SYSTEM DESIGN INFORMATION
Client ………………………………………………………………………………………………
Address …………………………………………………………………………………………
Telephone ………………………………………………………………………………………
Fax ………………………………………………………………………………………………
e-mail ……………………………………………………………………………………………
Others notes ……………………………………………………………………………………..
Required Product Flow Rate (m3/h or GPD): ……………………………………………………………..
Expected recovery: ………………………………………………………………………………………..
Water temperature on site summer °C: ………………………………………………………….
winter °C: ………………………………………………………….
design °C: ………………………………………………………….
R.O. - plant indoors outdoors
Designed for continuous use: yes no
If not, please state needed peak hourly capacity:
______
Plant will be operated by: - Enduser yes no
- Trained personnel yes no
- Equipment manufacturer yes no
- Others yes no
Water source: Well water Softened water
Surface water Filtered effluent water
Sea water Others
Existing Pre-treatment yes no SDI …………………………..…………….
List of pre-treatments steps: ………………………………….………………………….…………...…….…
……………………………………….………………………………………………..….…………….…….
Planned pre-treatment: ……………….…………………………………………….…..………………..……
……………………………………………………………………………………….……………………….
Bacterial control: yes no Dechlorination - AC filter
Chlorine used: yes no - Na bisulfite
Chloramines used: yes no - Other
Desired acidification: HCI
H2SO4
None
Brief description of other pre-treatment steps: …………………………………..………………………..
(e.g clarification, flocculation, multimedia/sand filtration etc):……………….…………………………..
……………………………………………………………………………………………………….…….
Application: Potable water
Industrial supply for:
Boiler feed Pharma
Electronics Other
Specify water quality needed after RO treatment: ……………………………………………………….
…………………………………………………………………………………………………………….
State other desired design criteria: ……………………………………………………………………….
…………………………………………………………………………………………………………….
Client.. ………………………………………………………………………………………………
WATER ANALYSIS
Water Identification: …………………………………………………………………………………………………..
Feed source: …………………………………………………………………………………………………………..
Conductivity:…………………………… pH: ………………….. Temperature (°C): …………………………..
Feed water analysis 1: NHA4+ : …………… CO2 : …………………
K+: …………… CO3 : …………………
Na+: …………… HCO3 : …………………
Mg++: …………… NO3 : …………………
Ca++: …………… CI- : …………………
Ba++: …………… F- : …………………
Sr++: …………… SO4-- : …………………
Fe++: …………… PO4 : …………………
Fe (tot): …………… SiO2 (colloidal) : …………………
Mn++: …………… SiO2 (soluble) : …………………
H2S :………………
Other ions: ……………………………………………………………………………………………………………..
TDS (by method): ……………………………………………………………………………………………………..
TOC: ……………………………………………………………………………………………………………………
TSS: ……………………………………………………………………………………………………………………
BOD: ……………………………………………………………………………………………………………………
COD: ……………………………………………………………………………………………………………………
Total alkalinity (m-value): ……………………………………………………………………………………………
Carbonate alkalinity (p-value): ………………………………………………………………………………………
Total hardness: ……………………………………………………………………………………………………….
Turbidity (NTU): ………………………………………………………………………………………………………
Silt density index (SDI): ……………………………………………………………………………………………..
Bacteria (count/ml): …………………………………………………………………………………………………
Free chlorine: ………………………………………………………………………..……………………………….
Remarks: ………………………………………………………………………………………………………………
(odour, smell, colour, biological activity, etc.): ……..…….……………………………………………………….
………………………………………………………………………………………………………………………….
Analysis by: …………………………………………………………………………………………………………….
Date: …………………………………………………………………………………………………………………….
1 Please give units (mg/l as ion or ppm as CaCo3 or mcq/l).
SYSTEM DESIGN INFORMATION CHECK – FILLED BY
Name – Position ______
Date: ______Signature______
B/P403-01-02(EN)