1410 N. Hilton, Boise, ID 83706
For assistance, call the
Air Permit Hotline – 1-877-5PERMIT / Emissions Units - Spray Paint Booth Information Form EU3
Revision 6
12/15/16
Complete this form for each paint booth. Please see instructions on page 2 before filling out the form.
IDENTIFICATION1. Company Name: / 2. Facility Name:
3. Brief Project Description:
BOOTH INFORMATION
4. Booth Data: / New Booth Unpermitted Existing Booth If an existing booth, when was it installed?
Modification to a Permitted Booth, Permit #: Date Permit Issued:
Dry Filters? Dry Filters w/ a Wet Wall? Wet Wall only? Other, provide details:
Booth Airflow Type: Down draft Semi-Downdraft Side draft Other, provide details:
5. Booth Information: Manufacturer: Model: Date Manufactured:
6. Is the booth equipped with a heater? No Go to the next section Yes If “yes”, answer the following questions.
Heating method: Electricity, Go to the next section Combustion
Who is the manufacturer of the booth heater? What is the model number of the booth heater? ______
What is the heat input rating of the booth heater? MMBtu/hr What fuel is used in the booth heater (i.e., natural gas or LPG)?
SPRAY GUN DESCRIPTION AND SPECIFICATIONS
7. Gun No. / 8. Manufacturer / 9. Model / 10.Type (e.g. HVLP, airless, conventional) / 11.Gun Transfer Efficiency % per the manufacturer
1
2
3
4
12. Number of guns to be used simultaneously?
SPRAY MATERIAL DESCRIPTION AND SPECIFICATIONS
12. Type of Spray Material Used / 13. Type of Material Coated / 14. Max. Usage (gal/day) / 15. Solid TAP/HAP Content (lb/gal) / 16. VOC TAP/HAP Content (lb/gal)
EMISSION CONTROL DEVICE (FILTER b) DESCRIPTION AND SPECIFICATIONS
17. Stack Served / 18. Filter Manufacturer / 19. Model / 20. PM Control Efficiency (%)a
Notes: / a. Provide either stack test data or vendor’s documentation to support the control efficiency specified above.
b. Fill out and submit appropriate control equipment form(s) if this booth has a control device(s) other than a filter system.
REQUEST FOR PERMIT LIMITATIONS AND HOUS OF OPERATIONS
21. Are you requesting any permit limits? / No Yes. If Yes, check all that apply below and fill in requested limit(s):
Operation Hour Limits: / Production Limits:
Material Usage Limits: / Other:
22. Rationale for Requesting the Limit(s):
Page 1
Instructions for Form EU3
Please refer to IDAPA 58.01.01.220 for a list of the general exemption criteria for Permit to Construct exemptions.1 – 3. Provide the same company name, facility name (if different), and brief project description.
USE ATTACHMENT IF ADDITIONAL SPACE IS REQUIRED.
Booth Information:
4. Check whether this booth is a new booth to be constructed, an unpermitted existing booth (as-built) applying for a permit for the first time, or a permitted source to be modified, what type of filters, and the booth configuration.
5. Please provide the date of construction of the booth in month/day/year in which construction or modification begins as defined in EU0 Form Instruction item 7.
6. Specify heater details if the booth uses a heater.
Spray Gun Description and Specifications:
7. Specify the gun number.
8. Specify manufacturer(s) of the spray gun(s) used in your booth.
9. Specify the model(s) of the spray gun(s).
10. Indicate the type of the gun(s). The type can be airless, HVLP, air atomization, electrostatic/air atomization, etc.
11. Indicate the minimum transfer efficiency of the painting operation as specified by the manufacturer.
Spray Material Description and Specifications (Use Attachment if Additional Space is Required):
12. List all the coating materials used in this booth including enamel, lacquer, clean-up solvent, primer, etc. A product formulation data sheet (provided from the manufacturer), Material Safety Data Sheet (MSDS), or Safety Data Sheet (SDS) should be attached with the application for each painting material used in the booth.
13. For each coating material indicate all of the types of material that are being coated as being metal, wood, plastic, etc.
14. For each coating material indicate the maximum usage of the materials listed in Item 8 in gallons per day.
15. For each coating material indicate the maximum solid toxic air pollutant/hazardous air pollutant (TAP/HAP) content that is used, or expected to be used, in pounds per gallon as it is applied.
16. For each coating material indicate the maximum volatile organic chemicals (VOC) TAP/HAP content that is used, or expected to be used, in pounds per gallon as it is applied.
Emission Control Device (filter) Description and Specifications:
17. Provide the name of the stack served.
18. Provide the name of the filter manufacturer.
19. Provide the model of the filter according to manufacturer's literature.
20. Provide the control efficiency for particulate matter.
Request for Permit limitations:
21. If you wish to have permit limits placed on the paint booth, mark “Yes.” Check each type of limit that applies to this emission unit and fill in the requested limit. For example, production limits may be in terms of parts produced per year, material usage limits may be in gallons per day.
22. Provide rationale for any requested limit(s). This helps the DEQ and the applicant determine whether the limits are necessary, and whether they will accomplish the desired purpose.
Page 2