Site Acceptance Test
Bay of Campeche VTS
Revision:004
Author:Jens Jørgen Jensen
Date:03-09-02
Approved:
Commercial - in - Confidence
File: mex_sat_004Page 1 of 4003-09-2002/AC
Bay of Campeche VTS
Site Acceptance
Test Approval
Test LocationDate
Participants
SAT approved / YES NO
Signatures
1.Revision history
Rev. Level / Date & time / Amended by / Details001 / 17-7-1997 / PBA / TME / Initial version
002 / 17-05-2002 / JJJ / Update of System
003 / 28-05-2002 / JJJ / Tests added in chapter 10
General small changes in the way the tests are done.
004 / 03-07-2002 / JJJ / Correction in System overview 6.2
To 3x64 kbit .
2.Contents
1.Revision history......
2.Contents......
3.Introduction......
3.1Document overview......
3.2Test scenario......
4.Terms and abbreviations used in this document......
5.Reference documents......
6.Test instructions......
6.1Requirements......
6.2System overview for SAT......
7.System test......
7.1Power on test......
7.2DCU display control......
7.3DCU speaker/microphone control......
7.4VHF radio channel selection......
7.4.1VHF radio channel selection fast speed buttons......
7.4.2VHF Scanning......
7.5VHF radio squelch indication......
7.6Voice logging......
7.7Test of Intersite link. Se chapter 12 Comments
7.7.1VHF remote selection of channel (timeout)......
7.7.2VHF remote selection of channel (automatic)......
7.7.3VHF remote selection of channel (manual)......
7.7.4VHF remote selection of channel (audio)......
7.7.5Link disconnected in idle.......
7.7.6Link disconnected during active sessions on remote......
Link disconnected during PTT on remote......
8.System alarms......
8.1Type A alarm......
8.2Type B alarm......
8.3Type C alarm......
9.Leased lines......
9.1Introduction......
9.2Measurements......
9.3Comments for 4-wire leased lines......
10.DCB4140 test procedure......
10.1Tests made during Factory Acceptance Test......
10.1.1Transmitter......
10.1.2Receiver test......
10.2Base transceiver tests during SAT......
10.2.1Test frequencies......
10.2.2Receiver sensitivity......
10.2.3Transmitter output......
10.2.4Dos Bocas......
10.2.5Ixtoc-A......
10.2.6Rebombeo......
10.2.7Eco-1......
10.2.8Cayo Aracas......
10.2.9Laguna Azul......
11.Punch list......
12.Comments......
13.Spanish text in DCU display......
3.Introduction
This document describes the procedure for the Site Acceptance Test (SAT) used with the Danphone Radio Communication System for Bay of Campeche VTS, Mexico.
3.1Document overview
The SAT will cover the following major test issues:
- System functionality
- System alarms
- Measurements on leased lines connections
- Base transceiver measurements
Any punches to the SAT are listed in chapter 11.
Any comments relevant to the SAT are listed in chapter 12.
3.2Test scenario
The system consists of two main sites and 6 remote VHF base transceiver sites. In a number of the tests in the SAT it is essential that the persons involved are situated on different locations, in order to control and observe the system behaviour.
The tests in question are those concerning the intersite link (Se chapter 12 Comments) and the measurements on the 4-wire leased lines. For those tests, one representative from Danphone and one from the on-site commissioning team must be present on each of the locations involved.
Because of the physical distances between the system sites, the tests in the SAT may be carried out separately.
A copy of this SAT document must be present and filled out on each of the two main sites.
Note: It is not possible for the operators on Cayo Arcas main site to access base transceivers connected to Laguna Azul (see Figure 1).
4.Terms and abbreviations used in this document
The system consists of two control centres (Laguna Azul and Cayo Arcas) and a number of remote bases. See Figure 1.
Term / DefinitionLA / Test action is performed at Laguna Azul System only
CA / Test action is performed at Cayo Arcas System only
LA/CA / Test action is performed at both LA and CA.
TBD / To be defined.
5.Reference documents
Document reference no. / Reference title1 / Bay of Campeche, Mexico VTS. System Design Manual, rev. 006.
2 / Factory Acceptance Test, Bay of Campeche VTS, rev. 005.
3
6.Test instructions
6.1Requirements
- VHF handportable radio.
- Stabilock 4040
6.2System overview for SAT
The system to be delivered is depicted in Figure 1.
Figure 1 The entire system
7.System test
7.1Power on test.
No/Pass / System / Action / Result / OKTest 1. / LA/CA / Power off system / No LEDs on any module are lit
Test 2. / Power on system
Run K.BAT on PC. (only for controlling the system under the SAT in real this is done automatically from autoexe.bat) / Software is read from hard disk. System is initialised.
Test 3. / Observe LTC and PCM racks / All units in system are running
Test 4. / Observe DCU display / DCU displays are initialised.
Note: The tests in sections 7.2 and 7.3 are performed for one DCU only.
7.2DCU display control
No/Pass / System / Action / Result / OKTest 5. / LA / Press (Display control key) / Display responds:
CONTRASTE/ PANTALLA
1=PANTALLA//TECL. LUM.
Test 6. / Use the arrow keys (up/down) to adjust display contrast / Display contrast is adjusted
Test 7. / Press '1' / Display responds:
PANTALLA/TECL. LUM.
Test 8. / Use the arrow keys to adjust the display backlight / Display light is adjusted
Test 9. / Press Enter / Exit from Display control mode, display control text disappears
7.3DCU speaker/microphone control
VHF transceiver #1 is used (Ixtoc-A).
No/Pass / System / Action / ResultTest 10. / LA / Select RX on VHF#1.
Enter channel 12 and press Enter. / RX key for the chosen base is lit.
Channel no. for the base is shown in DCU display.
Test 11. / Key portable VHF radio on that channel, and speak / Voice from VHF radio is heard in DCU monitor speaker.
Test 12. / Press 'Monitor Volume' / Display responds:
VOL. BOC. MONITOREO
Test 13. / Use the arrow keys to adjust the monitor speaker volume / Monitor speaker volume is adjusted
Test 14. / Press Enter / Exit from Monitor volume control mode.
Monitor volume control text disappears.
Test 15. / LA / Select TX on VHF#1 Laguna Azul / TX key for the chosen base is flashing.
Channel for chosen base flashes in display.
Test 16. / Key portable VHF radio and speak or use normal traffic on transceiver / Voice from VHF radio is heard in DCU traffic speaker.
Test 17. / Press 'Traffic Volume' / Display responds:
VOL. BOC. TRAFICO
0=DESACTIVAR BOCINA
1=AURICULAR 2=TELEF.
Test 18. / Use the arrow keys to adjust the traffic speaker volume / Traffic speaker volume is adjusted
Test 19. / Press ‘0’ / Traffic speaker is disabled
Display responds:
VOL. BOC. TRAFICO
0=ACTIVAR BOCINA
1=AURICULAR 2=TELEF.
Test 20. / Key portable VHF radio and speak or use normal traffic on transceiver / No voice is heard from the speakers. Voice is heard in headset.
Test 21. / Press ‘0’ / Traffic speaker is enabled
Test 22. / Key portable VHF radio and speak or use normal traffic on transceiver / Voice is heard from the speakers.
Voice is heard in headset.
Test 23. / Key VHF#1 using DCU’s PTT button, and speak in headset microphone / Voice is heard in portable VHF radio or from another site using the same channel.
Test 24. / Press '1' / Display responds:
VOL AURICULAR
(Bar graph)
Test 25. / Use the arrow keys to adjust the headset speaker volume. / Headset volume is adjusted.
The bar graph shows the setting.
Test 26. / Press Enter / Exit from Headset volume control mode
Test 27. / Press “Traffic Volume” / Display responds:
VOL. BOC. TRAFICO
0=DESACTIVAR BOCINA
1=AURICULAR 2=TELEF.
Test 28. / Press “2” / Display responds:
VOL TELEFONO
(Bar graph
Test 29. / Press “Enter” / Exit from Handset volume control mode
Test 30. / PressTX for VHF#1 / Tx key is turned off.
Channel number stops flashing in display.
Test 31. / Key portable VHF and speak or use normal traffic on transceiver / Voice is heard in monitor speaker, not in traffic speaker.
Test 32. / Press RX for VHF#1 / RX key is turned off.
Channel number disappears from display.
7.4VHF radio channel selection
Two DCUs are used at LA.
No/Pass / System / Action / ResultTest 33. / LA/ DCU1 / Press the VHF#1 RX-key / Display responds: VHF00
First digit is flashing
Test 34. / Wait approx 15 sec. (timeout) / Channel number disappears from display
Test 35. / Press the VHF#1 RX-key / Display responds: VHF00
First digit is flashing
Test 36. / Select channel 35 using multi-keys and press ‘Enter’ / Channel number disappears from display.
Error message in display:
CANAL NO VALIDO
Test 37. / Press ‘Enter’ / Error message disappears
Test 38. / Press the VHF#1 RX-key / Display responds: VHF00
First digit is flashing
Test 39. / Select channel 35
Don’t press ‘Enter’ / Display responds:
VHF35(last digit is flashing)
Test 40. / Press the VHF#1 RX-key / Display responds: VHF
i.e. ready for another chan. selection
Test 41. / Select channel 12 on DCU#1 for VHF#1, using multi-keys, press ‘Enter’ / The Channel number is shown in display.
The RX key is lit.
Test 42. / Key a portable VHF radio on channel 12, and speak or use normal traffic on transceiver / The voice is heard in the monitor speaker.
Test 43. / LA / DCU 1 / Select TX on for channel 12 on the DCU (DCU#1) / Channel number flashes in display. TX key is lit.
Test 44. / LA / DCU 2 / Select the VHF base on another DCU (DCU#2), only RX.
Press “Enter” / Display responds: VHF12
First digit is flashing.
Channel 12 is selected automatically if “Enter” is selected, or waiting 15 seconds.
Test 45. / LA / DCU 1 / Press PTT on DCU#1, and speak. / The voice is heard in the monitor speaker of DCU#2, and in the portable radio.
Test 46. / Deselect all bases for all DCUs. / All keys are turned off.
All Channel numbers disappear from DCU displays.
Test 47. / LA / Press the VHF#1 RX-key on DCU#1 / Display responds: VHF00
First digit is flashing
Test 48. / Press the VHF#1 RX-key on DCU#2 / Error message:
ACCESO DENEGADO
Test 49. / Press ‘Enter’ on DCU#2 / Error message disapears.
Test 50. / Select channel 12 on DCU#1 for VHF#1, press ‘Enter’ / The Channel number is shown in display.
The RX key is lit.
Test 51. / Press the VHF#2 RX-key on DCU#1 / Display responds: VHF00
First digit is flashing
Test 52. / Select channel 12 on DCU#1 for VHF#2, press ‘Enter’ / The Channel number is shown in display.
The RX key is lit.
Test 53. / Key a portable VHF radio on channel 12 and speak or use normal communication on channel / The voice is heard in the monitor speaker
Test 54. / Deselect all bases for all DCUs. / All keys are turned off.
All base names disappear from DCU displays.
Test 55. / LA / Press the VHF # 1 TX-Key on DCU#1 / Display responds: VHF00
First digit is flashing
Test 56. / Select channel 12 from multi-keys and press “Enter” / RX-key for chosen base is on.
TX-key for the chosen base is flashing.
Channel number of chosen base flashes in display
Test 57. / Key a portable VHF radio on channel 12 and speak / The voice is heard in the traffic speaker
Test 58. / Press the VHF # 1 RX-key on DCU # 1 / RX / TX keys are turned off.
Channel number disappear from DCU
7.4.1VHF radio channel selection fast speed buttons
Test 59. / Press the VHF # 1 TX-Key on DCU#1 / Display responds: VHF00First digit is flashing
Test 60. / Select channel 11 from Fast speed buttons / RX-key for chosen base is on.
TX-key for the chosen base is flashing.
Channel number of chosen base flashes in display
Test 61. / Press the VHF # 1 RX-key on DCU # 2 / Display responds: VHF11
First digit is flashing
Test 62. / Select channel 12 from Fast speed buttons / Displays on DCU # 1 and DCU # 2 change to channel 12 TX is removed from DCU # 1 display.
Test 63. / Key a portable VHF radio on channel 12 and speak or use normal traffic on channel / The voice is heard in the monitor speaker on DCU # 1 and in monitor speaker on DCU # 2
Test 64. / Press VHF#1 RX-key on both DCU / RX / TX keys are turned off.
Channel number disappear from DCUs
7.4.2VHF Scanning
Test 65. / Press the SCAN and then VHF#1 RX-key on DCU#2 / Display responds: VHF00First digit is flashing
Test 66. / Press from the Fast Speed buttons Channel no: 6–8-10-11-12 and finaly press “Enter” / Display responds: VHF99
RX-key for chosen base is on.
Test 67. / Key a portable VHF radio on channel 11 and speak or use normal traffic on one of the selected channels / Display responds: VHF11 * or first channel with traffic on
Voice is heard in monitor speaker
Test 68. / Dekey the portable VHF and wait 15 seconds or until no communication / Display responds: VHF99
And scanning continue
Test 69. / Key a portable VHF radio on channel 08 and speak or use normal traffic on channels / Display responds: VHF08 * or next channel with traffic on
Voice is heard in monitor speaker
Test 70. / Dekey the portable VHF and wait 15 seconds or until no communication / Display responds: VHF99
and scanning continue
Test 71. / DCU 2 / Press VHF#1 RX-key on DCU#2 / RX / TX keys are turned off.
Channel number disappear from DCUs
Test 72. / DCU 2 / Press the SCAN and then VHF#1 RX-key on DCU#2 / Display responds: VHF00
First digit is flashing
Test 73. / Press from the Fast Speed buttons Channel no: 6–8-10-11-12 and finish with Enter / Display responds: VHF99
RX-key for chosen base is on.
Test 74. / DCU 1 / Press RX-key on DCU#1 / Display responds: VHF99
First digit flashing
Test 75. / Press “Enter” on DCU#1 / Display responds: VHF99
Test 76. / Key a portable VHF radio on channel 11 and speak or use normal traffic on channels / Display responds: VHF11 * on both DCUs or first channel with traffic on
And voice is heard in monitor speaker on both DCUs
Test 77. / Dekey portable and wait 15 seconds or wait until no communication / Display responds: VHF99 on both DCUs
Test 78. / Key a portable VHF radio on channel 12 and speak or use normal traffic on channel / Display responds: VHF12 * on both DCUs or next channel with traffic on
And voice is heard in monitor speaker on both DCUs
Test 79. / Press TX-Key on VHF#1 on DCU#2 / Display responds: VHF12
Light in TX button flashes and display flashes
Test 80. / Dekey portable and wait 15 seconds / Display responds: VHF12
Light in TX button flashes and display flashes.
Base will stay on channel 12 on both DCUs
Test 81. / Press TX-Key on VHF#1 on DCU#2 / Display responds: VHF99 on both DCUs and scanning will continue.
Test 82. / Press VHF#2 RX-key on both DCUs / RX / TX keys are turned off.
Channel number disappear from DCUs
7.5VHF radio squelch indication
No/Pass / System / Action / ResultTest 83. / LA / Press the VHF#1 RX-key / Display responds: VHF00
First digit is flashing
Test 84. / Select channel 12 on DCU#1 for VHF#1, press ‘Enter’ / The channel number is shown in display.
The RX key is lit.
Test 85. / Key a portable VHF radio on channel 12, and speak, or use normal traffic on channel / The voice is heard in the monitor speaker.
Observe that the squelch indication (an asterisk) is shown next to the channel number in the DCU display.
Test 86. / Dekey portable VHF radio or wait until no communication / Observe that the squelch indication changes to a + and disappears after 7 seconds.
Test 87. / Deselect all bases for all DCUs. / All keys are turned off.
All channel numbers disappear from DCU displays.
7.6Voice logging
Connect a Stabilock to the output from the voice logger, in order to monitor voice output from the voice logger equipment (VLO769).
The system must be in idle state, i.e. no bases are selected.
The voice logging is unit associated, i.e. voice logging for RIM705 unit #1 is always on VLO769 channel #1. These are used in the following to test the voice logging.
No/Pass / System / Action / ResultTest 88. / LA / Select channel 12 for monitoring. / VHF12 is shown in DCU display.
Test 89. / Key portable VHF radio on channel 12. / Audio from VHF radio is heard in DCU monitor speaker and in stabilock.
Test 90. / Select channel 12 for traffic / VHF12 is flashing in DCU display.
Test 91. / Key VHF base and speak in headset microphone / Audio from DCU is heard in stabilock.
Test 92. / Deselect all bases for all DCUs. / All keys are turned off.
All channel numbers disappear from DCU display.
This test can be repeated on any base.
7.7Test ofIntersite link. Se chapter 12 Comments
“System” describes the location of the action.
7.7.1VHF remote selection of channel (timeout)
No/Pass / System / Action / ResultTest 93. / LA / Select RX on CA VHF / At LA: DCU display start: VHF00
Test 94. / CA / Select RX on LA VHF#1 / At CA: Error message “ACCESO DENEGADO”.
Test 95. / LA / Wait 30 sec. / At LA: DCU display is cleared for channel input
7.7.2VHF remote selection of channel (automatic)
No/Pass / System / Action / ResultTest 96. / CA / Enter channel 68 at CA VHF / At CA: Channel number VHF68 + key light RX
Test 97. / LA / Select RX on CA VHF from LA DCU / At LA: channel 68 is selected automatically: VHF68 in DCU display.
Test 98. / LA / Select RX off CA VHF / At LA: Channel number and key lights off.
Test 99. / CA / Select RX off CA VHF / At CA: Channel number and key lights off.
7.7.3VHF remote selection of channel (manual)
No/Pass / System / Action / ResultTest 100. / LA / Select RX on CA VHF / At LA: DCU display start: VHF00
Test 101. / LA / Enter VHF channel 12 / At LA: Channel number VHF12 + key light RX
Test 102. / CA / Select RX on CA VHF / At CA: channel 12 is selected automatically: VHF12 in DCU display.
7.7.4VHF remote selection of channel (audio)
No/Pass / System / Action / ResultTest 103. / CA / Key portable VHF radio on channel 12, and speak or use normal traffic on channel / At LA: Voice is heard in DCU monitor speaker.
At CA: Voice is heard in DCU monitor speaker.
Test 104. / LA / Select TX on CA VHF#1 / At LA: Channel number flashes. Tx key light is turned on.
Test 105. / LA / Key CA VHF from DCU, and speak in headset microphone / At CA: Voice is heard on portable VHF.
Test 106. / LA / Dekey
Test 107. / LA / Deselect all bases for all DCUs. / All keys are turned off.
All Channel numbers disappear from DCU display.
Test 108. / CA / Deselect all bases for all DCUs. / All keys are turned off.
All Channel numbers disappear from DCU display.
7.7.5Link disconnected in idle.
No/Pass / System / Action / ResultTest 109. / CA / Disconnect Link. / At CA/LA: DCUs display
ERROR ENLACE CYA-LA
Test 110. / CA / Connect Link. View alarm log using DCU arrow buttons. / At CA/LA: DCUs display
ERROR ENLACE CYA-LA* is removed (change indicated by asterisk)
7.7.6Link disconnected during active sessions on remote
No/Pass / System / Action / ResultTest 111. / LA / Select RX on CA VHF, channel 12. / At LA: Channel number and key light on at DCU.
Test 112. / CA / Key portable VHF radio on channel 12 to check the connection. / At LA: voice is heard in DCU monitor speaker.
Test 113. / LA / Select TX on CA VHF. / At LA: Channel number flashes, TX key light is turned on.
Test 114. / CA / Disconnect link / At CA/LA: DCUs display
ERROR ENLACE CYA-LA.
At LA: DCU Message displays
FALA COM. CAYO ARACAS.
At LA: base name disappears from DCU display. RX and TX keys are turned off.
Test 115. / LA / Connect link. / The ERROR ENLACE CYA-LA* is prefixed with a *.
Test 116. / LA / Select RX on CA VHF, channel 12. / At LA: Channel number and key light on at DCU.
Test 117. / CA / Key portable VHF radio on channel 12 to check the connection. / At LA: voice is heard in DCU monitor speaker.
Test 118. / LA / Select TX on CA VHF. Key the base and speak in the headset microphone. / At LA: Channel number flashes, TX key light is turned on.
At CA: voice is heard in portable VHF radio.
Test 119. / LA / Dekey CA VHF, and select TX and RX off. / At LA: Channel number disappears in DCU display. RX and TX keys are turned off.
Link disconnected during PTT on remote
No/Pass / System / Action / ResultTest 120. / LA / Select RX on CA VHF, channel 12. / At LA: Channel number and key light on at DCU.
Test 121. / CA / Key portable VHF radio on channel 12 to check the connection. / At LA: voice is heard in DCU monitor speaker.
Test 122. / LA / Select TX on CA VHF. / At LA: Channel number flashes, TX key light is turned on.
Test 123. / LA / Key the base and speak in the headset microphone. / At LA: Channel number flashes, TX key light is turned on.
At CA: voice is heard in portable VHF radio.
Test 124. / LA / Disconnect link / At CA/LA: DCUs display
ERROR ENLACE CYA-LA
At LA: DCU Message displays
FALA COM. CAYO ARACAS.
At LA: Channel number disappears from DCU display. RX and TX keys are turned off.
Test 125. / LA / Connect link. / ERROR ENLACE CYA-LA *This is prefixed with a *.
Test 126. / LA / Select RX on CA VHF, channel 12. / At LA: Channel number and key light on at DCU.
Test 127. / CA / Key portable VHF radio on channel 12 to check the connection or use normal communication / At LA: voice is heard in DCU monitor speaker.
Test 128. / CA / Select TX on CA VHF. / At LA: Channel number flashes, TX key light is turned on.
Test 129. / LA / Key the base and speak in the headset microphone. / At LA: Channel number flashes, TX key light is turned on.
At CA: voice is heard in portable VHF radio.
Test 130. / LA / Dekey CA VHF, and select TX and RX off. / At LA Channel number disappears in DCU display. RX and TX keys are turned off.
8.System alarms