Name ______Per. _____
How Glaciers Erode andTransport Sediment
After you have read the article about how glaciers erode and transport sediment, answer the following questions:
1.What is Freeze-Thaw?
2.What is Plucking, and where about would it occur in a glacier?
3. What is abrasion and why is it an important cause of glacial erosion?
4. What are the main sources of rock debris found on, in and under a glacier?
5.What role do crevasses play in the erosional process?
6.What are shear plains and what can they do to englacial sediment?
7.The surface of a glacier is often littered with rock debris of all shapes and sizes. In a river, you might expect some of this material to become rounded as it moves down stream, but in a glacier most of the material is rough and angular. Why do you think that the surface debris is both angular and of such a wide range of sizes?
How Glaciers Erode and Transport Sediment
As a glacier moves, particularly a warm glacier, it causes erosion of the underlying surface. However, ice doesn't seem as if it should be a particularly effective material for wearing away hard rocks, so how do glaciers manage to produce such large erosional features?
Material from underlying bedrock or sediment is picked up by the glacier and 'held' in the ice as it moves. Material falling onto the surface (often the result of freeze-thaw activity, or frost shattering, on the surrounding rock walls) is also transported, and often finds its way down through crevasses to the base of the glacier. Material held within the glacier is called 'englacial moraine'. It is this material trapped in the ice that allows the glacier to erode its surroundings.
With its load of abrasive rock fragments, the base of the glacier acts like a belt sander, scraping across the rock, eroding it, producing characteristic erosional features, and creating a supply of material that leads eventually to the formation of depositional features as well. This scraping process is called Abrasion.
Occasionally, a moving glacier may become stuck on its bed. This occurs when for some reason a reduction in pressure causes liquid water to freeze, attaching the moving ice to the bedrock. As the ice continues to move an immense pulling, force is applied to the attached rock, which may then fracture and be plucked from its position.
The range of size of particles that can be carried by a glacier is tremendous, ranging from very fine, ground up rock termed rock flour to massive boulders.
Rock flour is so prevalent in the melt water of some glaciers that the water is unsafe to drink. This is especially so in areas where the rocks contain high concentrations of mica, such as the Garnet Mica Schist of Svartissen. To avoid stomach problems it's advisable to use a hose to drink water from below the surface of streams, since the majority of the mica flour floats in the upper few centimeters of the water.
At the other end of the scale, a glacier can carry rocks hundreds of meters in diameter. These are usually from sources on the valley walls and fall onto the glacier rather than being plucked out of the underlying bedrock.
Large rock being moved by an Alpine glacier. The figure on the right is almost 6 feet tall
Although the surfaces of glaciers can seem to consist of nothing but rock debris, most of the debris in a mature glacier is concentrated near its base. In fact, basal ice may consist of only one part ice to every nine of sediment.
The reason that the surfaces often seem so well coated in moraine is two fold. First, the surface is the obvious place for debris from the valley walls to accumulate, and secondly, the surface is subjected to solar heating and melting.
As the surface warms up, ice melts and runs off via a network of surface streams. Much of the larger intra-glacial debris that drops out of the melting ice remains on the surface for a period of time. Some of this material will find its way down through crevasses and holes to aid the erosion of the bedrock, the rest will be covered by winter snows, possibly to appear again in another summer melt. During the summer, the effects of melting can produce interesting features. Small dark rocks can warm up faster than the surrounding ice, and melt their way into the surface of the glacier, where as larger rocks, especially light colors ones, may be slow to warm up and thus protect the ice below them. This leads to the formation of bumps and tables with a rocky surface and an ice column beneath.
Running water is very common on and within glaciers. Snow and ice that melts on the surface of the ice, or is generated by melting at the base, commonly forms extensive channels on, within, or beneath the glacier. This flowing water also transports a considerable amount of sediment to the snout of the glacier.
Near the glacier, snout debris also tends to move upwards along shear planes within the ice; curved surfaces, which are due to the faster movement of ice above each plane relative to the ice below the plane, reversing the general burying of debris.
Light colored rock protecting snow beneath it from solar heating, whilst surrounding snow has melted
Black lines of debris mark the shear planes within the ice of a glacier snout