and circuitry for video power, data and network that guard against voltage spikes and/or surges. The anti-surge equipment must safely detect and clamp both voltage and current spikes and effectively divert them away from the camera and other sensitive electronics in the camera system

2.13 MECHANICAL

Dimensions14.3"x11.3"x11.3" (364x288x288mm)

Dome OptiClear anti-corrosive coated nylon (IK-10 rated)

Mount / BracketMachined and cast 316L stainless steel

Net Weight16 lb (7.3 Kg) (with sunshield)

Construction BodyHigh-impact, corrosion resistant and passivated 316L stainless steel
Schraeder valveNitrogen input (Pressurized models)

Pressure relief valve5 psi (Pressurized models)

Power Connector16 pin hermetically sealed weatherproof non-corrosion type or equal, or contractor requested

Shipping WeightNo more than 25 lb (11.4 Kg) (with sunshield)

2.14 ENVIRONMENTAL

A. The stainless steel pressurized IP dome camera system shall fully comply with and include independent laboratory test results confirming compliance with the following environmental operating conditions;

1.Temperature:-58°F to 165°F (-50°C to 74°C) tested across low and high voltage ranges per NEMA-TS2 paragraphs 2.1.5 and 2.1.5.1

2. Heater Operation

i. Activation 60°F, +/- 8° (15°C, +/- 8°)

ii. De-activation 80°F, +/- 8° (27°C, +/- 8°)

3.Vibration: Per NEMA-TS2 paragraphs 2.1.9, 2.2.8, 5-30Hz sweep @ 0.5g applied in each of 3 mutually perpendicular planes

4. Shock: Per NEMA-TS2 paragraphs 2.1.10, 2.2.9, 10g applied in each of 3 mutually perpendicular planes

5. Ingress Protection Rating: IP67

6.External Icing: Per NEMA-TS2 250-2003, paragraphs 5.6

7.Corrosion Protection: Per NEMA 250-2003, paragraphs 5.10

8.Humidity: 0-100% N.C per MIL-E-5400T, paragraphs 3.2.24.4

  1. Standards: IP, ASTM, NEMA
  2. Windload: 150 MPH (240kph) sustained winds
  3. Impact Rating: IK-10
  4. Effective Projected Area (EPA): 110 square inches

2.15 CERTIFICATIONS AND RATINGS

A. Certifications and Ratings (IP/NEMA rating)

1. IP67 / NEMA 4X

2. CE (Pending)

3. CUL (Pending)

4. RoHS

5. UL (Pending)

6. WEEE

7. REACH

8. IK-10

9. NEMA TS-2

2.16 OPTIONS

A. The manufacturer shall make available the following options to support the stainless steel pressurized IP dome camera system:

1.Nitrogen fill kit for pressurized housing, including regulator valve and fill tank

2.Rugged cast aluminum power box with 120/240Vac power supply input and 24Vac at
96W output

3.Heavy Duty 316SS Stainless Steel Wall Mount

2.17 SOURCE QUALITY CONTROL

  1. Tests and Inspections
  2. A test report shall be submitted to indicate that each system was tested successfully in a factory system test to meet manufacturer’s published specifications

ARTICLE III. – EXECUTION

3.01INSTALLERS

  1. Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes
  2. The Contractor’s installers and technicians shall be factory authorized to install, service and maintain the system

3.02

PART 2

2.01

2.02INSTALLATION

  1. The stainless steel pressurized IP dome camera system shall ship from the factory fully assembled, tested and ready for installation and use
  2. Before permanent installation of the system, the system and interconnected components and cables shall be staged on-site to verify that all are in good working order
  3. Care shall be exercised to select suitable hardware to install the unit, taking into account both the composition of the mounting surface and the weight of the unit

3.03SUPPORT

A. The stainless steel pressurized IP dome camera system shall be supported by U.S. technical assistance program from the manufacturer and local technical assistance program from a certified and trained professional services company in the country in which the system is installed

END OF SECTION

Rev 02242017

[Author Name]

[File Name] Outdoor Stainless Steel Pressurized Pan-Tilt-Zoom Dome High Definition IP Camera

Top View