Exit Hardware

SECTION 08 71 00

EXIT HARDWARE

** NOTE TO SPECIFIER ** Von Duprin an Allegion Brand; Exit Hardware.
This section is based on the products of Von Duprin an Allegion Brand, which is located at:
11819 N. Pennsylvania St.
Carmel, IN 46032
Toll Free Tel: 877-578-1247
Email: request info ()
Web: us.allegion.com/brands/von_duprin/Pages/default.aspx
[ Click Here ] for additional information.
Von Duprin manufactures the widest range of exit devices and outside trim operations as well as a full line of electromagnetic locks, electric strikes, card readers, and keypad-type access control systems

1 GENERAL

1.1   SECTION INCLUDES

1.1.1   Exit Device Hardware.

1.2   RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

1.2.1   Section 05 10 00 - Structural Metal Framing.

1.2.2   Section 06 10 00 - Rough Carpentry.

1.2.3   Section 08 11 00 - Metal Doors and Frames.

1.2.4   Section 08 10 00 - Doors and Frames.

1.2.5   Section 26 05 00 - Common Work Results for Electrical.

1.3   REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

1.3.1   ANSI A117.1 - Accessible and Useable Buildings and Facilities.

1.3.2   ANSI A156.3 - Door Controls - Exit Devices.

1.3.3   Underwriters Laboratories (UL). - Fire Resistance Directory.

1.4   SUBMITTALS

1.4.1   Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2   Product Data: Manufacturer's data sheets on each product to be used, including:

1.4.2.1   Preparation instructions and recommendations.

1.4.2.2   Storage and handling requirements and recommendations.

1.4.2.3   Installation methods.

1.4.3   Shop Drawings: Manufacturer's approved shop drawings are required detailing the application of each product specified.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

1.4.4   Selection Samples: For each finish product specified, two full size samples representing manufacturer's full range of available colors and patterns.

1.4.5   Verification Samples: For each finish product specified, two full size samples, representing actual product, color, and patterns.

1.5   QUALITY ASSURANCE

1.5.1   Manufacturer Qualifications: All equipment specified in this section will be provided by a single manufacturer with a minimum of ten (10) years experience manufacturing door hardware.

1.5.2   Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

1.5.3   Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

1.5.3.1   Finish areas designated by Architect.

1.5.3.2   Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.

1.5.3.3   Refinish mock-up area as required to produce acceptable work.

1.6   DELIVERY, STORAGE, AND HANDLING

1.6.1   Store products in manufacturer's unopened packaging until ready for installation.

1.6.2   Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.7   PROJECT CONDITIONS

1.7.1   Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.8   WARRANTY

1.8.1   At project closeout, provide to the Owner or Owner's Representative an executed copy if the manufacturer's Limited Warranty against Manufacturing Defects.

** NOTE TO SPECIFIER ** Select warranty duration based on Device specified.

1.8.1.1   Duration: ______(_) years.

1.9   EXTRA MATERIALS

1.9.1   Provide to the Owner two sets of keys for each lock.

2 PRODUCTS

2.1   MANUFACTURERS

2.1.1   Acceptable Manufacturer: Von Duprin an Allegion Brand, which is located at: 11819 N. Pennsylvania St.; Carmel, IN 46032; Toll Free Tel: 877-578-1247; Email: request info (); Web: us.allegion.com/brands/von_duprin/Pages/default.aspx

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

2.1.2   Substitutions: Not permitted.

2.1.3   Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

** NOTE TO SPECIFIER ** Retain the next Article only if Non-Fire Door Exit Devices are required. Retain only models specifically required on this project and modify the included text as instructed.

2.2   EXIT DEVICES

** NOTE TO SPECIFIER ** Retain the next paragraph only if rim devices are specified. Retain the models specified from the included five paragraphs and delete all others.

2.2.1   Rim Devices:

2.2.1.1   98/99 Rim Exit Device:

2.2.1.1.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.1.1.2   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.1.1.3   Dimensions:

2.2.1.1.3.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.1.1.3.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.1.1.3.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.1.2   33A/35A Rim Exit Device:

2.2.1.2.1   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.1.2.2   Dimensions:

2.2.1.2.2.1   Center Case: 8 3/16 inches by 2 13/32 inches by 1 9/16 inches (208mm x 62mm x 40mm).

2.2.1.2.2.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.1.2.2.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.1.3   88 Rim Exit Device:

2.2.1.3.1   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.1.3.2   Dimensions:

2.2.1.3.2.1   Crossbar Length: 42 inches (1067mm), field sizeable.

2.2.1.3.2.2   Crossbar Projection (Maximum): 4 3/4 inches (121mm).

2.2.1.3.2.3   Crossbar Tubing: 1 inch (25mm).

2.2.1.3.2.4   Lock Stile Case: 8 1/4 inches by 2 3/4 inches by 15/16 inches (210mm x 70mm x 24mm).

2.2.1.3.2.5   Hinge Stile Case: 6 inches by 1 3/4 inches by 15/16 inches (152mm x 44mm x 24mm).

2.2.1.4   55 Rim Exit Device:

2.2.1.4.1   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.1.4.2   Dimensions:

2.2.1.4.2.1   Crossbar Length: 42 inches (1067mm), field sizeable.

2.2.1.4.2.2   Crossbar Projection (Maximum): 3 3/4 inches (95mm).

2.2.1.4.2.3   Crossbar Tubing: 1 inch (25mm).

2.2.1.4.2.4   Lock Stile Case: 7 1/4 inches by 1 3/16 inches by 2 1/4 inches (184mm x 30mm x 57mm).

2.2.1.4.2.5   Hinge Stile Case: 7 1/4 inches by 1 3/16 inches by 2 1/4 inches (184mm x 30mm x 57mm).

2.2.1.5   22 Rim Exit Device:

2.2.1.5.1   Function: EO/DT/NL/TP/K/L Field Selectable.

2.2.1.5.2   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.1.5.3   Dimensions:

2.2.1.5.3.1   Center Case: 4 1/4 inches by 1 3/8 inches by 2 3/8 inches (108mm x 41mm x 60mm).

2.2.1.5.3.2   Mechanism Case: 2 inches by 2 3/8 inches (51mm x 60mm).

2.2.1.5.3.3   Projection (Maximum): 3 3/4 inches (95mm).

** NOTE TO SPECIFIER ** Retain the next paragraph only if mortise lock devices are specified. Retain the models specified from the included three paragraphs and delete all others.

2.2.2   Mortise Lock Devices:

2.2.2.1   9875/9975 Mortise Lock Device:

2.2.2.1.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.2.1.2   Dimensions:

2.2.2.1.2.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.2.1.2.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.2.1.2.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.2.2   8875 Mortise Lock Device:

2.2.2.2.1   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.2.2.2   Dimensions:

2.2.2.2.2.1   Crossbar Length: 42 inches (1067mm), field sizeable.

2.2.2.2.2.2   Crossbar Projection (Maximum): 4 7/8 inches (124mm).

2.2.2.2.2.3   Crossbar Tubing: 1 inch (25mm).

2.2.2.2.2.4   Lock Stile Case: 8 1/4 inches by 2 inches by 15/16 inches (210mm x 51mm x 24mm).

2.2.2.2.2.5   Hinge Stile Case: 6 inches by 1 3/4 inches by 15/16 inches (152mm x 44mm x 24mm).

2.2.2.3   5575 Mortise Lock Device:

2.2.2.3.1   Latch Bolt: Deadlocking 3/4 inch (19mm) throw.

2.2.2.3.2   Dimensions:

2.2.2.3.2.1   Crossbar Length: 42 inches (1067mm), field sizeable.

2.2.2.3.2.2   Crossbar Projection (Maximum): 3 3/4 inches (95mm).

2.2.2.3.2.3   Crossbar Tubing: 1 inch (25mm).

2.2.2.3.2.4   Lock Stile Case: 7 1/4 inches by 1 3/16 inches by 2 1/4 inches (184mm x 30mm x 57mm).

2.2.2.3.2.5   Hinge Stile Case: 7 1/4 inches by 1 3/16 inches by 2 1/4 inches (184mm x 30mm x 57mm).

** NOTE TO SPECIFIER ** Retain the next paragraph only if surface mounted vertical rod devices are specified. Retain the models specified from the included four paragraphs and delete all others.

2.2.3   Surface Mounted Vertical Rod Devices:

2.2.3.1   9827/9927 Surface Mounted Vertical Rod Device:

2.2.3.1.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.3.1.2   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.3.1.3   Dimensions:

2.2.3.1.3.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.3.1.3.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.3.1.3.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.3.1.3.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.3.1.3.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

2.2.3.2   3327A/3527A Surface Mounted Vertical Rod Device:

2.2.3.2.1   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.3.2.2   Dimensions:

2.2.3.2.2.1   Center Case: 8 3/16 inches by 2 13/32 inches by 1 9/16 inches (208mm x 62mm x 40mm).

2.2.3.2.2.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.3.2.2.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.3.2.2.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.3.2.2.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

2.2.3.3   8827 Surface Mounted Vertical Rod Device:

2.2.3.3.1   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.3.3.2   Dimensions:

2.2.3.3.2.1   Crossbar Length: 42 inches (1067mm), field sizeable.

2.2.3.3.2.2   Crossbar Projection (Maximum): 4 7/8 inches (124mm).

2.2.3.3.2.3   Crossbar Tubing: 1 inch (25mm).

2.2.3.3.2.4   Lock Stile Case: 8 1/4 inches by 2 inches by 15/16 inches (210mm x 51mm x 24mm).

2.2.3.3.2.5   Hinge Stile Case: 6 inches by 1 3/4 inches by 15/16 inches (152mm x 44mm x 24mm).

2.2.3.3.2.6   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.3.3.2.7   Latch Case: 4 inches by 2 inches by 1 7/8 inches (102mm x 51mm x 48mm).

2.2.3.4   2227 Surface Mounted Vertical Rod Device:

2.2.3.4.1   Function: EO/DT/NL/TP/K/L Field Selectable.

2.2.3.4.2   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.3.4.3   Dimensions:

2.2.3.4.3.1   Center Case: 4 1/4 inches by 1 3/8 inches by 2 3/8 inches (108mm x 41mm x 60mm).

2.2.3.4.3.2   Mechanism Case: 2 inches by 2 3/8 inches (51mm x 60mm).

2.2.3.4.3.3   Projection (Maximum): 3 3/4 inches (95mm).

2.2.3.4.3.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.3.4.3.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

** NOTE TO SPECIFIER ** Retain the next paragraph only if three-point latching devices are specified.

2.2.4   Three-Point Latching Devices:

2.2.4.1   9857/9957 Three-Point Latching Device:

2.2.4.1.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.4.1.2   Latch Bolt: Deadlocking rim bolt, 3/4 inch (19mm) throw and deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.4.1.3   Dimensions:

2.2.4.1.3.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.4.1.3.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.4.1.3.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.4.1.3.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.4.1.3.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

** NOTE TO SPECIFIER ** Retain the next paragraph only if concealed vertical rod devices are specified. Retain the models specified from the included six paragraphs and delete all others.

2.2.5   Concealed Vertical Rod Devices:

2.2.5.1   9847/9947 Concealed Vertical Rod Device:

2.2.5.1.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.5.1.2   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.

2.2.5.1.3   Dimensions:

2.2.5.1.3.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.5.1.3.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.5.1.3.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.5.1.3.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.5.1.3.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

2.2.5.2   9848/9948 Concealed Vertical Rod Device:

2.2.5.2.1   Function: EO/DT/NL Field Selectable. For TP, K, or L, remove NL drive screw.

2.2.5.2.2   Latch Bolt: Deadlocking top bolt, 3/4 inch (19mm) throw and deadlocking bottom bolt, 1 1/2 inch (38mm) throw.

2.2.5.2.3   Dimensions:

2.2.5.2.3.1   Center Case: 8 inches by 2 3/4 inches by 2 3/8 inches (203mm x 70mm x 60mm).

2.2.5.2.3.2   Mechanism Case: 2 1/4 inches by 2 1/4 inches (57mm x 57mm).

2.2.5.2.3.3   Projection (Maximum): 3 13/16 inches (97mm).

2.2.5.2.3.4   Vertical Rods: 1/2 inch (13mm) square tubing.

2.2.5.2.3.5   Latch Case: 4 1/2 inches by 2 1/8 inches by 1 1/2 inches (114mm x 54mm x 38mm).

2.2.5.3   3347A/3547A Concealed Vertical Rod Device:

2.2.5.3.1   Latch Bolt: Deadlocking anti-friction top and bottom bolt, 5/8 inch (16mm) throw.