PRODUCT SPECIFICATION GUIDE

MODEL: CONTROL DAMPERS

DIVISION 23 – HEATING, VENTILATION, AND AIR CONDITIONING (HVAC)(PREVIOUSLY DIVISION 15)

***************************************************************************************************************

Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) Format.

The section must be carefully reviewed and edited by the Engineer to meet the requirements of the project and local building code. Coordinate with other specification sections and the drawings.

Delete all "Specifier Notes" when editing this section.

***************************************************************************************************************

SECTION 233313 (Previously 15820)

CONTROL DAMPERS

PART 1 - GENERAL

1.1SECTION INCLUDES

  1. Galvanized steel round control dampers suitable for application in HVAC systems with velocities to 4,000 feet per minute (20.4m/s).

1.2SUMMARY

  1. Section 233100 – HVAC Ducts and Casings (Previously 15810).
  2. Section 230913.13 – Actuators and Operators (Previously 15900).

1.3REFERNECES

  1. AMCA 500-D – Laboratory Methods of Testing Dampers for Rating.

1.4SUBMITTALS

  1. Comply with requirements of Section 013300 - Submittal Procedures.
  2. Product Data: Submit manufacturer's product data.

1.Include leakage, pressure drop, and maximum pressure data.

2.Indicate materials, construction, dimensions, and installation details.

3.Include damper pressure drop data based on tests and procedures performed in accordance with AMCA 500-D.

1.5QUALITY ASSURANCE

  1. Dampers shall be warranted against manufacturing defects for a period of 5 years.
  2. Pressure Drop and Leakage ratings shall be based on tests and procedures performed in accordance with AMCA 500-D.

1.6DELIVERY, STORAGE, AND HANDLING

  1. Delivery: Deliver materials to site in manufacturer's original, unopened containers and packaging, with labels clearly indicating manufacturer, material, and location of installation.
  2. Storage: Store materials in a dry area indoor and protected from damage and in accordance with manufacturer’s instructions.
  3. Handling: Handle and lift dampers by sleeve or frame only. Do not lift damper by blades, actuator, or drive shaft. Protect materials and finishes during handling and installation to prevent damage.

PART 2 - PRODUCTS

2.1MANUFACTURER

  1. Pottorff, 5101 Blue Mound Road, Fort Worth, TX 76106. Phone (817) 509-2300

2.2CONTROL DAMPERS

  1. Model: CD-25R – galvanized steel round control damper.
  2. Ratings:

1.Temperature Ratings: -25°F to 180°F (-32°C to 83°C).

2.Leakage: Maximum 5.5 cfm/ft² @10.0 in. wg (0.028m³/s/m² @ 2.5 kPa).

3.Maximum Velocity: 4,000 fpm (20.4 m/s).

4.Differential Pressure Ratings: 10.0 in. wg (2.5 kPa).

  1. Construction:

1.Frame: 12” x 20 gauge minimum (305 x 1.0) galvanized steel.

2.Blades: 14gauge (2.0) equivalent galvanized steel – round.

3.Axles: 1/2” (13) diameter plated steel,mechanically attached to blade.

4.Bearings: Synthetic

5.Finish: [Mill galvanized] [stainless steel]

6.Control Shaft: ½” x 3” (13 x 76) drive axle.

7.Blade Seals: Polyethylene blade edge.

8.Mounting:

Vertical

Horizontal

2.3ACCESSORIES

  1. Actuator:

*****************************************************************************************************************Specifier Notes: Select one of the following and specify two-position or modulating and fail position.

*****************************************************************************************************************

1.Type:

Manual locking quadrant.

Electric 120 v, 60 Hz, two position, fail [open] [close].

Electric 24V, 60 HZ, [two position] [modulating], fail [open] [close].

Electric 230V 50/60 Hz, two position, fail [open] [close].

Pneumatic, 20 to 30 psi supply pressure, [two-position] [modulating], fail [open] [close].

2.Mounting:

Factory installed external.

  1. Stainless steel oilite bearings.

2.4SOURCE QUALITY CONTROL

  1. Factory Tests: Factory cycle damper [and actuator] assembly to assure proper operation.

PART 3 - EXECUTION

3.1EXAMINATION

  1. Examine areas to receive dampers. Notify the Engineer of conditions that would adversely affect installation or subsequent utilization of dampers. Do not proceed with installation until unsatisfactory conditions are corrected.

3.2INSTALLATION

  1. Install dampers at locations as indicated on the drawings and in accordance with manufacturer’s instructions.
  2. DO NOT compress or stretch damper sleeve or frame into the duct or opening.
  3. Handle dampers using the frame or sleeve. Do not lift or move damper using blades, drive shaft or actuator.
  4. Install connections to [electric, pneumatic] actuators as specified in section 15900.

END OF SECTION

Specification Guide for Control DampersNovember 2008

PottorffPage 1