DynaGlass™ FRP Ceiling / Wall Panels Specification
PART 1 - GENERAL
1.01 Scope
Provide DynaGlass (Wall)(Ceiling) Panels.
1.02 Related Sections
A. Section 07 20 00 – Thermal Protection
B. Section 08 11 00 – Metal Doors and Frames
C. Section 08 70 00 – Hardware
D. Section 09 22 26 – Suspension Systems
E. Section 09 51 00 – Acoustical Ceilings
F. Section 09 90 00 – Painting and Coating
G. Section 09 72 00 – Wall Coverings
H. Section 10 22 00 – Partitions
1.03 References
A. American Society for Testing and Materials (ASTM)
1. ASTM D-3841-97 - Sanitary Wall & Ceilings.
2. ASTM D-790 – Flexural Strength/Modulus.
3. ASTM D-638 – Tensile Strength/Modulus.
4. ASTM D-570 – Water Absorption.
5. ASTM D-256 – Izod Impact Strength.
6. ASTM D-696 – Coefficient of Linear Thermal Expansion.
7. ASTM D-2583 – Barcol Hardness.
8. ASTM D-792 – Specific Gravity.
9. ASTM 1929 – Self-Ignition Temperature.
10. ASTM E-84 – Flame Spread / Smoke Generation.
B. Factory Mutual, Reports J.I.3005041 & J.I.3001891.
C. USDA Approval.
D. ICBO Approval.
E. Agriculture Canada.
1.04 Submittals
A. Product data: Manufacturers standard data sheets listing dimensions and details.
B. Samples: Manufacturers standard samples including suspension, panels and colors.
C. Shop Drawings: Reflected ceiling plan and elevation drawings indicating ceiling layouts, dimensions and perimeter conditions.
1.05 Quality Assurance
A. Source limitations
1. FRP wall panels and moldings: Obtained from single source with resources to provide products of consistent quality in appearance and physical properties without delaying the work.
2. FRP ceiling panels: Obtained from single source with resources to provide products of consistent quality in appearance and physical properties without delaying the work.
3. (FRP)(Aluminum)(Stainless Steel)(Hot Dipped Galvanized Aluminum Cap) Suspension System: Obtained from single source with resources to provide products of consistent quality in appearance and physical properties without delaying the work.
1.06 Project Conditions
FRP Panels:
A. Deliver to site in manufacturer’s original unopened packages. All panels shall be inspected upon delivery in a well lit area, and defects reported.
B. Lay flat. Do not store on edge.
C. Store in a fully enclosed space.
D. Protect against damage from moisture, direct sunlight, surface contamination and other causes.
E. Acclimate to room conditions for at least 24 hours.
F. Handle carefully to avoid chipping edges of damaging units in any way.
PART 2 - PRODUCTS
2.01 Manufacturer
A. DynaGlassTM (Wall)(Ceiling) FRP Panels and Suspension by Chicago Metallic Corporation, 4849 S. AustinAvenue,Chicago,IL60638.Phone:800.323.7164or 708.563.4600.Web:chicagometallic.com/dynaglass.
2.02 Materials
A. Panels:
Finish: (Textured One Side)(Smooth Both Sides)
Color: (013 Bright White)(403 Ivory)(404 Silver)(405 Lite Grey)(406 Colonial)(410 Marble-wall pattern only).
Thickness: (.060)(.090)(.120) inches.
Wall Panel Size: (48) inches wide by (96) (108)(120)(144) inches long.
Ceiling Panel Size: 24 inches wide by (24)(48) inches long.
Fire Resistance: (Class “A”)
PART 3 - EXECUTION
3.01 Examination
A. Examine area receiving system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.
3.02 Installation
A. FRP Wall Panels: Installed in accordance with publications referenced below and Manufacturers’ written installation instructions.
B. FRP Ceiling Panels: Installed in accordance with Manufacturers’ written installation instructions and CISCA “Ceiling Systems Handbook”.
C. Subwall Surfaces: Clean, flat, dry, smooth and free of all dirt, dust and grease.
D. Wall Panels: Installed with 100% adhesive coverage (recommended method). [Fasteners are used in conjunction with adhesives in certain applications where needed (high moisture, uneven substrate, high abuse, large panels attached to ceilings)].
E. Expansion. Leave minimum 1/8 inch gap at ceiling and base. Allow 1/16 inch gap between panel and each side of division bar. If using face mounted molding (T-Bar, two-piece division bar, etc.), allow 1/8 inch gap between panels.
F. Fasteners:
1. Used to fasten panels to rough surfaces where adhesive would be inappropriate.
2. Non-corroding.
3. Fit snug but should not be overtightened.
Note: Refer to Manufacturer’s written installation instructions, including the use of silicone sealants.
Ceiling Systems and Specialty Products - USA and Canada: 800.323.7164 / Fax: 800.222.3744 / chicagometallic.com
chicago / baltimore / los angeles / belgium / denmark / the netherlands / uk / germany / france / hong kong / prc / malaysia / united arab emirates / mexico