Instrumentation Mechanician

Trade Test Centre Accreditation Checklist

Accrediting ETQA / e.g. QCTO or SETA Name
TTC Name:
Centre Manager Name
TTC Contact Details
TTC Physical Address / e.g. 17 Tonga-tinge Street, Mable Hall, 1612
Assessor/Lecturer Name
Assessor qualification relevant to the trade
SME Name
SME Employer Details
SME Employer contact
Ratio of candidates to Assessor / e.g. 12 Candidates:1 Facilitator
No. of Candidates per given time in the Venue
Accreditation History (If previously accredited through the SETA System, Complete the section below )
Accredited by: / SETA Name / Accreditation No.
Accreditation Visit Date: / DD/MM/CCYY / OFO Code (if applicable)
Province / e.g. Northern Cape / Municipality / e.g. Madibeng
New Accreditation Information
Trade Test / X / OFO Code
Accreditation Date / DD/MM/YYYY
Urban / X / Rural / X
Item Description / Ratio / Y / N / Acceptable/Not Acceptable /
Hand Tools
Circuit board stand / 1:1
Soldering station / 1:1
Set screw drivers flat / 1:1
Set screw drivers Philips / 1:1
Set Allen keys 1.5mm – 10mm / 1:1
Crimping tool ratchet type insulated / 1:1
Engineer’s square 100mm / 1:1
Padlock and key / 1:1
Pliers – combination insulated 200mm / 1:1
Pliers – diagonal cutting 200mm / 1:1
Pliers – gas non-insulated 200mm / 1:1
Pliers – long nose insulated 200mm / 1:1
Pliers – round nose insulated 150mm / 1:1
Set Flat screw drivers 6 piece / 1:1
Set Phillips screw drivers 6 piece / 1:1
Set spanners tube 0BA – 10BA / 1:1
Set spanners: 6-22 (flat ring) / 1:1
Shifting spanner/ Adjustable wrenches / 1:1
Tape –steel 5m / 1:1
Retractable knife / 1:1
5 Tier Toolbox / 1:1
Vice grip 250mm / 1:3
Wire stripper spring assisted insulated / 1:1
Bastard file 300mm plus file handle / 1:1
Second cut 300mm plus file handle / 1:1
Smooth file 300mm plus file handle / 1:1
Round file 400mm plus file handle / 1:1
Comments:
Special Tools
Power supply (3V, 6V, 9V, 12V and 24V) / 1:1
Function generator / 1:1
Oscilloscope / 1:1
Comments:
Measuring Equipment
Digital Multimeter / 1:1
Spirit Level / 1:1
Comments:
Machinery
Pneumatic simulator with the capability of doing flow, hydrostatic level and purge type level control.
Must have sensor, controller and valve minimum. / 1:1
·  Loop drawings for each loop (must be available if required) / 1:1
Pneumatic dP cell (may be separate from simulator) / 1:1
Pneumatic control valve
(may be separate from simulator) / 1:1
Tools and manuals to calibrate dP cell / 1:1
·  Pneumatic calibrator (manometer, etc.) / 1:1
·  Conversion table/ Symbol sheet (ISO 3511/1/2/3) / 1:1
Copper tubing, fittings, nuts and ferrules / 1:1
Flexible tubing / 1:1
Pipe bender / 1:1
Pipe cutter / 1:1
Pre-bent tubing for simulator (must be available if required) / 1:1
Electronic simulator with the capability of doing flow, level, and cascade type level control. Must have flow and level transmitters, pressure switch, 2 X controllers, PLC, trips and alarms and valve minimum / 1:1
Electronic transmitter (may be separate from simulator) / 1:1
Flow sensor/ transmitter (may be separate from simulator) / 1:1
Pressure switch (may be separate from simulator) / 1:1
Tools, manuals, programmer (if applicable) and equipment to calibrate, fault find or configure electronic equipment) / 1:1
Conversion table/ Symbol sheet (ISO 3511/1/2/3) / 1:1
Loop drawings for each loop (must be available if required) / 1:1
Pneumatic calibrator (manometer, etc.) / 1:1
PC to program PLC / 1:1
Configuration and data sheets for all equipment used in the application. / 1:1
Selection of RTD’s and Thermocouples / 1:1
Data Sheets for RTD’s and Thermocouples / 1:1
Temperature measuring device (Controller and Indicator) / 1:1
Analogue Multimeter / 1:1
Millivolt source / 1:1
Heat source (Urn, Kettle, Oven, etc.) / 1:1
Compensating Leads / 1:1
Comments:
Equipments (Long Term Consumables)
Soldering Iron / 1:1
Solder sucker / 1:1
Soldering Iron station / 1:1
Comments:
Consumables
Electronic components / 1:1
Vero board (50mm X 50mm) / 1:1
Solder / 1:1
Wire (Red and Black) / 1:1
Resistors / 1:1
Transistors / 1:1
Capacitors / 1:1
Diodes / 1:1
Insulation tape / 1:1
Red wire / 1:1
Black wire / 1:1
Mystery Box / 1:1
T – Pieces / 1:1
Crocodile clamps (wire) / 1:1
Banana clamps (wire) / 1:1
Comments:
Safety
Safety boots (Pair) / 1:1
Personal Protective Clothing (Suit) / 1:1
Safety glasses / 1:1
Comments:
Logistics And Lay-Out
Cubicles proportional to the number of candidates tested
Panel proportional to the number of candidates tested
Class rooms for theoretical training
Workshops for practical training
Teaching media including:
·  Projectors
·  White boards
·  Stationery
·  Models samples
·  Green boards/ Notice Boards
Demarcations
Comments:

I ……………………………………… the undersigned, hereby declare that all the tools/equipment/trade test materials/machines which were checked are the sole property of the TTC.

Accreditation recommended / Yes / No
Constraints/Gaps: ______
Recommendations: ______
SME Name
Signature / Date: DD/MM/CCYY
Organizational Rep. Name
Designation
Signature / Date DD/MM/CCYY

Page 8 of 8