Q40 Fencing & Gates
Supplied by Lang+Fulton (formerly Orsogril UK)
Head office / Technical & Sales: Lang+Fulton, Newbridge Industrial Estate, Newbridge, Edinburgh EH28 8PJ
Distribution: Cygnus Point, Black Country New Road, West Bromwich B70 0BD
Tel 0131 441 1255; Fax 0131 441 4161; ; www.langandfulton.co.uk
Product Types
Steel Grating Fences to BS 1722: Part 14 except as varied below or on drawings
1. Roma-2; (previously Sterope)
2. Roma-3 (previously Sterope)
3. Roma-4 (previously Britosterope)
4. Verona (previously Pleione)
5. Genoa (previously Alcione)
6. Palermo (previously Dione)
7. Arezzo-25 barrier fencing (previously Potissimum)
8. Novara-34 anti-climb fencing (previously Potissimum)
9. Novara-25 anti-climb fencing (previously Potissimum)
10. Torino
11. Roma-4HS higher security (Britosterope)
12. Palermo-HS higher security (Dione)
13. Bespoke Grating Fence
Steel Louvre Fences to BS 1722: Part 14 except as varied below or on drawings
14. Italia-80 (previously Talia-80)
15. Italia-80V (previously Talia-80 Vertical)
16. Italia-100 (previously Talia-100)
17. Italia-100V (previously Talia-100 Vertical)
18. DeltaWing
19. DeltaBox
20. DeltaFoil
Steel Railing Fences to BS 1722: Part 9 for mild steel anti climb fences with round verticals and flat horizontals except as varied below or on drawings
21. Modena (previously Anticlea)
22. Siena (previously Acumina)
23. Siena Sport (previously Acumina Sport)
24. Bespoke Railing Fence
Steel Gates to BS1722-9:2000 and –14 except as varied below or on drawings
25. Single Leaf Gate
26. Double Leaf Gate
27. Pivot Gate
28. Sliding Gate
29. Cantilevered Sliding Gate
1. ROMA-2 (previously Sterope)
Roma-2: fence with aperture of 63x132mm, made up of 25x2mm vertical flat bars and 5mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 930 / 1195 / 1320 / 1460 / 1720 / 1985mm high x 1992mm wide (achieving nominal heights of 1.0 / 1.25 / 1.4 / 1.5 / 1.8 / 2.0m x 2.0m wide when framed and fixed)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 50mm Ø tubular posts for panel heights of 930 / 1195 / 1320 / 1460mm
b) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
c) 80x8mm flat bar, 80x40mm RHS or 76mm Ø tubular posts for panel heights of 1985mm
d) 60x60, 80x80mm SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).
Height from ground: panels to sit maximum 100mm off ground
Changes in level: fence panels stepped to a maximum of 150mm on standard length post. Post centres to be reduced for steeper gradients (between 1:20 and 1:7)
Changes in direction: 60x60, 80x80mm SHS or RSA for 90° corner post. Two flat bar posts for other angles.
2. ROMA-3 (previously Sterope)
Roma-3: fence with aperture of 63x132mm, made up of 25x3mm vertical flat bars and 5mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 930 / 1195 / 1320 / 1460 / 1720 / 1985mm high x 1992mm wide and 2123 / 2387mm high x 2022mm wide (achieving nominal heights of 1.0 / 1.25 / 1.4 / 1.5 / 1.8 / 2.0 / 2.2 / 2.4m)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 50mm Ø tubular posts for panel heights of 930 / 1195 / 1320 / 1460mm
b) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
c) 80x8mm flat bar, 80x40mm RHS or 76mm Ø tubular posts for panel height of 1985mm
d) 80x40mm RHS or 76mm Ø tubular posts for panel heights of 2123 / 2387mm
e) 60x60, 80x80mm SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).
Height from ground: panels to sit maximum 100mm off ground
Changes in level: fence panels stepped to a maximum of 150mm on standard length post. Post centres to be reduced for steeper gradients (between 1:20 and 1:7)
Changes in direction: 60x60, 80x80mm SHS or RSA for 90° corner post. Two flat bar posts for other angles.
3. ROMA-4 (previously Britosterope)
Roma-4: fence with aperture of 63x132mm, made up of 30x4mm vertical flat bars and 6mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 1720 / 1985 high x 1992mm wide and 2123 / 2387mm high x 2022mm wide (achieving nominal heights of 1.8 / 2.0 / 2.2 / 2.4m)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
b) 80x8mm flat bar, 80x40mm RHS or 76mm Ø tubular posts for panel height of 1985mm
c) 80x40mm RHS or 76mm Ø tubular posts for panel heights of 2123 / 2387mm
d) 60x60, 80x80mm SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).
Height from ground: panels to sit maximum 100mm off ground
Changes in level: fence panels stepped to a maximum of 150mm on standard length post. Post centres to be reduced for steeper gradients (between 1:20 and 1:7)
Changes in direction: 60x60, 80x80mm SHS or RSA for 90° corner post. Two flat bar posts for other angles.
4. VERONA (previously Pleione)
Verona: fence with aperture of 63x66mm, made up of 25x2mm vertical flat bars and 5mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 930 / 1195 / 1320 / 1460 / 1720 / 1991mm high x 1992mm wide and 2123 / 2387mm high x 2022mm wide (achieving nominal heights of 1.0 / 1.25 / 1.4 / 1.5 / 1.8 / 2.0 / 2.2 / 2.4m)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 50mm Ø tubular posts for panel heights of 930 / 1195 / 1320 / 1460mm
b) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
c) 80x8mm flat bar, 80x40mm RHS or 76mm Ø tubular posts for panel height of 1985mm
d) 80x40mm RHS or 76mm Ø tubular posts for panel heights of 2123 / 2387mm
e) 60x60, 80x80mm SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).
Height from ground: panels to sit maximum 100mm off ground
Changes in level: fence panels stepped to a maximum of 150mm on standard length post. Post centres to be reduced for steeper gradients (between 1:20 and 1:7)
Changes in direction: 60x60, 80x80mm SHS or RSA for 90° corner post. Two flat bar posts for other angles.
5. GENOA (previously Alcione)
Genoa fence with aperture of 126x132mm, made up of 25x3mm vertical flat bars and 5mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 930 / 1331 / 1720mm high x 1992mm wide (achieving nominal heights of 1.0 / 1.4 / 1.8m x 2.0m wide when framed and fixed)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 50mm Ø tubular posts for panel heights of 930 / 1320mm
b) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
d) 60x60 SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).
Height from ground: panels to sit maximum 100mm off ground
Changes in level: fence panels stepped to a maximum of 150mm on standard length post. Post centres to be reduced for steeper gradients (between 1:20 and 1:7)
Changes in direction: 60x60 SHS or RSA for 90° corner post. Two flat bar posts for other angles.
6. PALERMO (previously Dione)
Palermo: fence with aperture of 43x44mm, made up of 25x2mm vertical flat bars and 5mm diameter horizontal round bars, framed top and bottom with flat bars bent over at ends to form fixing lugs for a bolted panel to post connection.
Manufacture & Material
Electrofused steel S235JR
Panel and Post Dimensions
Panels: Standard heights 930 / 1195 / 1320 / 1460 / 1720 / 1991mm x 1992mm wide and 2123 / 2387mm high x 2022mm wide (achieving nominal heights of 1.0 / 1.25 / 1.4 / 1.5 / 1.8 / 2.0 / 2.2 / 2.4m)
Posts:
a) 60x7mm flat bar, 50x30mm RHS or 50mm Ø tubular posts for panel heights of 930 / 1195 / 1320 / 1460mm
b) 60x7mm flat bar, 50x30mm RHS or 76mm Ø tubular posts for panel height of 1720mm
c) 80x8mm flat bar, 80x40mm RHS or 76mm Ø tubular posts for panel height of 1985mm
d) 80x40mm RHS or 76mmØ tubular posts for panel heights of 2123 / 2387mm
e) 60x60, 80x80mm SHS or RSA for corners
Special panel sizes: fabricated to size by Lang+Fulton following site survey or cut on site and fixed to posts with Lang+Fulton adjustable lug
Finishing
Options:
(a) hot dip galvanized to BS EN ISO 1461
(b) hot dip galvanized to BS EN ISO 1461 and polyester powder coated to BS EN 13438 in any standard RAL colour
Installation
Fastenings: panels fixed to posts with M10x30mm stainless steel bolts with domed heads and snap-off security nuts, all stainless steel grade A2
Groundwork: refer to BS 1722 and always consider existing ground conditions, but posts set in holes not less than 300mm square in plan, depth not less than 500mm, completely filled to a minimum of 50mm below ground level with concrete mix (minimum strength of C30).