1. Specification
working voltage: AC90～250V 50Hz/60Hz
power: 186W
LED spec: 54PCS of 3W RGBW Leds
LED Lifetime: 60,000-100,000 hours
beam angle: 25°
control signal: DMX512
control channels: 7CH(RGB/WA), 8CH(RGBW)
Possible Color Combinations: 16.7 million
2. Operational approach
2.1 Button operation
❤Basic usage
Menu The main menu switch
UP Parameters adjustment
Down Parameters adjustment
Enter confirm/preserve/enter submenu
❤Combination key
It is combinated with two or more button. For example “up+down” means press “up” and “down” at the same time.
The button “up+down” is neither “up”, nor “down” , while it has its own value.
❤Long Press
Keeping press the button at certain time
2.2 Menu manual
2.2.1 function menu
2.2.2 Setting
2.3 Menu manual
2.3.1 Function button
There is showing function button after contact electricity, through “menu” button, it will switch in turn(meanwhile saving function data automatically).
Function button have 11 species in total. At the 3 kinds beginning are slave machine’s function and others are main machine’s function.
❤Note of slave machine function:
1 Undergoing slave machine function, if cut signal source(such as turn off controller or main engine), the lighting will be disconnected automatically
2 If it appeared “function is unnormal” after connect controller, maybe it is influenced by controller’s residual data, please delete all this kind of data inside controller.
❤Function instruction:
Vice machine: equivalenting to “d001”
❤Button operation:
It’s unavailable on this menu for “up/down/enter”.
❤Function instruction:
Slave machine: at DMX normal state, receiving data from main machine or controller data.
If your lighting featured 3 colours, please use according 3 channels:
Chanel position / Value / Function instruction1 / 0~255 / Red
2 / 0~255 / Green
3 / 0~255 / Blue
If your lighting featured 4 colours, please use according 4 channels:
Chanel position / Value / Function instruction1 / 0~255 / Red
2 / 0~255 / Green
3 / 0~255 / Blue
4 / 0~255 / White
❤Button operation:
Pressing “up/down” and choosing address code(1~512)
Pressing “enter” and preserving the address code (it will preserve all address code automatically next time).
❤Note:
The accumulator of address code is relative with channel’s choice. If you use 3 channels ,then cumulate 3.For example,the first piece (set) of light’s address code is 001,then the second piece(set) is 004…If you use 4 channels ,then cumulate 4.For example, the first piece(set) of light’s address is 001,then the second piece(set) is 005.
❤Function instruction:
Vice machine: at senior DMX state, receiving the data from controller only. According to 8 channels regularly:
CH1A001 / CH2
d001 / Channel / Value / Function
1 / Dimmer / 0~255
2 / Strobe / 0~5 / On
6~10 / Off
11~100 / Impusle strobe（slow to fast）
101~150 / gradual-on strobe（slow to fast）
151~200 / gradual-off strobe（slow to fast）
201~255 / sudden strobe（slow to fast）
3 / Effect/Mode / 0~5 / Manually change colour（R,G,B……）
6~50 / colour change(fade)
51~100 / colour change (gradual on)
101~150 / sudden colour change
151~200 / Auto(Unused for other channel)
201~255 / Sound(Unused for other channel)
4 / Speed / 0~255 / Ch3 work，control speed of colour changing or auto
5 / 1 / Red / 0~255 / Linear dimming
6 / 2 / Green / 0~255 / Linear dimming
7 / 3 / Blue / 0~255 / Linear dimming
8 / 4 / White / 0~255 / Linear dimming
❤Button operation:
Press up/down is choosing address code (1~512)
Press enter is preserving address code (preserving all address code automatically next time when connecting election.
❤Note:
1. The increasing number of address code is 8. For example ,the first piece(set) lights’ address code is 001, while the second is 009 and the third is 017…
2. If there was implement “several machine synchronous”, the current effect will be from the start over when using NO.8 adjustable. Please see the first point on preceding page “several machine synchronous”
❤Note of main machine function:
When the light undering send data state. if there is any other light undering vice machine state, please turn off extra main machine. At the same time, please turn off or cut controller. (Each vice machine only receiving one controller’s signal, otherwise probable made the light change irregularlly.)
❤Function instruction:
Main machine: at the state of color fade.
❤Button operation:
Press up/down is choosing speed
Press enter is preserving speed (preserve all speed automatically next time when connecting election)
❤Note:
Please see “note of main machine function” on front page.
❤Function instruction:
Main machine: at the state of color jump.
❤Button operation:
Press up/down is choosing speed
Press enter is preserving speed (preserve all speed automatically next time when connecting election)
❤Note:
Please see “note of main machine function” on front page.
❤Function instruction:
Main machine: at the state of color pulse.
❤Button operation:
Press up/down is choosing speed
Press enter is preserving speed (preserve all speed automatically next time when connecting election)
❤Note:
Please see “note of main machine function” on front page.
❤Function instruction:
Main machine: at the state of color tone.
❤Button operation:
Press enter is preserving current data and switch submenu at the same time.
Submenu is to color alphabet beginning, following are three figure(e.g.: 000)
Press up/down under submenu can change figure.(0~255)
❤Note:
Please see “note of main machine function” in the past page.
❤Function instruction:
Main machine: at the state of sound control.
You can customize stroboscopic color. If the color’s number is 0 respectively in the menu “rGbW”, it strobe by white. Otherwise, it strobe by means of allocated color in the menu “rGbW”.
❤Button operation:
Useless of button up/down/enter in this menu.
❤Note:
Please see “note of main machine function” in the past page.
❤Function instruction:
Main machine: at the state of sound control.
❤Button operation:
Useless of button up/down/enter in this menu.
❤Note:
Please see “note of main machine function” in the past page.
❤Function instruction:
Main machine: at the state of demo.
❤Button operation:
Useless of button up/down/enter in this menu.
❤Note:
Please see “note of main machine function” in the past page.
❤Button operation:
Press enter at certain time is enter setting menu.
2.3.2 setting menu
There are 7 items in total and switch by menu in turn.
❤Function instruction:
Setting screen saver and wait for a while(1-90 seconds, the default figure is 30 seconds). Under function menu(the program is operating normally), it is enter at state of screen saver if waiting more than this figure and not press any button.
It will forbid screen saver if set to 0.
❤Button operation:
Press up/down can change figure.(0~90)
❤Note:
Screen saver is used in function menu only. It never unavailable under setting menu.
When undergoing state of screen saver, it is useless for button “menu/up/down”. Only press enter key and then loosen, can it exit state of screen saver. (Be ensure do not made errior operation since you cannot see the content on screen.)
❤Function instruction:
Partial color revise (adjust the largest proportion of each color, that is so-called “through software adjust current.)
The default number is 255 respectively.(100%)
❤Button operation:
Press enter key switch submenu.
Submenu is to color alphabet beginning, following are three figure(e.g.: r255)
Press up/down under submenu can change figure.(0~255)
❤Control adjustable:
Methods on above can adjust single light only.
If adjust a set of light synchronous by controller, as following:
Press combination key “up+down” when appearing “CSAd”, and then loosen when it become “CSdA”. (If it connected controller and used “signal flash”, you may see screen flash when loosen.) This time is enter the pattern of control adjustable and the light is on the state of slave machine as well as receiving four kinds of color’s largest ratio from No.1 to No.4 channels what undergoing red, green, blue, white respectively.
Press enter and exit the mode of control adjustable. Then, you shall see the number received from controller though submenu “r255”. If it is not satisfied, you may adjust one by one, or enter the state of mode of control adjustable by adjust controller.
Only press the key of “up+down”, can it open the mode of control adjustable. Because when enter this mode, may receive the number immediately from controller instead of setting number originally. This is to say, the original number that set will be lost. Taking the measure to avoid the case.
❤Function instruction:
Power choice. “HPon” represent turn in high power.(default)
“HPoF” represent turn off high power.
Turn on high power = actual power ×100%
Turn off high power = actual power ×33.3%
❤Button operation:
Press up is turn on. (appeared “HPon”)
Press down is turn off. (appeared “HpoF”)
❤Function instruction:
“ddon” represent push rod delay with turn on controller.(default); “ddoF” represent push rod delay with turn off controller.
❤Button operation:
Press up is turn on. (appeared “ddon”)
Press down is turn off. (appeared “ddoF”)
❤Function instruction:
If this light as the slave machine and the screen will flash when receiving control signal from controller or main machine.
❤Button operation:
Press up is turn on.(appeared “Sfon”)
Press down is turn off.(appeared “SfoF”)
❤Note:
If the light at the state of main machine, the screen will cannot flash even receiving control signal.
❤Function instruction:
“Syon” represent turn on “many machine synchronous”
“SyoF” represent turn off “many machine synchronous” (default)
❤Button operation:
Press up is turn on.(appeared “Syon”)
Press down is turn off.(appeared “SyoF”)
❤Button operation:
Press ENTER at certain time will preserve setting data and back to “Set” menu.
- 1 -