2016 Post #6 BIO PAK 240 R Written Test

Contestants Name: ______Team Name: ______

  1. Prior to using the BioPak 240 Revolution it must be determined that the user is ______fit.

physicallymentallymedically

  1. Do not open the cylinder valve in the presence of open flame, ______or high radiant heat.

sparksoillow

3.The use of an SCBA will add to the workload and stress of the ______.

weareruserperson

4.A foreign _____ may cause cylinder corrosion.

bodygasobject

5.DOT requires carbon fiber wrapped aluminum cylinders be tested by an approved facility on a __-year cycle from the date of manufacture.

2105

6.The fiber optic cable may only be ______to the BioPak 240R remote gauge assembly.

attachedconnectedassembled

7.______after completion of BioPak use, remove the used CO2 scrubber canisters.

soon shortlyimmediately

8.Use only ______and disinfectants that are approved by Bio marine.

cleanerscleanserssoaps

9.Remove the oxygen cylinder making sure the seal ______remains in place and install the regulator cover.

gasketo-ringwasher

10.C.O.P.D. could limit or ______the use of the BioPak 240 Revolution.

prohibit limitprevent

11.The manual(s) are the ______recommended procedures for maintaining the BioPak 240R.

maximumminimumspecific

12.To ______mold growth remove the moisture control foam pads after each use.

limitprevent prohibit

13.Pre-packing the BioPak 240 R with carbon dioxide scrubbers is only permitted when utilizing ______carbon dioxide scrubber.

factoryrefillableOrbsorb

14.Pre-packed carbon dioxide scrubbers may only be stored in the ______for a maximum period of 1-year.

containersapparatusboxes

15.Users are not permitted to mix ______of the Orbsorb within a BioPak.

versionscontainerstypes

16.The oxygen cylinder must be fully charged to above _____ psi to perform a high pressure leak test.

260030001500

17.The Cylinder should be ______regularly for signs of damage to the outer wrapping.

checked inspected tested

18.Never pry an O-ring from its glands with a ______. Remove O-rings by hand or with the pick tool provided in the service kit.

wrenchscrewdriverpry-bar

19.Cristo-Lube and Dow-111 are the only ______approved for use in the apparatus.

lubricantschemicalspastes

20.The Alarm module will require ______if any damage to the housing is discovered.

servicingattentionreplacement

Identification of Parts

21.Item # 3 of the upper housing assembly drawing

green knoboxygen knob external oxygen knob

22.Item # 7 of the upper housing drawing

spacer barvent spacervent valve spacer

23. Item #12 of the upper housing drawing

foam padvibration padlatch foam pad

24. Item # 18 of the upper housing drawing

Hold down straphold down gripcarrying handle

25. Item # 1 of the Pneumatic Assembly

supply lineoxygen supply linebypass feed tube

26.Item # 2 of the Pneumatic Assembly

bypass linebypass return tubesupply line

27.Item # 6 of the Pneumatic Assembly

bypass valve buttonbypass valve push button bypass valve

28.Item # 9 of the Pneumatic Assembly

Oxygen regulator assemblyregulator assemblyregulator

29. Item # 3 of the Center Section Lid Assembly

scrubber holderscrubber braceflow baffle

30. Item #4 of the Center Section Lid Assembly

Metal screwself-tapping screwsstainless screw

2016 BIO PAK 240 R Written Test Answers

  1. medically17. inspected
  1. sparks18. screwdriver
  1. user19. lubricants
  1. Gas20. replacement
  1. 5
  1. connected
  1. immediately
  1. cleaners
  1. washer
  1. prevent
  1. minimum
  1. prevent
  1. Orbsorb
  1. apparatus
  1. versions
  1. 1500

2016 BIO PAK 240 R Identification of Parts Answers

21.external oxygen knob

22.vent spacer

23. latch foam pad

24.carrying handle

25. bypass feed tube

26. bypass return tube

27.bypass valve push button

28. oxygen regulator assembly

29. flow baffle

30.self-tapping screws

1