MCSA 70-410 Cert Guide R2: Installing and Configuring Windows Server 2012 R2

First Edition

Copyright © 2015 Pearson IT Certification

ISBN-10: 0-7897-4880-0

ISBN-13: 978-0-797-4880-5

Warning and Disclaimer

Every effort has been made to make this book as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an "as is" basis. The author and the publisher shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this book or from the use of the CD or programs accompanying it.

When reviewing corrections, always check the print number of your book. Corrections are made to printed books with each subsequent printing.

First Printing: August 2014

Corrections for November 17, 2015

Pg / Error – Fifth Printing / Correction
CD / Appendix B, Page 3, Table 1-3, Second Description
Reads:
Orovides services for sending and receiving faxes. / Should read:
Provides services for sending and receiving faxes.


Corrections for September 9, 2015

Pg / Error – Fifth Printing / Correction
451 / Chapter 10, First Bullet Point, First Sentence
Reads:
§  fd12:cde6:1208:9::f92b: This is a unique local address in which the first 7 bits are all 1s; the eight bit is also 1, which is the local (L) flag. / Should read:
§  fd12:cde6:1208:9::f92b: This is a unique local address in which the first 6 bits are all 1s; the eight bit is also 1, which is the local (L) flag

Corrections for July 2, 2015

Pg / Error – Fourth Printing / Correction
122 / Chapter 4, Question 1 Answers
Reads:
a.  SMB Share-Quick
b.  SMB Share-Advanced
c.  SMB Share-Application
d.  NFS Share-Quick
e.  NFS Share-Advanced / Should read: (Remove Bold Print)
a.  SMB Share-Quick
b.  SMB Share-Advanced
c.  SMB Share-Application
d.  NFS Share-Quick
e.  NFS Share-Advanced
123 / Chapter 4, Question 5 Answers
Reads:
a.  Only the files and programs that users specify with be available offline
b.  Enable BranchCache
c.  All files and programs that users open from the shared folder are automatically available offline
d.  Optimize for performance / Should read: (Remove Bold Print)
a.  Only the files and programs that users specify with be available offline
b.  Enable BranchCache
c.  All files and programs that users open from the shared folder are automatically available offline
d.  Optimize for performance
124 / Chapter 4, Question 9
Reads:
9. You have created a shared folder named Documents on your Windows Server 2012 R2 computer, which is a member server in your company's AD DS domain. You have assigned the Engineers global group the Full Control NTFS permission to this share. In addition, you have assigned the Interns group the Read permission to a subfolder of the Documents folder that is named Specifications. You do not want the members of the Interns group to be able to modify this folder. What should you do? / Should read:
9. You have created a shared folder named Documents on your Windows Server 2012 R2 computer, which is a member server in your company's AD DS domain. You have assigned the Engineers global group the Full Control NTFS permission to this share. In addition, you have assigned the Interns group the Modify permission to the share and all sub folders. You need to ensure that Interns are not able to modify contents of a subfolder named Specifications. What should you do?
145 / Chapter 4, First Full Paragraph
Reads:
When you enable Offline Files, this feature makes anything you have cached from the network available to you. It also preserves the normal view of network drives, and so on, as well as shared folder and NTFS permissions. When you reconnect to the network, the feature automatically synchronizes any changes with the versions on the network. Also, changes made to your files while online are saved to both the network share and your local cache. / Should read:
When you configure Offline Files, this feature makes anything you have cached from the network available to you. It also preserves the normal view of network drives, and so on, as well as shared folder and NTFS permissions. When you reconnect to the network, the feature automatically synchronizes any changes with the versions on the network. Also, changes made to your files while online are saved to both the network share and your local cache.
151 / Chapter 4, Figure 4-17, Value Column
Reads:
1 / Should read:
Latency=1
164 / Chapter 4, Table 4-8, Option, Second Row
Reads:
Permissions for Authenticated Users / Should read:
Permissions for [Selected User/Group]
223 / Chapter 5, First Paragraph, Last Two Sentences
Reads:
To configure printer pooling, specify a different port for each print device in the printer pool. Then select the check box labeled Enable printer pooling and click OK. / Should read:
To configure printer pooling, select the check box labeled Enable printer pooling. Specify a different port for each print device in the printer pool, and then click OK.
248 / Chapter 6, Second Note
Reads:
NOTE To confirm WinRM functionality, use the Test-WSMan [remote computer] command / Should read:
NOTE To confirm WinRM functionality, use the Test-WSMan [remote computer] command. Test-WSMAN may also be used via PowerShell.
248 / Chapter 6, Add Third Note After Second Note / Note to add:
NOTE WINRS may also be configured via Group Policy in larger deployments.
248 / Chapter 6, Third Bullet Point / Move Third Bullet Point to First Bullet Point
256 / Chapter 6, Paragraph under Enabling Remote Desktop Using Server Manager
Reads:
As with previous editions of Windows, Remote Desktop for Administration is a useful tool. When enabled and authorized through the Firewall, clients can connect to a Full GUI installation using the Remote Desktop Protocol (RDP) over TCP 3389. A Remote Desktop Connection client (mstsc.exe) is included in current operating systems today. Microsoft also provides a Remote Desktop MMC snap-in that allows you to create a list of servers where you can simply double click on the specific server to connect via RDP. / Should read:
As with previous editions of Windows, Remote Desktop for Administration is a useful tool. When enabled and authorized through the Firewall, clients can connect to a Full GUI installation using the Remote Desktop Protocol (RDP) over TCP 3389. A Remote Desktop Connection client (mstsc.exe) is included in current operating systems today. Legacy Windows 7 clients can still use the Remote Desktop MMC Snap-in to manage multiple servers. For anyone using System Center, Microsoft has provided a Remote Desktop Services Management pack that helps administrators manage multiple servers remotely
282 / Chapter 7, Question 4
Reads:
4. You need to install the RemoteFX 3D Video adapter driver for your virtual machine. What role is required to use this driver? / Should read:
4. You need to install the RemoteFX 3D Video adapter driver for your virtual machine. Which role or role service is required to use this driver?
446 / Chapter 10, Table 10-8, Cmdlet Column, Second Row
Reads:
Get=NetTCPConnection / Should read:
Get-NetTCPConnection
448 / Chapter 10, IPv6 Address Syntax
Replace / Replace with:
IPv6 Address Syntax
Whereas IPv4 addresses use dotted-decimal format as already explained earlier in this chapter, IPv6 addresses are subdivided into eight 16-bit blocks. Each 16-bit block is portrayed as a 4-digit hexadecimal number and is separated from other blocks by colons. This addressing scheme is referred to as colon-hexadecimal.
For example, a 128-bit IPv6 address written in binary could appear as follows:
0011111111111110 1111111111111111 0010000111000101 0000000000000000 0000001010101010 0000000011111111 1111111000100001 0011101000111110
The same address written in colon-hexadecimal becomes 3ffe:ffff:21c5:0000:02aa:00ff:fe21:3a3e. You can remove any single set of contiguous leading zeros, converting this address to 3ffe:ffff:21c5::2aa:ff:fe21:3a3e. This process is known as Zero compression. In this notation, note that the block that contained all zeros appears as “::”, which is called double-colon. You can always figure out how many blocks of zeros are contained within a double-colon because all IPv6 addresses consist of eight 16-bit blocks.
492 / Chapter 11, First Four Paragraphs and First Three Commands under Using Windows PowerShell to Install DHCP
Reads:
You can use PowerShell to install a server role or feature such as DHCP on a server running the Server Core version of Windows Server 2012 R2. To install DHCP, use the following PowerShell cmdlet:
Install-WindowsFeature DHCPServerCore
As was the case with Windows Server 2008 R2, you can also use the Deployment Image Servicing and Management (DISM.exe) tool in Windows Server 2012 R2 to install and configure server roles such as DHCP. Use the following command to install DHCP on a Server Core machine:
Dism /online /enable-feature /featurename:DHCPServerCore
Note that this command is case-sensitive and DHCPServerCore must be typed exactly as indicated.
On a computer running any of the GUI-based editions of Windows Server 2012 R2, use the following command:
Dism /online /enable-feature /featurename:DHCPServer / Should read:
You can use PowerShell to install a server role or feature such as DHCP on a Server GUI/Core version of Windows Server 2012 R2. To install DHCP, use the following PowerShell cmdlet:
Install-WindowsFeature DHCP
As was the case with Windows Server 2008 R2, you can also use the Deployment Image Servicing and Management (DISM.exe) tool in Windows Server 2012 R2 to install and configure server roles such as DHCP. Use the following command to install DHCP:
Dism /online /enable-feature /featurename:DHCPServer
503 / Chapter 11, Second Command and Note
Reads:
Set-DhcpServerv4OptionValue -ScopeID 192.168.0.0 -OptionId 3 -Value 3 IPADDRESS 192.168.0.1
Note For more information on the Set-DhcpServerv4OptionValue cmdlet, refer to " Set-DhcpServerv4OptionValue" at http://technet.microsoft.com/en-us/library/jj590669.aspx. / Should read:
Set-DhcpServerv4OptionValue -ScopeID 192.168.0.0 -OptionId 3 192.168.0.1
Note For this cmdlet to work properly, the scope must first be created before it can be configured. For more information on the Set-DhcpServerv4OptionValue cmdlet, refer to "Set-DhcpServerv4OptionValue" at http://technet.microsoft.com/en-us/library/jj590669.aspx.
508 / Chapter 11, Configuring DHCP Options for PXE, First Paragraph
Reads:
After you have configured WDS with appropriate images, you will need to ensure that your DHCP server is configured with options 066 and 067. These options enable clients to connect to the WDS server using PXE. To configure the options, perform the following steps: / Should read:
After you have configured WDS with appropriate images, you will need to ensure that your DHCP server is configured with options 066 and 067. These options allows clients to connect to the WDS server using PXE. For the purpose of the 70-410 exam, to deploy images using PXE boot, you will need to configure DHCP options 66 and 67. In real world implementations, this may differ depending on the scenario.
For example, if you plan on using Windows Deployment Services on the same server hosting DHCP, you must tell WDS not to listen on UDP port 67 and also to instruct the DHCP server that this server is also a PXE server. This can be accomplished by checking the two options under the DHCP properties of a WDS Server. For Microsoft DHCP servers, WDS will automatically configure Option 060 PXEClient under Scope Options. In scenarios where WDS and DHCP services are installed on separate servers, you must configure DHCP Options 066 and 067. Option 066 identifies the Boot Server Host Name by IP Address. This is the IP Address of the WDS server. Option 067 identifies the Bootfile name. To configure the options, perform the following steps:
513 / Chapter 11, Second Bullet Point, Second to Last Sentence
Reads:
To specify a value for this parameter, right-click the DHCP server in the console tree of the DHCP snap-in. / Should read:
To specify a value for this parameter, right-click the DHCP server in the console tree of the DHCP snap-in and chose Properties.
604 / Chapter 13, Number 1
Reads:
1.  Type Install-windowsfeature –name Ad-Domain-Services –IncludeManagementTools and press Enter. / Should Read:
1.  Type Install-WindowsFeature –name Ad-Domain-Services –IncludeManagementTools and press Enter.
604 / Chapter 13, Number 4, First Sentence
Reads:
4. Windows asks for -safemodeadministratorpassword. / Should read:
4. Windows asks for –SafeModeAdministratorPassword.
605 / Chapter 13, Last Sentence in Paragraph before Note
Reads:
You can also use any of the parameters previously included with the –InstallADDSForest cmdlet and already described. / Should read:
You can also use any of the parameters previously included with the –Install-ADDSForest cmdlet and already described.
606 / Chapter 13, Last Sentence in Paragraph before Note
Reads:
You can also use most of the parameters previously included with the –InstallADDSForest cmdlet described earlier in this section. / Should read:
You can also use most of the parameters previously included with the –Install-ADDSForest cmdlet described earlier in this section.
613 / Chapter 13, Number 4, Second Sentence
Reads:
These relate to the ability of the installation wizard to run the Adprep /domainprep and Adprep /forestprep operations, and are as follows: / Should read:
These relate to the ability of the installation wizard to run the adprep /domainprep and adprep /forestprep operations, and are as follows:
689 / Chapter 15, First Sentence, 1 and 2
Reads:
To create a local group in Windows Server 2012 R2, proceed as follows:
1. Open Server Manager and then expand the Configuration node in the console tree to reveal the Local Users and Groups folder.
2. Expand this folder, right-click Groups, and choose New Group. / Should read:
To create a local group in Windows Server 2012 R2, proceed as follows:
1. Open Server Manager, click on Tools and choose Computer Management. Once Computer Management opens, expand the Configuration node in the console tree to reveal the Local Users and Groups folder.
2. Expand this folder, right-click Groups, and choose New Group.
694 / Chapter 15, Creating Organizational Units, Second Paragraph, First Sentence
Reads:
You can also use the dsadd PowerShell cmdlet or from the Active Directory Module for Windows PowerShell available under Administrative Tools. / Should read:
You can also use the dsadd utility or from the Active Directory Module for Windows PowerShell available under Administrative Tools.
722 / Chapter 16, Delete TIP / No Replacement TIP
734 / Chapter 16, Add TIP Under First TIP / TIP to add:
TIP Beginning with PowerShell 3, moduels may be imported automatically if they are located in a specific configurable path. For more information refer to "Importing Modules" at https://msdn.microsoft.com/en-us/library/dd878284(v=vs.85).aspx.