Overhead Coiling Doors and Grilles

SECTION 08330

OVERHEAD COILING DOORS AND GRILLES

Display hidden notes to specifier. (Don't know how? Click Here)

** NOTE TO SPECIFIER ** Porvene Doors, Inc.; industrial, commercial, service doors, coiling grilles and insulated rolling doors.
.
This section is based on the products of Porvene Doors, Inc., which is located at:
14241 Grant St.
Moreno Valley, CA 92553
Tel: 877-906-3999
Fax: 877-343-6677
Email: request info ()
Web: www.porvenedoors.com
[ Click Here ] for additional information.
The original company was formed in 1948 as Porcelain Veneer Inc., manufacturing exterior porcelain panels for the service station industry. In 1952, the Company added architectural facing to its product line by manufacturing sun and shade screens for the high rise industrial and commercial buildings. In 1968 the Company added continuous steel sheet doors to its product line. This door revolutionized the door industry and with this success the Company put all its resources in this product line and formed a new Company as Porvene Roll-A-Door, Inc. In 1993 the Company was restructured and changed its name to Porvene Doors, Inc.
Since 1968, the Company has been the leader in the continuous steel sheet door and has branched out into the Heavy Duty Rolling Steel Slat Door. In 1990 the Company introduced this product line with the same high standards that were used in the introduction of the continuous steel sheet door. The design and operation features of the slat door are superior within the industry and can meet the needs and requirements of most applications. The Company has also introduced a Rolling Grille and a Steel Backed Insulated Rolling Steel Door with the same high standards as its other products. In 2011, Porvene introduced a line of Commercial Sectional doors. The line includes Standard Lift, High Lift, Vertical Lift, and soon to be Insulated Steel Backed Door to be introduced in 2012.
Porvene provides its dealers, when needed, calculations on environmental LEED (U.S. Green Building Council). It also offers, when called for in specifications, seismic calculations to meet our customer's needs.
As a leader within the industrial and commercial door industry, the Company will always manufacture a superior product with innovative designs and techniques to meet our customer's needs.200 Series: This product can be insulated, wind locked, and built with a wicket door. The complete line is available, depending on size, as hand operated or chain operated and can be upgraded to electric operation.
300 Series: Offers the economy of a sheet door with the added strength of a service door. Available with 22 or 24 gauge steel slat curtain (some sizes available only in 24 gauge) and can be wind locked. The complete product line comes standard with chain operation and can be upgraded to electric operation.
400 Series: Offers 24, 22, 20 and 18 gauge slats for additional strength. Our new and innovated slat design reduces the snapping sounds that come from metal to metal contact common to rolling steel slat doors when opening and closing. The product line comes standard with chain operation and can be upgraded to electric operation.
500 Series: Coiling grille constructed using aluminum tubes over solid steel rods giving added strength for security and features low friction nylon blocks mounted to the bottom bar for quiet operation. The complete line is available, depending on size, as hand operated or chain operated and can be upgraded to electric operation.
600 Series: Offers insulating values of R-Factor = 5.4 and U-Factor = 0.185. The insulation material is made from environmentally safe polyisocyanurate with aluminum facers adhered to the effective thermal barrier. The product line comes standard with chain operation and can be upgraded to electric operation.

PART 1 GENERAL

1.1 SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

A. Upward coiling industrial sheet doors.

B. Upward coiling commercial slat doors.

C. Upward coiling service doors.

D. Upward coiling insulated Industrial sheet doors.

E. Upward coiling insulated service doors.

F. Upward coiling quiet glide grilles.

1.2 RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

A. Section 05500 - Metal Fabrications: Metal supports and headers.

** NOTE TO SPECIFIER ** Delete if motorized coiling doors not required.

B. Section 16050 - Basic Electrical Materials and Methods: Service and connection to operator. Empty raceway for remote control and safety equipment.

1.3 REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

A. ASTM A 1018 - Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability.

** NOTE TO SPECIFIER ** Delete two paragraphs below if coiling grille not required.

B. ASTM B 241 - Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube.

C. ASTM B 597 - Standard Practice for Heat Treatment of Aluminum Alloys.

1.4 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's specifications and technical data including the following.

1. Detailed specification of construction and fabrication, gauge and type of metal; parts list; name, address, and phone number of installing distributor; and operating and maintenance instructions.

** NOTE TO SPECIFIER ** Delete paragraph below if motorized coiling doors not required.

2. Include electrical characteristics of components and voltage requirements provided by other, but required to operate assembly.

3. Installation methods including size and location of mounting bolts.

4. Brochure.

C. Shop Drawings: Indicate dimensions, description of materials and finishes, general construction, specific modifications, anchorage methods, hardware, including specific requirements indicated.

1. Indicate location of motor operator.

2. Height and width dimensions, and jamb conditions.

3. Opening sizes.

4. Details of slats.

5. Track, jambs, and hardware.

D. Selection Samples: For each finish specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns, if requested.

1.5 QUALITY ASSURANCE

A. Installer Qualifications:

1. Acceptable to or licensed by manufacturer

** NOTE TO SPECIFIER ** Delete if motorized coiling doors not required.

B. Regulatory Requirements: UL listed motor, controls and equipment.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

C. Mock-Up: Provide a mock-up for evaluation of fabrication and application workmanship.

1. Preview display available at Porvene.

2. Do not proceed with remaining work until workmanship is approved by Architect.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

1.7 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

A. Contractor has responsibility for an extended Corrective Period for work of this Section for the period stated from date of Substantial Completion against all the conditions indicated below, and when notified in writing from Owner.

** NOTE TO SPECIFIER ** Series 200 and 300 coiling doors only.

1. 15 months (Series 200, 300).

** NOTE TO SPECIFIER ** Series 400, 500, 600 coiling doors only.

2. 24 months (Series 400, 500, 600).

B. Contractor shall promptly and without inconvenience and cost to Owner correct said deficiencies through installing dealer.

1. Failure due to defective materials and workmanship.

2. Failure due to design or installation performance to resist wind loading.

C. Manufacturer shall be notified immediately of defective products, and be given a reasonable opportunity to inspect the goods prior to return. Manufacturer will not assume responsibility, or compensation, for unauthorized repairs or labor.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Porvene Doors, Inc., which is located at: 14241 Grant St.; Moreno Valley, CA 92553; Tel: 877-906-3999; Fax: 877-343-6677; Email: request info (); Web: www.porvenedoors.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

B. Substitutions: Not permitted.

** NOTE TO SPECIFIER ** Delete INDUSTRIAL COILING DOORS if not required.

2.2 INDUSTRIAL COILING DOORS

** NOTE TO SPECIFIER ** Delete options and features not required.

A. Series 200 Continuous Sheet Door as manufactured by Porvene Doors, Inc.

1. Sheet construction: 26 gauge galvanized steel roll formed in continuous corrugation.

** NOTE TO SPECIFIER ** Delete operation not required; chain or push-up is standard.

2. Operation: Hand chain operated or manual push-up depending on size.

3. Operation: Chain-Thru-Wall shall be chain hoist operated through the wall.

4. Operation: Motor operated.

** NOTE TO SPECIFIER ** Delete mounting not required. Interior face is standard.

5. Mounting: Interior face mounted on a prepared opening.

6. Mounting: Outside mount. Curtain can be assembled inside out for outside mounting.

** NOTE TO SPECIFIER ** Delete features not required.

7. Vision panel: 22 inches (559 mm) by 7-1/2 inches (191 mm) vision cutout through curtain covered by clear Lexan polycarbonate.

8. Vent: 14 inch (356 mm) by 6 inches (152 mm) vent hole through bottom of curtain covered by louvers and wire mesh.

9. Sloped bottom bar: Bottom bar shall conform to slope in finished floor.

10. Hoods: 24 gauge galvanized steel with baked epoxy primer and baked polyester topcoat to enclose coil.

** NOTE TO SPECIFIER ** Delete models not required.

B. Model 211 Commercial Sheet Door:

1. Hand chain operation or manual pushup depending on size.

2. "Nylofelt" sidestripping.

3. Wind load: Door construction designed to satisfy wind load of 10 psf (0.48kpa) or 63 mph (101 kph) up to 12 feet by 14 feet (3658mm x 4267mm).

C. Model 231 Industrial Sheet Door:

1. Hand chain operation.

2. "Nylofelt" or tempered steel and rubber depending on size.

3. Wind load: Door construction designed to satisfy wind load of 15 psf (0.72 kpa) or 77.5 mph (124.7 kph) up to 14 feet by 18 feet (4267 mm by 5486 mm).

** NOTE TO SPECIFIER ** Delete door feature if not required.

4. Wicket door.

D. Model 232 Insulated:

1. Rating: Overall thermal efficiency rating of R = 5.24 (U = 0.191).

2. Cast reduction gear chain operation.

3. Side strip, top draft stop, and factory installed side draft stop combination.

4. Wind load: Door construction designed to satisfy wind load of 15 psf (0.72 kpa ) or 77.5 mph (124.7 kph) up to 14 feet by 16 feet (4267 mm by 4877 mm).

E. Model 233 Wind-Lock:

1. Cast reduction gear chain operation.

2. Tempered steel banding and rubber side strip.

3. Wind load: Door construction designed to satisfy a non-operational wind load up to 60 psf (2.87kpa) or 155 mph (249.4 kph) up to 12 feet by 18 feet (3658 mm by 5486 mm).

F. Model 234 Insulated Wind-Lock:

1. Overall thermal efficiency rating of R = 5.24 (U = 0.191).

2. Cast reduction gear chain operation.

3. Side strip, top draft stop, and factory installed side draft stop combination.

4. Wind load: Door construction designed to satisfy a non-operational wind load up to 60 psf (2.87 kpa) or 155 mph (249.4 kph) up to 12 feet by 16 feet (3658 mm by 4878 mm).

G. Model 278 Wicket Door:

1. Wicket for sheet doors.

2. Used with Series 200 sheet doors.

3. Interior face mounted on a prepared opening.

H. Model 291 Mini / Self Storage:

1. Push-up only.

2. PVC side strip seal.

3. Wind load: N/A.

4. Torque tube: Formed with 30 gauge galvanized steel sheet rolled around and attached to stamped galvanized steel drums to resist deflection to 0.03 inch per foot (2.5 mm/m) of door width.

5. Support brackets of 18 gauge galvanized steel.

6. Curtain mini-lock: 5/16 inch (8 mm) round steel slide bolts attached to curtain suitable for padlocking. Padlock not provided.

7. Guides: Roll-formed 18 gauge galvanized steel channels.

I. Materials:

1. Steel sheet: 26 gauge ASTM A653.

** NOTE TO SPECIFIER ** 232 series and 234 series only. Delete if not required.

2. Insulation: shall be Aluminum foil Polyethylene bubble insulation with wear-resistant Polyester treatment, laminated to corrugated sheet.

J. Fabrication:

** NOTE TO SPECIFIER ** 211, and 291 series only. Delete if not required.

1. Bottom bar: Curtain shall be reinforced with a bottom bar consisting of a continuous 13 gauge galvanized roll-formed sheet steel angle with E.P.D.M. blade astragal.

** NOTE TO SPECIFIER ** 231, 232, 233 and 234 series only. Delete if not required.

2. Bottom bar: Curtain shall be reinforced with a bottom bar consisting of a 2 inches by 2 inches by 3/16 inch (51 mm by 51 mm by 5 mm) structural steel angle with E.P.D.M. astragal.

** NOTE TO SPECIFIER ** 291 only. Delete if not required.

3. Side stripping: P.V.C. shall be attached to curtain edges.

** NOTE TO SPECIFIER ** 231 series only. Delete if not required.

4. Side stripping: P.V.C. and "Nylofelt" shall be attached to curtain edges for doors under 14 feet (4267mm) wide. Doors 14 feet (4267mm) wide and over provided with tempered steel and rubber side stripping. Side stripping shall be attached to curtain edges.

** NOTE TO SPECIFIER ** 232, 233 and 234 series only. Delete if not required.

5. Side stripping: Tempered steel and P.V.C. side stripping. Side stripping shall be attached to curtain edges.