GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
GATE 2007 Civil Engineering Question Paper
1.
Q.1 - Q.20 Carry One Mark Each.
1 1 3
The minimum and the maximum eigen velue of the matrix 1 5 1 are -2 and 6, respectively. What
3 1 1
is the other eigen value ?
(a)5(b)3(c)1(d)-1
The degree of the differential equation
2.
d2 x
dt 2
2x 3 is
(c)
2
(d)
3
(a)
3.
0
(b)
1
The solution for the differential equation
(A)
y=
1
e 2x
dy2
= x y with the condition that y = 1 at x = 0 is
dx
x
4 (C)
3
3
(B)
ln(y) =
ln(y) =
x
2
2
(D)
y=
x3
e3
4.
5.
An axially loaded bar is subjected to a normal stress of 173 MPa. The shear stress in the bar is
(a)75 MPa(b)86.5 MPa(c)100 MPa(d) 122.3 MPa
A steel column, pinned at both ends, has a buckling load of 200kN. If the column is restrained against
lateral movement at its mid-height, its buckling load will be
(A)200kN(B)283kN(C)400kN(D)800kN
The stiffness coefficient kij indicates
(a)force at i due to a unit deformation at j
(b)deformation at j due to a unit force at i
(c)deformation at i due to a unit force j
(s)force at j due to a unit deformation i
For an isotropic material, the relationship between the Young’s modulus (E), shear modulus (G) and
Poisson’s ratio () is given by
EG
(A)G=(B)E
2(1 )2(1 )
EE
(D)G=(C)G=
(1 2)2(1 )
A clay soil sample is tested in a triaxial apparatus in consolidated-drained conditions at a cell pressure
22
of 100 kN/m . What will be the pore water pressure at a deviator stress of 40 kN/m ?
2222
(a)0 kN/m(b)20 kN/m(c)40 kN/m(d)60 kN/m
The number of blows observed in a Standard Penetration Test (SPT) for different penetration depths
are given as follows
Penetration of sampler Number of blows
0-150 mm6
150-3008
300-450 mm10
The observed N value is
(a)8(b)14(c)18(d)24
6.
7.
8.
9.
Page 1 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
10.
The vertical stress at some depth below the corner of a 2m x 3m rectangular footing due to a certain
22
load intensity is 100 kN/m . What will be the vertical stress in kN/m below the centre of a 4m x 6m
rectangular footing at the same depth and same load intensity?
(a)25(b)100(c)200(d)400
There is a free overfall at the end of a long open channel. For a given flow rate, the critical depth is
less than the normal depth. What gradually varied flow profile will occur in the channel for this flow
rate ?
(b)M2(c)M3(d)S1(a)M1
The consumptive use of water for a crop during a particular stage of growth is 2.0 mm/day. The
maximum depth of available water in the root zone is 60 mm. Irrigation is required when the amount
of available water in the root zone. Frequency of irrigation should be
(a)10 days(b)15 days(c)20 days(d)25 days
As per the Lacey’s method for design of a alluvail channels, identify the true statement from the
following
(a)Wetted perimeter increases with an increase in design discharge
(b)Hydraulic radius increases with an increase in silt factor.
(c)Wetted perimeter decreases with an increase in design discharge.
(d)Wetted perimeter increases with an increase in silt factor
At two points 1 and 2 in a pipeline the velocities and V and 2V, respectively. Both the points are at
the same elevation. The fluid density is . The flow can be assumed to be in compressible, inviscid,
steady and irrotational. The difference in pressures P1 and P2 at points at 1 and 2 is
2222
(a)0.5 V(b)1.5 V(c)2V(d)3 V
The presence of hardness in excess of permissible limit causes
(a)cardio vascular problems
(b)skin discolouration
(c)calcium deficiency
(d)increased laundry expenses
The dispersion of pollutants in atmosphere is maximum when
(a)environmental lapse rate is greater than adiabatic lapse rate
(b)environmental lapse rate is less than adiabatic lapse rate
(c)environmental lapse rate is equal to adiabatic lapse rate
(d)maximum mixing depth is equal to zero
The alkalinity and hardness of a water sample are 250 mg/L and 350 mg/L as CaCO3, respectively.
The water has
(a)350 mg/L carbonate hardness and zero non-carbonate hardness.
(b)250 mg/L carbonate hardness and zero non-carbonate hardness.
(c)250 mg/L carbonate hardness and 350 mg/L non-carbonate hardness.
(d)250 mg/L carbonate hardness and 100 mg/L non-carbonate hardness.
The consistency and flow resistance of bitumen can be determined from the following
(a)Ductitility test
(b)Penetration test
(c)Softening point test
(d)Viscosity test
11.
12.
13.
14.
15.
16.
17.
18.
Page 2 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
19.
If a two-lane national highway and a two-lane state highway intersect at right angles, the number of
potential conflict points at the intersecton, assuming that both the roads are two-way is
(a)11(b)17(c)24(d)32
In signal design as per Indian Roads Congress specifications, if the sum of the ratios of normal flows
to saturation flow of two directional traffic flow is 0.50 and the total lost time per cycle is 10 seconds,
the optimum cycle length in seconds is
(a)100(b)80(c)60(d)40
Q. 21 to Q.75 carry two marks each :
For what values of α and the following simultaneous equations have an infinite number of
solutions?
x+y+z = 5; x+3y+3z = 9;
x+2y+az =
(a)2,7(b)3,8(c)8,3(d)7,2
20.
21.
22.
A velocity vector is given as
V 5 xy i 2 y 2 j 3yz 2 k
The divergence of this velocity vector a (1,1,1) is
(a)9(b)10(c)
14
(d)
15
23.
A body originally at 60C cools down to 40C in 15 minutes when kept in air at a temperature of 25C.
What will be the temperature of the body at the end of 30 minutes ?
(b)31.5C(c)28.7C(d)15C(a)35.2C
The following equation needs to be numerically solved using the Newton-Raphson method.
3
x +4x-9 = 0
The iterative equation for this purpose is (k indicates the iteration level)
322x k 92x k 4
x k 1 x k 1 (B)(A)
223x k 43x k 4
(C)
x k 1
2x k 3x k
24.
4
(D)
x k 1
24x k 3
29x k 2
25.
Evaluate
(a)
0
sin t
dt
t
(b)
/2
2
2
(c)
/4
(d)
/3
26.
Potential function is given as = x + y . What will be the stream function (ψ) with the condition ψ
= 0 at x = y = 0 ?
22222 2
(a)2xy(b)x +y(c)x y(d)2x y
1
The inverse of the 2 2 matrix
5
7 2 7
(A)(B)
5 15
2
is
7
2
1
3
2
27.
(C)
1 7 2
3 5 1
(D)
1 7 2
3 5 1
28.
Given that one root of the equation x 10x + 31x 30 = 0 is 5, the other two roots are
(a)2 and 3(b)2 and 4(c)3 and 4(d)2 and 3
Page 3 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
29.
If the standard deviation of the spot speed of vehicles in a highway is 8.8 kmph and the mean speed
of the vehicles is 33 kmph, the coefficient of variation in speed is
(a)
30.
0.1517
(b)
0.1867
(c)
0.2666
(d)
0.3646
A metal bar of length 100 mm is inserted between two rigid supports and its temperature is increased
-6
by 10C. If the coefficient of thermal expansion is 12 10 per C and the young’s modulus is 2 ×
5
10 MPa, the stress in the bar is
(a)
zero
(b)
12 MPa
(c)
24 MPa
(d)
2400 MPa
31.
A rigid bar is suspended by three rods made of the same material as shown in the figure. The area
and length of the central rod are 3A and L, respectively while that of the two outer rods are 2A and
2L, respectively. If a downward force of 50 kN is applied to the rigid bar, the forces in the central and
each of the outer rods will be
(a)
(c)
16.67 kN each
30 kN and 10 kN
(b)
(d)
30 kN and 15 kN
21.4 kN and 14.3 kN
32.
The maximum and minimum shear stresses in a hollow circular shaft of outer diameter 20 mm and
thickness 2mm, subjected to a torque of 92.7 N.m will be
(a)
(c)
59 MPa and 47.2 MPa
118 MPa and 160 MPa
(b)
(d)
100 MPa and 80 MPa
200 MPa and 160 MPa
33.
The shear stress at the neutral axis in a beam of triangular section with a base of 40 mm and height
20 mm, subjected to a shear force of 3 kN is
(a)
3 MPa
(b)
6 MPa
(c)
10 MPa
(d)
20 MPa
34.
U1 and U2 are the strain energies stored in a prismatic bar due to axial tensile forces P1 and P2,
respectively. The strain energy U stored in the same bar due to combined action of P1 and P2 will be.
(a)
U = U1 + U 2
(b)
U = U1U2
(c)
U < U1 + U 2
(d)
U > V1 + U2
2
35.
The right triangular truss is made of members having equal cross sectional area of 1550 mm and
5
Young’s modulus of 2 10 MPa. The horizontal deflection of the joint Q is
(a)
2.47 mm
(b)
10.25 mm
(c)
14.31 mm
(d)
15.68 mm
Page 4 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
36.
The influence line diagram (ILD) shown is for the member
(a)
37.
PS
(b)
RS
(c)
PQ
(d)
QS
Consider the following statements :
I.
II.
III.
The compressive strength of concrete decreases with increase in water-cement ratio of the
concrete mix.
Water is added to the concrete mix for hydration of cement and workability.
Creep and shrinkage of concrete are independent of the water-cement ratio in the concrete
mix.
I and II
(b)
I, II and III
(c)
II and III
(d)
only II
The true statements are
(a)
38.
The percentage loss of prestress due to anchorage slip of 3 mm in a concrete beam of length 30 m
2
which is post-tensioned by a tendon with an initial stress of 1200 N/mm and modulus of elasticity
52
equal to 2.1 x 10 N/mm is
(a)
0.0175
(b)
0.175
(c)
1.75
(d)
17.5
39.
A concrete beam of rectangular cross-section of size 120 mm (width) and 200 mm (depth) is
prestressed by a straight tendon to an effective force of 150 kN at an eccentricity of 20 mm (below
the centroidal axis in the depth direction). The stresses at the top and bottom fibres of the section
are
(a)
(b)
(c)
(d)
2.5 N/mm (compression), 10N/mm (compression), 10N/mm (compression).
10N/mm (tension), 2.5 N/mm (compression)
3.75 N/mm (tension), 3.75 N/mm (compression)
2.75 N/mm (compression), 3.75 N/mm (compression)
2
2
2
2
2
2
2
2
2
40.
Consider the following statements :
I.
II.
III.
(a)
Modulus of elasticity of concrete increases with increase in compressive strength of concrete.
Brittleness of concrete increases with decrease in compressive strength of concrete.
Shear strength of concrete increases with increase in compressive strength of concrete.
II and III
(b)
I, II and III
(c)
I and II
(d) I and III
The TRUE statements are
Page 5 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
41.
A steel flat of rectangular section of size 70 6 mm is connected to a gusset plate by three bolts each
having a shear capacity of 15 kN in holes having diameter 11.5 mm. If the allowable tensile stress in
the flat is 150 MPa, the maximum tension that can be applied to the flat is
(a)
(b)
(c)
(d)
42.
42.3 kN
52.65 kN
59.5 kN
63.0 kN
A bracket connection is made with four bolts of 10 mm diameter and supports a load of 10 kN at an
eccentricity of 100 m. The maximum force to be resisted by any bolt will be
P
10kN
30
30
40 40
(a)
43.
5 kN
(b)
6.5 kN
(c)
6.8 kN
(d)
7.16 kN
The plastic collapse load Wp for the
propped cantilever supporting two
point loads as shown in figure terms
of plastic moment capacity, Mp is
given by
(a)
(c)
3 Mp/L
4MP/L
(b)
(d)
4MP/L
6MP/L
44.
Sieve analysis on a dry soil sample of mass 1000 g showed that 980 g and 270 g of soil pass through
4.75 mm and 0.075 mm sieve, respectively. The liquid limit and plastic limits of the soil fraction
passing through 425sieves are 40% and 18% respectively. The soil may be classified as
(a)
SC
(b)
MI
(c)
CI
(d) SM
45.
The water content of a saturated soil and the specific gravity of soil solids were found to be 30% and
2.70, respectively. Assuming the unit weight of water to be 10 kN/m3, the saturated unit weight
3
(kN/m ) and the void ratio of the soil are
(a)
19.4, 0.81
(b)
18.5, 0.30
(c)
19.4, 0.45
(d)
18.5, 0.45
Page 6 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
46.
The factor of safety of an infinite soil slope shown in the figure having the properties
033c = 0, c = 0, = 35 , dry = 16 kN/m and sat = 20 kN/m is approximately equal to
10m
8m
30
(a)
47.
0.70
(b)
0.80
(c)
1.00
(d) 1.20
Match the following groups
Group = I
Group - II
P
Q
R
S
(a)
(c)
48.
Constant head permeability test
Consolidation test
Pycnometer test
Negative skin friction
P-4, Q-3, R-2, S-1
P-3, Q-4, R-2- S-1
1.
2.
3.
4.
(b)
(d)
Pile foundations
Specific gravity
Clay soil
Sand
P-4, Q-2, R-3, S-1
P-4, Q-1, R-2, S-3
The bearing capacity of a rectangular footing of plan dimensions 1.5 m x 3m resting on the surface of
22
a sand deposit was estimated s 600 kN/m of a sand deposit was estimated as 600 kN/m when the
2
water table is far below the base of the footing. The bearing capacities in kN/m when the water level
rises to depths of 3m, 1.5 m and 0.5 m below the base of the footing are
(a)600, 600, 400 (b)600, 450, 350 (c)600, 500, 250 (d)600, 400, 250
What is the ultimate capacity in kN of the pile group sown in the figure assuming the group to fail as
a single block ?
49.
10m
0.4m diameter piles
Clay soil
Cu = 40kN/m
2
1.2m c/c
1.2m c/c
(a)
921.6
(b)
1177.6
(c)
2438.6
(d)
3481.6
Page 7 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
50.
A horizontal water jet with a velocity of 10 m/s and cross sectional area of 10 mm strikes a flat plate
held normal to the flow direction. The density of water is 1000 kg/m3. The total force on the plate
due to the jet is
(a)
51.
100 N
(b)
10 N
(c)
1N
(d)
0.1 N
2
A 1: 50scale model of a spillway is to be tested in the laboratory. The discharge in the prototype is
3
1000 M /s. The discharge to be maintained in the model test is
(a)
0.057 m /s
3
(b)
0.08m /s
2
(c)
0.57 m /s
3
(d)
5.7 m /s
3
52.
A triangular open channel has a vertex angle to 90and carries flow at a critical depth of 0.30 m. The
discharge in the channel is
(a)
0.08 m /s
3
(b) 0.11 m /s
3
3
(c)
0.15 m /s
3
(d) 0.2 m /s
3
3
53.
Flow rate of a fluid (density = 1000 kg/m ) in a small diameter tube is 800 mm /s. The length and
the diameter of the tube are 2 m and 0.5 mm, respectively. The pressure drop in 2 m length is equal
to 2.0 MPa. The viscosity of the fluid is
(a)
0.025 N.s/m
2
(b)
0.012 N.s/m
2
(c)
0.00192 N.s/m (d)
3
2
0.00102 N.s/m
2
54.
The flow rate in a wide rectangular open channel is 2.0 m /s per metre width. The channel bed slope
is 0.002. The Manning’s roughness coefficient is 0.012. The slope of the channel is classified as
(a)
Critical
(b)
Horizontal
(c)
Mild
(d)
Steep
55.
The culturable command area for a distributary channel is 20,000 hectares. Wheat is grown in the
entire area and the intensity of irrigation is 50%. The kor period for wheat is 30 days and the kor
water depth is 120 mm. The outlet discharge for the distributary should be
(a)
2.85 m /s
3
(b)
3.21 m /s
3
(c)
4.63 m /s
3
(d) 5.23 m /s
3
56.
An isolated 4-hour storm occurred over a catchment as follows
2 hour3 hour4 hour1 hour
Rainfall (mm)928127
The index for the catchment is 10 mm/h. The estimated runoff depth from the catchment due to
the above storm is
(a)
10 mm
(b)
16 mm
(c)
20 mm
(d)
23 mm
Time
st
nd
rd
th
57.
Two electrostatic precipitators (ESPs) are in series. The fractional efficiencies of the upstream and
downstream ESPs for size dp are 80% and 65%, respectively. What is the overall efficiency of the
system for the same dp?
(a)
100%
(b)
93%
(c)
80%
(d)
65%
58.
50 g of CO2 and 25 g of CH4 are produced from the decomposition of municipal solid waste (MSW)
with a formula weight of 120 g. What is the average per capita green house gas production in a city
of 1 million people with a MSW production rate of 500 ton/day ?
(a)
104 g/day
(b)
120 g/day
(c)
208 g/day
(d)
313 g/day
59.
The extra widening required for a two-lane national highway at a horizontal curve of 300 m radius,
considering a wheel base of 8 m and a design speed of 100 kmph is
(a)0.42 m(b)0.62 m(c)0.82 m(d)0.92 m
Page 8 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
60.
While designing a hill road with a ruling gradient of 6%, if a sharp horizontal curve of 50 m radius is
encountered, the compensated gradient at the curve as per the Indian Roads Congress specifications
should be
(a)4.4%(b)4.75%(c)5.0%(d)5.25%
The design speed on a road is 60 kmph. Assuming the driver reaction time of 2.5 seconds and
coefficient of friction of pavement surface as 0.35, the required slopping distance for two-way traffic
on a single lane road is
(a)82.1 m(b)102.4 m(c)164.2 m(d) 186.4 m
The width of the expansion joint is 20 mm in a cement concrete pavement. The laying temperature is
20C and the maximum slab temperature in summer is 60C. The coefficient of thermal expansion of
-6o
concrete is 10×10 mm/mm/ C and the joint filler compresses up to 50% of the thickness. The
spacing between expansion joints should be
(a)20 m(b)25 m(c)30 m(d)40 m
The following data pertains to the number of commercial vehicles per day for the design of a flexible
pavement for a national highway as per IRC:37-1984
Type of commercial Number of vehicles per day
Vehicle Damage Factor
Vehicle considering the number f lanes
Two axle trucks2000 5
Tandem axle trucks200 6
Assuming a traffic growth factor of 7.5% per annum for both the types of vehicles, the cumulative
number of standard axle load repetitions (in million) for a design life of ten years is
(a)44.6(b)57.8(c)62.4(d)78.7
64.
Match the following tests on aggregate
TEST
P.Crushing test
Q.Los Angeles abrasion test
R.Soundness test
S.Angularity test
(a)P-2, Q-1, R-4, S-3
(c)P-3, Q-2, R-1, S-4
and its properties
PROPERTY
1.Hardness
2.Weathering
3.Shape
4.Strength
(b)P-4, Q-2, R-3, S-1
(d)P-4, Q-1, R-2, S-2
61.
62.
63.
65.
The plan of a map was photo copied to a reduced size such that a line originally 100 mm, measures
90 mm. The original scale of the plan was 1 : 1000. The revised scale is
(a)1 : 900(b)1 : 111(c)1 : 1121(d)1: 1221
The following table gives data of consecutive co-ordinates in respect of a closed theodolite traverse
PQRSP.
StationNorthing, mSouthing, mEasting, mWesting, m
P400.75300.5
Q100.25199.25
R199.0399.75
S300.0200.5
The magnitude and direction of error of closure in whole circle bearing are
(a)
(c)
2.0 m and 45
2.82 m and 315
(b)
(d)
2.0 m and 315
3.42 m and 45
66.
Page 9 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
67.
The following measurements were made during testing a leveling instrument.
Instrument at
P
Q
P1
2.800 m
2.700 m
Staff Reading at
Q1
1.700 m
1.800 m
P1 is close to P and Q1 is close to Q. If the reduced level of station P is 100.000 m, the reduced level
of station Q is
(a)
68.
99.000 m
(b)
100.000 m
(c)
101.000 m
(d)
102.000 m
Two straight lines intersect at an angle of 60. The radius of a curve joining the two straight lines is
600m. The length of long chord and mid-ordinates in metres of the curve are
(a)
8.4, 600.0
(b)
600.0, 80.4
(c)
600.0, 39.89
(d)
40,89, 300
69.
The magnetic bearing of a line AB is S 45E and the declination is 5West. The true bearing of the
line AB is
(a)
S 45E
(b)
S 40E
(c)
S 50E
(d)
S 50W
COMMON DATA QUESTIONS
Common Data for Questions 70,71
Water is flowing through the permeability apparatus as shown in the figure. The coefficient of permeability of
the soil is k m/s and the porosity of the soil sample is 0.50.
70.
The total head, elevation head and pressure head in metres of water at the point R shown in the
figure are
(a)0.8, 0.4, 0.4(b) 1.2, 0.4, 0.8(c)0.4, 0, 0.4(d)1.6, 0.4, 1.2
What are discharge velocity and seepage velocity through the soil sample ?
(A)k, 2k(B)2/3k, 4/3k(C)2k,k(D)
4/3k, 2/3k
71.
Common Data for Questions 72 and 73 :
Ordinates of a 1-hour unit hydrograph at 1 hour intervals, starting from time t = 0, are 0, 2, 6, 4, 2, 1 and 0
3
m /s.
72.
Catchment area represented by this unit hydrograph is
22
(a) 1.0 km(b)2.0 km(c)
3.2 km
2
(d)
5.4 km
3
2
73.
Ordinate of a 3-hour unit hydrograph for the catchment at t= 3 hours is
333
(a)2.0 m /s(b)3.0 m /s(c)4.0 m /s(d)
5.0 m /s
Page 10 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
Common Data for Questions 74 and 75 :
A completely mixed activated sludge process is used to treat a wastewater flow of 1 million litres per day (1
MLD) having a BOD5 of 200 mg/L. The biomass concentration in the aeration tank is 2000 mg/L and the
3
concentration of the net biomass leaving the system is 50 mg/L. The aeration tank has a volume of 200 m .
74.
75.
What is the hydraulic retention time of the wastewater in aeration tank ?
(a)0.2 h(b)4.8 h(c)10 h(d)
What is the average time for which the biomass stays in the system ?
(a)5h(b)8h(c)2 days
(d)
24 h
8 days
Linked Answer questions : Q.76 to Q.85 carry two marks each.
Statement of Linked Answer Questions 76 and 77.
A two span continuous beam having equal spans each of length L is subjected to a uniformly distributed load
w per unit length. The beam has constant flexural rigidly.
76.
77.
The reaction at the middle support is
5L
(a)L(b)
2
The bending moment at the middle support is
22
(b)8wL(a)4wL
(c)
(c)
5L
4
(d)
2
L2
16
12wL
(d)
16wL
2
Statement for Linked Answer Questions 78 and 79
A singly reinforced rectangular concrete beam has a width of 150 mm and an effective depth of 330 mm. The
characteristics compressive strength of concrete is 20 MPa and the characteristics tensile strength of steel is
415 MPa. Adopt the stress block for concrete as given in IS 456-2000 and take limiting value of depth of
neutral axis as 0.48 times the effective depth of the beam.
78.The limiting value of the moment of resistance of the beam is kN.m is
(A)0.14(B)0.45(C)45.08(D)156.82
79
The limiting area of tension steel in mm is
(A)473.9(B)412.3
2
(C)
373.9
(D)
312.3
Statement for Linked Answer Questions 80 and 81
The ground conditions at a site are as shown in the figure. The water table at the site which was initially at a
depth of 5m below the ground level got permanently lowered to a depth of 15m below the ground level due
to pumping of water over a few years. Assume the following data
3
i.unit weight of water = 10kN/m
3
ii.unit weight of sand above water table = 18kN/m
3
iii.unit weight of sand and clay below the water table = 20kN/m
2
iv.coefficient of volume compressibility = 0.25m /MN
Page 11 of 12
GATE 2007 Civil Engineering Question Paper
GATE CIVIL ENGINEERING 2007 (CE)
80.
What is the change in the effective stress in kN/m2 at mid-depth of the clay layer due to the lowering
of the water table?
(A)0(B)20(C)80(D)100