BuyitNowfor the "full version"£50.00 inc P&P!
Technical DataCD2 includes all ofthe following below plus much more!
80 Makers plus14,000 Modelsfrom 1965 to 2004 upwards
Cars, light commercial vehicles, medium weight trucks and tractors.
Vehicle identification
o Engine capacity
o Engine power
o Fuel type
o Illustrations showing VIN plate/Engine code location
o Data link connector (DLC) location
o Rim/Tyre sizes and tyre pressures
o Service illustrations
Tuning and emissions
o Illustrated firing order and Preparatory conditions
o Basic ignition adjustment
o Engine oil temperature
o Idle speed
o Emission levels
Service adjustments
o Spark plug type and plug gap
o Valve clearance
o Cylinder compression
o Oil pressure
Lubricants and capacities
o Specification and capacities of engine oil, transmission oil anddifferential oil
o Capacities of engine cooling system
Ignition system
o Ignition type and ignition system
o Ignition coil and distributorspecifications
o Setting data
Fuel system
o Description of injection systems including Manufacturer, Systemand Type
o Technical data covering:-
- system and regulated pressures
- engine coolant temperature (ECT) sensor
- engine speed (RPM) sensor
- injectors
- oxygen sensor heater
Tightening torques
o Cylinder head
o Main bearing and big-end bearing
o Oil sump and oil pump
o Clutch
o Camshaft sprocket and crankshaft pulley
o Wheel hub and brakes
o Wheel nuts and bolts
Brake discs and brake drums
o Minimum component dimensions (permissible wear limits)
Air conditioning
o Refrigerant and Refrigerant oil (type andquantity)
Repair times
o Mechanical repairs
o Electrical repairs
o Bodywork repairs
o Air conditioning
o Manufacturer time allowance given in decimal hours
o Quick and easy labour charge quotes
o Estimates can be printed and saved
o Spare part charge can be added
o Additional tasks can be added
o Hourly rate can be customized
Wheel alignment
o Wheel alignment data
o Setting instructions
o Service illustrations
o Tightening torques
o Rim and tyre specifications
o Tire pressures and load condition
o Terminology
Valve timing // Timing belts
o Removal and installation procedures
o Replacement Interval Guide
o Repair Times
o List of special tools required
o Illustrated timing belt routing andtiming marks
o Tightening torques
o Illustrated serpentine belt routing
Timing chains
o Removal and installation procedures
o Required special tools
o Repair Times
o Illustrated timing chain routing and timing marks
o Tightening torques
o Illustrated serpentine belt routing
Timing gears
o Required special tools
o Illustrated timing gear locations and timing marks
o Tightening torque
o Illustrated serpentine belt routing
Service schedules
o Service schedules in line withmanufacturer´s original schedules
o Service intervals based on:
- mileage
- Inspection I, II or III
- elapsed time
o Mechanic´s service tick list
o Listing of required spare parts
o Service illustrations showing:
- Drain and refill locations
- Serpentine belt routing
- Jacking points
- Pollen filter locations
o Merging feature to enable adding of service times into the
repair times summary for quoting and billingpurposes
Service interval indicatorand key programming
o Service indicator resettinginstructions
o Key programming for:-
- anti-theft alarm system
- central locking
- immobilizer
Accessing trouble codes
o Data link connector (DLC) location(s)
o Procedure for accessing trouble codes
o Flash code interpretation
o List of probable fault causes (Primary fault location and associated fault(s))
o Quick reference link to fault code list
Engine management system
o Positive identification of enginemanagement systems
o System and component tests based on technical test data
illustrated by the related test procedure
o Quick reference link to the circuitdiagram associated with
the selected component
o Quick reference link to engine bay illustration showing location
and description of the selectedcomponent
o Schematic diagram of ECM harness multi-plug pin locations
o Schematic system layout
o General test procedures
o Description of component operation
o General safety precautions
Engine management Pin data
o Checking input signals (from sensors and components) to ECM
o Schematic diagram of ECM harness multi-plug pin locations viewed
from terminal side and from wire side
o View mode by:-
- component name
- pin number
- component and pin numbers
o Dynamic testing of enginecomponent signals based on test data
o Oscilloscope wave forms
o Screen tip feature enablesvisualization of ECM harnessmulti-plug pin description
o Selected component/ECM harness multi-plug pin highlighted by colour
Trouble shooter
o Fault description on engine management systems
o Quick reference link to component check sequence
o Flow chart presentation of component check sequence
o Quick reference link to component related engine management
test data by clicking on the selected component
Airbags
o System description
o Arming/Disarming procedure
o Steering wheel removal andinstallation
o Tightening torques of SRS-related components
o Self diagnosis and fault code description
Air conditioning
o System description
o System pressure
o Self diagnosis and fault codedescription
o Technical specification such as:-
- refrigerant quantities
- temperature related sensor resistance
o Compressor clutch clearance
o Quick reference link to circuit diagram
o AC control module harness multi-plug pin layout
o Component location - engine bay
o Component location - instrument panel
ABS
o System and component tests based on technical
data and illustrations
o Quick reference link to the selected component
o Self diagnosis and fault codedescription
o ABS control module harnessmulti-plug pin layout
o Component location - engine bay
o Component location - passenger compartment
Component locations
o Quick reference link to the following vehicle systems:-
- engine management system
- air conditioning
- ABS
- airbags
- fuse boxes and relay plates
Circuit diagrams:
o Quick reference link to the following vehicle systems:-
- engine management system
- air conditioning
- ABS
o Circuit diagrams feature quick reference link to the selected component
o Control module harness multi-plug pin layout
o Screen tip feature enables visualization of component
description in the citcuit diagram window
o Zoom feature for circuit diagram enhancement
Means that you only print of what you need to know.
Easy to search through.Plus even if you change your car or vehicle? It willstill becovered by this CD!
Terms & Conditions
This is a full version"COPY" of the original Autodata cd2 rrp £470.00!!!
Sadly we do not accept Returns for obvious reasons as this is computersoftware.
All CD's are checked before dispatch and will also come with fullinstructions on how to load on to your computer
WINDOWS 98 / 2000 / MEcompatable!
(CAUTION! "VISTA" may not allow this cd to work)