Adjustable Pedestals for Terraces

SECTION 07 76 00

ADJUSTABLE PEDESTALS FOR TERRACES

Display hidden notes to specifier. (Don't know how? Click Here)

** NOTE TO SPECIFIER ** BUZON USA East; adjustable screwjack pedestals for terraces.
This section is based on the products of BUZON USA East, which is located at:
16 W. 56th St.
New York, NY 10019
Tel: 646-929-4318
Fax: 212-243-2868
Email:request info ()
Web:
[Click Here] for additional information.
We are proud to serve:
Alabama, Connecticut, Delaware, Florida, Georgia, Illinois, Indiana, Kentucky, Maine, Maryland, Massachusetts, Michigan, Mississippi, New Hampshire, New Jersey, New York, North Carolina, Ohio, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont, Virginia, West Virginia, Wisconsin.
Welcome to the Buzon family. For more than 25 years, Buzon pedestals have evolved alongside architects and contractors to create the most beautiful and intriguing spaces in the world. Buzon designed, developed, and manufactured the first pedestal and started selling them in the US in 1994.

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Adjustable pedestals for terraces.

1.2 RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete sections below not relevant to this project; add others as required.

1.2.1 Section 32 14 23 - Asphalt Unit Paving.

1.2.2 Section 04 22 23.29 - Split-Face Concrete Unit Masonry.

1.2.3 Section 04 40 00 - Stone Assemblies.

1.2.4 Section 06 15 00 - Wood Decking.

1.2.5 Section 06 50 00 - Structural Plastics.

1.2.6 Section 06 73 00 - Composite Decking.

1.2.7 Section 07 50 00 - Membrane Roofing.

1.2.8 Section 07 72 13 - Manufactured Curbs.

1.2.9 Section 07 76 13 - Roof Ballast Pavers.

1.2.10 Section 09 01 60.91 - Flooring Restoration.

1.3 REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

1.3.1 Belgium (CRIF) Centre De Recherches Scientifiques ET Techniques Del Industrie Des Fabrications: Test Report No. GT 7660/01.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data: Manufacturer's data sheets for each assembly specified, including but not limited to:

1.4.2.1 Performance characteristics.

1.4.2.2 Preparation instructions and recommendations.

1.4.2.3 Storage and handling requirements and recommendations.

1.4.2.4 Installation methods.

1.4.3 Method Statement: Prior to the installation of adjustable pedestal decking systems, Contractor shall submit an installation ' method statement' setting out the installation procedure for approval.

** NOTE TO SPECIFIER ** The contractor assumes the responsibility for and must take into consideration the structural capability and adequacy of the structure to carry the dead and live load weights involved, and that the density of any insulation is satisfactory to resist crushing and damaging the waterproofing membrane. Consult manufacturer and project engineer regarding: when spacer tab condition or design requires spacing between decking tiles or pavers other than standard spacing required by manufacturer; when considering use for in application other than a raised deck such as interior floors or stairs; when required pedestal height exceeds safe limits as determined by manufacturer; when pedestal load capacity exceeds maximum listed; when anticipating installation of items with excess weight on top of deck; when using Buzon pedestals on soil; when greater pedestal load capacity is required. Delete options for configuration and associated data not required.

1.4.4 Engineering Calculations:

1.4.4.1 Dead Load and Live Load Calculations: Indicating structure is designed to carry dead load and live load weights specific to application.

1.4.4.2 Density of Insulation: Sufficient to resist crushing and damaging waterproofing membrane.

1.4.5 Shop Drawings: Provide plans, elevations, sections, fabrication, installation, anchorage, interface of the work of this section with the work of adjacent trades and indicating dimensions, tolerances and finishes.

1.4.6 Verification Samples: For each finish product specified, two samples representing actual product assembly types specified.

1.5 QUALITY ASSURANCE

1.5.1 Single Source Requirements: To the greatest extent possible, provide pedestals and ancillary products specified in this section from a single manufacturer.

1.5.2 Manufacturer's Qualifications: Successfully engaged in the manufacture of adjustable pedestals for terraces for at least 10 years.

1.5.3 Installer Qualifications: Successfully engaged in installation of adjustable decking systems for at least 2 years; capable of estimating, building from working CAD details or plans, determining elevations and properly handling materials in pedestal decking assembly.

1.5.3.1 Method Statement Submission: Prior to the installation of the adjustable pedestal decking systems, the installer shall submit an installation ' method statement' setting out the installation procedure for approval.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

1.5.4 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

1.5.4.1 Finish areas designated by Architect.

1.5.4.2 Do not proceed with remaining work until workmanship is approved by Architect.

1.5.4.3 Rebuild mock-up area as required to produce acceptable work.

1.6 PRE-INSTALLATION MEETINGS

1.6.1 Conference: Convene a pre-installation conference to establish procedures to maintain optimum working conditions and to coordinate this work with related and adjacent work.

1.7 DELIVERY, STORAGE AND HANDLING

1.7.1 Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation. Pedestals are delivered boxed in cardboard cartons. These cartons should be stored in dry conditions and should not come into contact with rain or damp conditions. Protect from damage.

1.7.2 Handling: Handle materials to avoid damage.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.9 SEQUENCING

1.9.1 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.10 WARRANTY

1.10.1 Manufacturer's Warranty: Standard limited warranty against defects in materials and manufacturing.

1.10.1.1 Warranty Period for Deck Pedestals: Three years.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: BUZON USA East, which is located at: 16 W. 56th St.; New York, NY 10019; Tel: 646-929-4318; Fax: 212-243-2868; Email:request info (); Web:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 ADJUSTABLE DECK PEDESTALS

** NOTE TO SPECIFIER ** Delete if not required.

2.2.1 Basis of Design: Buzon DPH Series Screwjack Pedestals, as manufactured by Buzon.

** NOTE TO SPECIFIER ** Fill in blank below with custom material designation or delete line as applicable. Pedestals in polypropylene are not designed to support machines or equipment that may subject them to vibration. Custom options available such as transparent units for display or exhibition areas; contact manufacturer for details. Delete options for Pedestal Component Materials not required.

2.2.1.1 Pedestal Component Materials: Talc-loaded polypropylene copolymer with minimum 78 percent recycled CCP material, 20 percent Talc, 2 percent UV, Master Batch black, 100 percent recyclable. Temperature Range: Suitable for use from minus 22 to 250 degrees F (minus 30 to 120 degrees C).

2.2.1.2 Pedestal Component Materials: As scheduled and indicated on Drawings.

2.2.1.3 Pedestal Component Materials: ______.

2.2.1.4 Ancillary Application Materials:

2.2.1.4.1 Accommodates metal grid systems, fiberglass grid systems, timber-style decking, square-shaped or rectangular-shaped stone, concrete, natural stone, terrazzo, ceramic, composite pavers as approved by manufacturer.

2.2.1.4.2 Do not use Buzon Deck Supports over insulation less than 20 psi (134 kPa) or with low density polystyrene insulation.

2.2.1.5 Compliance:

** NOTE TO SPECIFIER ** Loading Test Positions: The following loading data for pedestals with loads applied at various positions on the load bearing top surface of the pedestals. 1/1 is load evenly applied across entirety of the load- bearing surface; 1/2 is load applied to half of the load- bearing surface; 1/4 is load applied to one quarter of the load-bearing surface. The tests were carried out on a universal testing machine, type Instron 1185 n degrees H - 4573, with a capacity of 22480 lbf (100 kN), fitted with a 22480 lbf (100 kN) force transducer No. 2518 - 201. The loading speed was 0.39 in (10 mm) per min. The mean RUPTURE value, expressed in daN or en lbf, is the result of carrying out the test on 3 supports at different heights. If any option other than ' Standard, talc-loaded...' is selected above for ' Pedestal Component Materials' then delete data listed under ' Configuration' for ' Loading Data.'

2.2.1.5.1 Testing Agency: Belgium (CRIF) Centre De Recherches Scientifiques ET Techniques Del Industrie Des Fabrications.

2.2.1.5.2 Test Method: Universal testing machine, Instron type.

2.2.1.5.3 Test Report: No. GT 7660/01.

2.2.1.5.4 Safety Factor for Pedestrian Terraces: Divide "Load Data" by 2 with an additional safety factor of 15 percent.

2.2.1.5.5 Safety Factor for Raised False Floors: Divide "Load Data" by 4 with an additional safety factor of 15 percent.

** NOTE TO SPECIFIER ** Adjusting ring is incorporated from model DPH-5 upwards; slope corrector is incorporated into pedestals from model DPH-4 upwards; slope corrector and numerous fixing accessories are available to support all types of structures, and can be used on all models from DPH-0 to DPH-3. Delete configurations not required.

2.2.1.6 Configuration: As scheduled and indicated on Drawings.

2.2.1.7 Configuration: DPH-0.

** NOTE TO SPECIFIER ** Delete options for nominal fixed height not required.

2.2.1.7.1 Nominal Fixed Height: As scheduled and indicated on Drawings.

2.2.1.7.2 Nominal Fixed Height: 11/16 in (17 mm).

2.2.1.7.3 Nominal Fixed Height: With PH5 slope corrector, 1-1/16 in (27 mm).

2.2.1.7.4 Base Diameter: 6-11/16 in (170 mm).

2.2.1.7.5 Base Surface Area: 35.185 sq in (227 sq cm).

2.2.1.7.6 Top Diameter: 5-45/64 in (145 mm).

2.2.1.7.7 Top Surface Area: 25.575 sq in (165 sq cm).

2.2.1.7.8 Top Diameter with PH5 Slope Corrector: 6-1/8 in (155 mm).

2.2.1.7.9 Top Surface Area with PH5 Slope Corrector: 29.14 sq in (188 sq cm).

2.2.1.7.10 Load Data: Mean value of load.

2.2.1.7.10.1 Position 1/1: 12349 lbf (5537 daN).

2.2.1.7.10.2 Position 1/2: 6556 lbf (2940 daN).

2.2.1.7.10.3 Position 1/4: 3267 lbf (1465 daN).

2.2.1.8 Configuration: DPH-1.

** NOTE TO SPECIFIER ** Delete options for nominal fixed height not required.

2.2.1.8.1 Nominal Fixed Height: As scheduled and indicated on Drawings.

2.2.1.8.2 Nominal Fixed Height: 1-1/8 in (28 mm).

2.2.1.8.3 Nominal Fixed Height: With PH5 slope corrector, 1-1/2 in (38 mm).

2.2.1.8.4 Base Diameter: 6-11/16 in (170 mm).

2.2.1.8.5 Base Surface Area: 35.18 sq in (227 sq cm).

2.2.1.8.6 Top Diameter: 5-45/64 in (145 mm).

2.2.1.8.7 Top Surface Area: 25.575 sq in (165 sq cm).

2.2.1.8.8 Top Diameter with PH5 Slope Corrector: 6-1/8 in (155 mm).

2.2.1.8.9 Top Surface Area with PH5 Slope Corrector: 29.14 sq in (188 sq cm).

2.2.1.8.10 Load Data: Mean value of load.

2.2.1.8.10.1 Position 1/1: 11652 lbf (5225 daN).

2.2.1.8.10.2 Position 1/2: 5374 lbf (2410 daN).

2.2.1.8.10.3 Position 1/4: 3038 lbf (1362 daN).

2.2.1.9 Configuration: DPH-02.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.9.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.9.2 Nominal Height Range: 1 to 1-27/64 in (25 to 36 mm).

2.2.1.9.3 Nominal Height Range: With PH5 slope corrector, 1-5/16 to 1-25/32 in (34 to 45 mm).

2.2.1.9.4 Top Diameter: 5-29/32 in (150 mm).

2.2.1.9.5 Top Surface Area: 27.435 sq in (177 sq cm).

2.2.1.9.6 Top Diameter with PH5 Slope Corrector: 6-1/8 in (155 mm).

2.2.1.9.7 Top Surface Area with PH5 Slope Corrector: 29.14 sq in (188 sq cm).

2.2.1.9.8 Base Diameter: 7-7/8 in (200 mm).

2.2.1.9.9 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.9.10 Load Data: Mean value of load.

2.2.1.9.10.1 Position 1/1 at 1-27/64 in (36 mm) Height: 2639 lbf (1183 daN).

2.2.1.9.10.2 Position 1/2 at 1-27/64 in (36 mm) Height: 1513 lbf (678 daN).

2.2.1.9.10.3 Position 1/4 at 1-27/64 in (36 mm) Height: 937 lbf (420 daN).

2.2.1.10 Configuration: DPH-2.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.10.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.10.2 Nominal Height Range: 1-3/8 to 2-3/32 in (35- to 53 mm).

2.2.1.10.3 Nominal Height Range: With PH5 slope corrector, 1-47/64 to 2-7/16 un (44 to 62 mm).

2.2.1.10.4 Top Diameter: 5-29/32 in (145 mm).

2.2.1.10.5 Top Surface Area: 27.44 sq in (165 sq cm).

2.2.1.10.6 Top Diameter with PH5 Slope Corrector: 6-1/8 in (155 mm).

2.2.1.10.7 Top Surface Area with PH5 Slope Corrector: 29.14 sq in (188 sq cm).

2.2.1.10.8 Base Diameter: 7-7/8 in (200 mm).

2.2.1.10.9 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.10.10 Load Data: Mean value of load.

2.2.1.10.10.1 Position 1/1 at 2-1/16 in (52.4 mm) Height: 3083 lbf (1382 daN).

2.2.1.10.10.2 Position 1/2 at 2-1/16 in (52.4 mm) Height: 1973 lbf (855 daN).

2.2.1.10.10.3 Position 1/4 at 2-1/16 in (52.4 mm) Height: 920 lbf (412 daN).

2.2.1.10.10.4 Position 1/4 at 1-27/64 in (36 mm) Height: 937 lbf (420 daN).

2.2.1.11 Configuration: DPH-2-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.11.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.11.2 Nominal Height Range: 1-47/64 to 2-1/4 (44 to 57 mm).

2.2.1.11.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.11.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.11.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.11.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.11.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.11.7.1 Position 1/1 at 2-1/4 in (57 mm) Height: 3436 lbf (1541 daN).

2.2.1.11.7.2 Position 1/2 at 2-1/4 in (57 mm) Height: 2716 lbf (976 daN).

2.2.1.11.7.3 Position 1/4 at 2-1/4 in (57 mm) Height: 1093 lbf (490 daN).

2.2.1.12 Configuration: DPH-3.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.12.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.12.2 Nominal Height Range: 1-15/16 to 6-1/16 in (50 to 78 mm).

2.2.1.12.3 Nominal Height Range: With PH5 slope corrector, 2-21/64 to 3-27/64 in (60 to 88 mm).

2.2.1.12.4 Top Diameter: 5-29/32 in (150 mm).

2.2.1.12.5 Top Surface Area: 27.435 sq in (177 sq cm).

2.2.1.12.6 Top Diameter with PH5 Slope Corrector: 6-1/8 in (155 mm).

2.2.1.12.7 Top Surface Area with PH5 Slope Corrector: 29.14 sq in (188 sq cm).

2.2.1.12.8 Base Diameter: 7-7/8 in (200 mm).

2.2.1.12.9 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.12.10 Load Data: Mean value of load.

2.2.1.12.10.1 Position 1/1 at 3-1/16 in (78 mm) Height: 2760 lbf (1237 daN).

2.2.1.12.10.2 Position 1/2 at 3-1/16 in (78 mm) Height: 1812 lbf (812 daN).

2.2.1.12.10.3 Position 1/4 at 3-1/16 in (78 mm) Height: 881 lbf (395 daN).

2.2.1.13 Configuration: DPH-3-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.13.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.13.2 Nominal Height Range: 2-11/64 to 3-7/64 in (55 to 79 mm).

2.2.1.13.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.13.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.13.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.13.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.13.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.13.7.1 Position 1/1 at 3-7/64 in (79 mm) Height: 328 lbf (1439 daN).

2.2.1.13.7.2 Position 1/2 at 3-7/64 in (79 mm) Height: 2168 lbf (972 daN).

2.2.1.13.7.3 Position 1/4 at 3-7/64 in (79 mm) Height: 1154 lbf (518 daN).

2.2.1.14 Configuration: DPH-4-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.14.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.14.2 Nominal Height Range: 3-5/64 to 4-5/16 in (78 to 110 mm).

2.2.1.14.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.14.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.14.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.14.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.14.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.14.7.1 Position 1/1 at 4-5/16 in (110 mm) Height: 3468 lbf (1555 daN).

2.2.1.14.7.2 Position 1/2 at 4-5/16 in (110 mm) Height: 2352 lbf (1055 daN).

2.2.1.14.7.3 Position 1/4 at 4-5/16 in (110 mm) Height: 1394 lbf (625 daN).

2.2.1.15 Configuration: DPH-5-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.15.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.15.2 Nominal Height Range: 3-15/16 to 6-7/8 in (100 to 175 mm).

2.2.1.15.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.15.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.15.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.15.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.15.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.15.7.1 Position 1/1 at 6-7/8 in (175 mm) Height: 3768 lbf (1690 daN).

2.2.1.15.7.2 Position 1/2 at 6-7/8 in (175 mm) Height: 2687 lbf (1205 daN).

2.2.1.15.7.3 Position 1/4 at 6-7/8 in (175 mm) Height: 1923 lbf (862 daN).

2.2.1.16 Configuration: DPH-6-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.16.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.16.2 Nominal Height Range: 6-7/8 to 11-7/32 in (175 to - 285 mm).

2.2.1.16.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.16.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.16.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.16.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.16.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.16.7.1 Position 1/1 at 11-7/32 in (285 mm) Height: 3439 lbf (1542 daN).

2.2.1.16.7.2 Position 1/2 at 11-7/32 in (285 mm) Height: 2653 lbf (1190 daN).

2.2.1.16.7.3 Position 1/4 at 11-7/32 in (285 mm) Height: 1611 lbf (722 daN).

2.2.1.17 Configuration: DPH-7-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.17.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.17.2 Nominal Height Range: 11-7/32 to 15-3/4 in (285 to 400 mm).

2.2.1.17.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.17.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.17.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.17.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.17.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.17.7.1 Position 1/1 at 15-3/4 in (400 mm) Height: 2932 lbf (1315 daN).

2.2.1.17.7.2 Position 1/2 at 15-3/4 in 400 mm Height: 2089 lbf (937 daN).

2.2.1.17.7.3 Position 1/4 at 15-3/4 in 400 mm Height: 1327 lbf (595 daN).

2.2.1.18 Configuration: DPH-8-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.18.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.18.2 Nominal Height Range: 14 to 20-9/32 in (356 to 515 mm).

2.2.1.18.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.18.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.18.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.18.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.18.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.18.7.1 Position 1/1 at 20-9/32 in (515 mm) Height: 2817 lbf (1263 daN).

2.2.1.18.7.2 Position 1/2 at 20-9/32 in (515 mm) Height: 1962 lbf (880 daN).

2.2.1.18.7.3 Position 1/4 at 20-9/32 in (515 mm) Height: 1186 lbf (532 daN).

2.2.1.19 Configuration: DPH-9-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.19.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.19.2 Nominal Height Range: 18-9/32 to 24-5/8 in (464 to 625 mm).

2.2.1.19.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.19.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.19.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.19.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.19.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.19.7.1 Position 1/1 at 24-5/8 in (625 mm) Height: 2914 lbf (1307 daN).

2.2.1.19.7.2 Position 1/2 at 24-5/8 in (625 mm) Height: 2000 lbf (897 daN).

2.2.1.19.7.3 Position 1/4 at 24-5/8 in (625 mm) Height: 1253 lbf (562 daN).

2.2.1.20 Configuration: DPH-10-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.20.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.20.2 Nominal Height Range: 21-7/16 to 29-9/64 in (544 to 745 mm).

2.2.1.20.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.20.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.20.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.20.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.20.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.20.7.1 Position 1/1 at 29-9/64 in (745 mm) Height: 2765 lbf (1240 daN).

2.2.1.20.7.2 Position 1/2 at 29-9/64 in (745 mm) Height: 2186 lbf (982 daN).

2.2.1.20.7.3 Position 1/4 at 29-9/64 in (745 mm) Height: 1193 lbf (525 daN).

2.2.1.21 Configuration: DPH-11-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.21.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.21.2 Nominal Height Range: 25-24/64 to 33-15/32 in (645 to 850 mm).

2.2.1.21.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.21.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.21.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.21.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.21.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.21.7.1 Position 1/1 at 33-15/32 in (850 mm) Height: 2947 lbf (1322 daN).

2.2.1.21.7.2 Position 1/2 at 33-15/32 in (850 mm) Height: 2407 lbf 1077 daN).

2.2.1.21.7.3 Position 1/4 at 33-15/32 in (850 mm) Height: 1516 lbf (680 daN).

2.2.1.22 Configuration: DPH-12-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.22.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.22.2 Nominal Height Range: 28-11/32 to 37-51/64 in (720 to 960 mm).

2.2.1.22.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.22.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.22.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.22.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.22.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.22.7.1 Position 1/1 at 37-51/64 in (960 mm) Height: 2899 lbf (1300 daN).

2.2.1.22.7.2 Position 1/2 at 37-51/64 in (960 mm) Height: 2029 lbf (910 daN).

2.2.1.22.7.3 Position 1/4 at 37-51/64 in (960 mm) Height: 1561 lbf (700 daN).

2.2.1.23 Configuration: DPH-13-PH5.

** NOTE TO SPECIFIER ** Delete options for nominal height range not required.

2.2.1.23.1 Nominal Height Range: As scheduled and indicated on Drawings.

2.2.1.23.2 Nominal Height Range: 32-43/64 to 42-1/8in (830 to 1070 mm).

2.2.1.23.3 Top Diameter: 6-1/8 in (155 mm).

2.2.1.23.4 Top Surface Area: 29.14 sq in (188 sq cm).

2.2.1.23.5 Base Diameter: 7-7/8 in (200 mm).

2.2.1.23.6 Base Surface Area: 48.67 sq in (314 sq cm).

2.2.1.23.7 Load Data: Mean value of load at 5 percent slope.

2.2.1.23.7.1 Position 1/1 at 42-1/8in (1070 mm) Height: 2784 lbf (1248 daN).

2.2.1.23.7.2 Position 1/2 at 42-1/8in (1070 mm) Height: 2096 lbf (940 daN).

2.2.1.23.7.3 Positiion 1/4 at 42-1/8in (1070 mm) Height: 1383 lbf (620 daN).

** NOTE TO SPECIFIER ** Delete options for attachment not required.

2.2.1.24 Attachment of Materials to Pedestals: As scheduled and indicated on Drawings.

2.2.1.25 Attachment of Materials to Pedestals: Gravity laid.

2.2.1.26 Attachment of Materials to Pedestals: Fixed to pedestal head.

2.2.1.27 Components: Including but not limited to separation blades/spacer tabs, shims (2 mm), slab supporting heads, slope correctors, height adjusters/couplers, ring clamps for adjustment, locking and unlocking keys to fix pedestal position and supporting bases/stands as follows.

2.2.1.27.1 Supporting Head Surfaces: Adjustable angle from 0 to 5 percent (0 to 5 cm/m).

2.2.1.27.1.1 Diameter: 6-1/8 in (155 mm).

2.2.1.27.1.2 Surface Area: 29.14 sq in (188 sq cm).

2.2.1.27.1.3 Thickness: 5/32 in (4 mm) thick, with reinforcement veins.

2.2.1.27.1.4 Features: Screw on head with a safety clip and 10 mm hole in the center of the head in order to receive the slab separation bladed plate or a raw plug and fixing screw for mechanical attachment.

2.2.1.27.2 Couplers: Height adjusters provide additional height.

2.2.1.27.3 Adjustment Ring Clamps:

2.2.1.27.3.1 Diameter: 4-17/32 in (115 mm).

2.2.1.27.3.2 Description: High to low, to allow height adjustment with decking in place; screw pitch reversed with 3 inner threads and 8 threads factory screwed onto pedestal stand as required for specified designs.

2.2.1.27.4 Supporting Bases:

2.2.1.27.4.1 Base Diameter: 7-7/8 in (200 mm).