Model DO700 DO Meter
Operation Manual
Table of Contents
1. Brief Introduction ------
2. Technical Parameters ------
2.1. pH ------
2.2. mV ------
2.3. Conductivity ------
2.4. Dissolved Oxygen ------
2.5. Other Technical Parameters ------
2.6. Working Condition ------
3. Instructions to the Meter ------
3.1. LCD Display ------
3.2. Operation Keys ------
3.3. The Storage, Recall and Elimination of the Measuring Information ------
4. pH Measurement ------
4.1. Preparation Work ------
4.2. Meter Calibration ------
4.3. Sample Test ------
4.4. Parameter Setting ------
4.5. Considerations ------
4.6. The Self-diagnose Information ------
5. mV Measurement ------
5.1. Sample Test ------
5.2. Parameter Setting ------
6. Conductivity Measurement ------
6.1. Preparation Work ------
6.2. Meter Calibration ------
6.3. Sample Test ------
6.4. Important Statement ------
6.5. Parameter Setting ------
6.6. Considerations ------
7. DO Measurement ------
7.1. Preparation Work ------
7.2. Meter Calibration ------
7.3. Water Sample Test ------
7.4. Considerations ------
7.5. Parameter Setting ------
7.6. Change the Membrane Cap ------
7.7. Zero Oxygen Calibration ------
7.8. Salinity Calibration ------
7.9. Barometric Pressure Setting ------
8. Meter’s Complete Kit ------
9. Warranty ------
ChartⅠ Meter Parameter Setting Schedule
ChartⅡ Meter Restore to Producer Setting Schedule
Chart Ⅲ Code Icon and Abbreviation Schedule
Chart Ⅳ Content of Saturated Oxygen in Water at Different Temperature
Chart V Content of Saturated Oxygen at Different Barometric Pressure
ChartⅥ Content of Oxygen at Different Altitude
1. Brief Instruction:
Thanks for buying and using the model DO700 DO Meter (the following called “meter” in short).
Before using this meter, please read the operation manual carefully in order to help use and maintain it correctly. On the basis of improving instrument of performance constantly, we reserve the right of changing the content of this manual and accessories in case of not notifying in advance.
This meter is a perfect combination with the most advanced electronic technology, sensor technology and software design. The meter can measure the parameters of pH, mV, conductivity, TDS, salinity, resistivity, DO and temperature for high accuracy water solution. It is the best portable water analysis meter with the highest performance and the lowest cost. It is suitable for the trade such as the mining industry, power plant, water treatment projects and environmental protection, etc., especially has more extensive application in the field and spot test.
Built-in microprocessor chip, beautiful appearance, multi-functional and easy to use, this meter has the following prominent features:
1.1. 1.1 Multi-parameter meter, equipped with pH electrode, conductivity electrode and DO electrode, calibration solution and special carrying case, easy to use.
1.2. Built-in microprocessor chip. Its features up to automatic calibration, automatic temperature compensation, data storage, auto power off, low voltage indication, function setting and automatic self-diagnose etc.
1.3. Adopts digital filter and step slipping technology to intelligently improve meter’s response speed and result accuracy. “ ” will appear when reading to be stable.
1.4. Automatically recognize 13 kinds of pH standard buffer solution. User can choose anyone from three series of buffer solutions: Europe & U.S.A. series, NIST series and China series.
1.5. High purified water and ammonia added purified water pH measuring mode can be set up, for this two special pH measuring modes, besides the general slope temperature compensation, also added function of nonlinearity solution temperature compensation to make measurement more accurate, especially suitable for the fields of electric power and petrochemical etc.
1.6. Adopts advanced automatic frequency convertible and voltage regulation technology to enlarge the measuring range of conductivity electrode which constant K=1 to 10 times. It can meet measuring accuracy requirement for range within 0 to 100mS/cm by using only one-point calibration. It is the particular one–point calibration function for this meter.
1.7. Automatically recognize 8 kinds of conductivity standard solution. User can choose anyone from two series of standard solutions: Europe & USA series and CHINA series.
1.8. Automatic select conductivity measuring range, the meter will do non-linearity temperature compensation test for purified and high purified water less than 10uS/cm, which greatly improve the measuring accuracy. It is especially suitable for use in fields of electric power, microelectronics and medicine.
1.9. Equips new type of DO electrode with temperature and salinity sensor which has function of automatic temperature compensation and automatic salinity compensation as well as manual barometric pressure compensation inside meter, easy to use, accurate to measure.
1.10. Polarogram type DO electrode has special electrode calibration cap. Only needs 3 to 5 minutes for electrode polarization. Electrode adopts combination diaphragm cap which very convenient to use. Each DO electrode equips with three spare diaphragms caps.
1.11. Meter’s circuit board adopts SMT film-covering technology to improve meter’s production reliability.
1.12. Meter has the back light LCD display monitor.
1.13. Dustproof and waterproof meter meets IP57 rating.
2. Technical Parameters:
2.1. pH:
Measuring range / (-2.00 to 19.99) pHResolution / 0.1/0.01 pH
Accuracy / Meter: ±0.01pH; Connect meter with electrode: ±0.02pH
Input current / ≤2×10-12 A
Input impedance / ≥1×1012 Ω
Stability / ±0.01 pH/3h
Temp. compensation range
/ (0 to 100) ℃ (automatic)2.2. mV:
Measuring range / -1999 mV to 0 to 1999mVResolution / 1mV
Accuracy / ±0.1% FS
2.3. Conductivity
Measuring range
/ Conductivity:(0.00 to 19.99)μS/cm (20.0 to 199.9)μS/cm
(200 to 1999)μS/cm (2.00 to 19.99) mS/cm
(20.0 to 199.9) mS/cm
TDS: (0 to 100) g/L
Salinity: (0 to 100) ppt
Resistivity:(0 to 100) MΩ·cm
Resolution / 0.01/0.1/1μS/cm 0.01/0.1 mS/cm
Accuracy
/ Meter: ±1.0% FS, connect meter with electrode:±1.5% FSTemp. compensation range / (0 to 50) ℃ (automatic)
Electrode constant / 0.1 / 1 / 10 cm-1
Benchmark temperature / 25℃, 20℃and 18℃
2.4. Dissolved Oxygen:
Measuring range / (0 to 40.00) mg/L(ppm) (0 to 200.0) %Resolution / 0.1/0.01 mg/L (ppm) 1/0.1%
Accuracy / Meter: ±0.10 mg/L, connect meter with electrode: ±0.40 mg/L
Response time / ≤30 s (25℃, 90% response)
Residual current
/ ≤0.1 mg/LTemp. compensation range
/ (0 to 45) ℃ (automatic)Salinity compensation range
/ (0 to 45) ppt (automatic)Barometric pressure compensation range / (66 to 200) kPa (manual)
Automatic calibration / Air saturated by water; water saturated by air
Electrode type / Polarogram type
2.5. Other Technical Parameters:
Data storage / 400 groupsStorage content
/ Series number, measuring value measuring unit and temperature,Power / Two AA batteries (1.5V x2)
Size and weight / Meter: (65 x 120 x 31)mm/180g; carrying case: (360 x 270x 76) mm/1.6kg
Quality and safety certification
/ ISO9001: 2000, CE and CMC2.6. Working Condition:
Environment temperature / 5 to 35 ℃ (0.01 grade)Environmental humidity / ≤85%
IP rating / IP57 Dustproof and waterproof
3. Instructions to the Meter:
3.1. LCD Display:
① —— Parameters mode icon
② —— Measuring value
③ —— Serial number and icon as measuring value to be stored and recalled, and indication icons for special states.
M+ — measuring value to be stored icon;
RM — reading to be recalled icon;
④ —— Measuring unit
⑤ —— Temperature measuring value and unit
⑥ —— Measuring value to be stable icon
⑦ —— Electrode calibration indicate icon
⑧ —— Indication icon of low voltage, appears when the voltage less than 2.4V, call attention to change the batteries.
3.2. Operation Keys:
The meter has 5 operation keys in all.
3.2.1. — Switch key
3.2.2. — Calibration key,.
(a) When in the measurement state, press this key to enter into calibration mode.
(b) When in the parameter setting state, press this key to change the number or the ON/OFF state.
3.2.3. — Function key
(a) Short-time press (time<1.5s) switch the measuring parameters, the meter will display
→ → (conductivity)→ (dissolved oxygen);
(b) Depress (time >2s) to enter into the parameter setting mode P1, and again short-time press, will in turn display P2, P3…
3.2.4. — Back light and entrance key
(a) When in the measuring state, short press (less than 1.5s) to open or close the back light display;
(b) When in the calibration state or the parameter setting state, press this key to confirm, and then the meter enters into measuring state;
(c) When in mode, long press the key to change pH resolution: 0.01→0.1 pH; and then release;
(d) When in mode, long press the key to in turn change parameter mode:
(total dissolved solid)→ (salinity) → (resistivity)→ (conductivity), and then release the key.
(e) When in mode, long press the key to in turn change unit symbol: mg/L→ppm→%, and then release the key.
3.2.5. — The combination key of memory and recall
(a) Short time press (press time less than 1.5s) to save the measuring data, long time press (＞2s) to recall the saved measuring data when in the measurement state.
(b) When in the parameter setting state, press to alter the number or ON/OFF state.
3.3. The Storage, Recall and Elimination of the Measuring Information:
3.3.1. Store the measuring information:
In the measuring mode, when the measuring data is stable and appear the “ ”, short-time press key(＜1.5s), LCD will display “ M+ ” icon and storage serial number, and meanwhile memory all the measuring information. Meter can separately store 100 groups of measuring information in the mode of pH, mV, conductivity and dissolved oxygen, can totally store 400 groups.
3.3.2. Recall measuring information:
(a) Under the measuring mode, depress the key, meter will recall the last stored information, and the storage number and “RM” icon will appear in the lower right corner of the LCD, and the complete measuring information. Again press or
key, meter will in turn recall all the measuring information, depress or
key can quickly query;
(b) In the recalling mode (there are “ RM ” and storage serial number in the upper right corner of the LCD), press key to return to the measuring mode.
3.3.3. Eliminate the stored measuring information:
In the recalling mode, depress the key for 5 seconds, LCD will appear “ ” for 2 seconds. It means the storage has been eliminated, and returns to measuring mode.
4. pH Measurement:
4.1. Preparation Work:
4.1.1. Press key to turn on. Short press key to switch to mode.
4.1.2. Install the model 201T-S pH/ATC 3-in-1 combination pH electrode into meter’s socket.
4.2. Meter Calibration:
4.2.1. Press to enter into calibration mode, LCD displays the twinkling “ ” indicate to enter into the first point calibration.
4.2.2. Wash the pH electrode in purified water and dry it, then immerge it into the pH7.00 buffer solution, rock the electrode holder and then still, waiting for the data stable and appear “ ”, then again press key , the LCD will appear a twinkling 7.00 pH, calibration finishes after several seconds and appear a stable pH value and a twinkling “ ”, indicates the first point calibration has been finished and enters into the second point calibration.
4.2.3. Wash the pH electrode in purified water and dry it, then immerge it into the pH4.00 buffer solution, rock the electrode holder and then still, waiting for a stable data and appear “ ”, then again press key , the LCD will appear a twinkling 4.00pH, calibration finishes after several seconds, LCD will appear a stable pH value and a twinkling “ ”, indicates the second point calibration has been finished and enters into the third point calibration.
4.2.4. Wash the pH electrode in purified water and dry it, then immerge it into the pH10.01 buffer solution, rock the electrode holder and still, waiting “ ” for the data stable and appear, then again press key , LCD will appear a twinkling 10.01 pH, calibration finishes after several seconds, appear a stable pH value and “ ” three calibration indication icon, see picture (4-1), indicates the three-point calibration has been finished and entered into measuring mode.
4.2.5. Note:
(a) This meter can adopt random one-point, two-point or three-point automatic calibration, after the first point calibration (see item 4.2.2.), press to confirm one-point calibration and enters into measuring mode. The indication icon “ ” for one-point calibration will appear on the lower left corner of LCD. When the measuring accuracy is ≤±0.1pH, user just need to choose one kind buffer solution to take one-point calibration according to the measuring range.
(b) After the second point calibration, (see item 4.2.3.), press to confirm two-point calibration and enter into measuring mode. The indication icon “ ” for tow-point calibration will appear on the lower left corner of LCD. User can choose pH4.00 and pH7.00 to calibrate if the measurement is just within the acidity range and choose pH7.00 and pH10.01 to calibrate if just within the alkalinity range.
(c) User should choose three-point calibration so as to reach a more accurate measurement if the measuring range is wide, or if the electrode has been used for long or has ageing phenomenon. As to the new electrode which be used for the first time, it must be calibrated by three-point calibration to keep the unanimity of the meter slope adjustment with the pH electrode.
4.3. Sample Test:
Immerge pH electrode into the sample solution after washing and dry it, rock the electrode holder and still, when the LCD appears the icon “ ” to take the reading after displaying value to be stable.
Note: According to the pH equal temperature measuring theory: the closer the temperature of the sample solution with the calibration solution, the more accurate the measuring value will be acquired. So please comply with this theory.
4.4. Parameter Setting:
4.4.1. pH measuring parameter setting schedule (Chart (4-1))
Chart (4-1)
Prompt Mark / Parameter Setting Items / Code /Parameters
P1 / pH buffer solution series selection / / USA (Europe & U.S.A series)NIS (NIST series)
CH (China series)
P2 / Purified water pH temperature compensation setting / / OFF-On (shut-set)
P3 / Ammonia added purified water pH temperature compensation setting / / OFF-On (shut-set)
P4 /
Temperature unit setting
/ ℃ ℉P5 / Back light display time setting / / 0-1-3-6min
P6 / Auto power off setting / / 0-10-20min
P7 / Restore to producer setting / OFF-On ( shut-set)
4.4.2. pH buffer solution series selection (P1)