The Commercial Division of USFLOORS INC
3580 Corporate Dr. 30721 | 877.292.4044
Natural Bamboo® Strand Woven Engineered Plank - ENDURA AR+
construction document 096223
All references included in this document refer to USFloors as the product manufacturer. Natural Bamboo® is a trade brand name represented under the exclusive control of USFloors Inc.
PART 1: General
1.1 QUALITY ASSURANCE
A. Qualifications:
1. Manufacturer Qualifications:
a) Minimum 10 years of experience in manufacturing and distributing bamboo flooring of the type specified.
b) Member: National Wood Flooring Association, United States Green Building Council
c) Manufacturer must have legal right to the patented process and glues used in the production of specified strand woven bamboo flooring.
d) Manufacturer uses best practices of environmental stewardship in harvesting, milling, and shipping
2. Installer Qualifications:
a) Minimum three years of experience in hardwood flooring installation
b) National Wood Flooring Association Certified Professional
B. RELATED DOCUMENTS
1. Responsibility and submittal of drawings and general provisions of the contract is the responsibility of the general contractor and the flooring contractor, including general and supplemental conditions
2. Submittals of USFContract printed product data, test reports and installations- Included shall be materials, finishes, required substrate preparation, adhesive and accessories
3. Two samples of product to submitted to illustrate product shade, design and finish samples are the standard for materials installed
4. Submittals of sustainable practices and materials as outlined in USGBC – LEED credit documentation. Referred credit review for this specifications document include but are not limited to:
a) MR Rapidly Renewable Materials
b) EQ Low Emitting Materials
c) ID Innovative Design
C. DELIVERY, STORAGE, AND HANDLING
1. Materials delivered in the original packages, with seals unbroken, bearing USFContract labels indicating product identification
2. To prevent damage and loss, store in secure climate controlled space
3. Store cork flooring on flat surface in accordance with USFContract handling instructions
4. Custody and disposal of all materials must comply with requirements of local authorities having jurisdiction
D. SITE CONDITIONS
1. Do not deliver or install cork planks until all trowel trades are completed, building is enclosed and weather tight, and permanent heating, air conditioning, ventilating and lighting are installed and operating.
2. Move product into installation area at least seventy-two hours prior to installation for acclimation
3. Install flooring subsequent to finishing operations ; including painting
4. Cover areas of flooring where contractor traffic may occur after installation to protect from damage
5. Maintain temperatures and humidity in accordance to USFContract installation procedures
E. WARRANTY
1. USFContract will provide a warranty statement of products in a commercial application in accordance to specific products and applications. Refer to USFContract product specification guide.
PART 2: PRODUCTS
2.01 MANUFACTURER
USFContract
The Commercial Division of USFloors Inc
3580 Corporate Drive
Dalton, GA 30721 USA
www.USFContract.com | 877.292.4044
2.02 MATERIALS
A. Acceptable Product: Bamboo Basics Natural
1. SKU: BSWE-100
2. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
3. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
4. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
5. Requests for substitutions considered in accordance with provisions of Section 01600.
6. Substitutions: Not permitted
B. Acceptable Product Bamboo Basics Spice
1. SKU: BSWE-101
2. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
3. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
4. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
5. Requests for substitutions considered in accordance with provisions of Section 01600.
6. Substitutions: Not permitted
C. Acceptable Product Bamboo Basics Corboo Horizontal Natural
1. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
2. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
3. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
4. Requests for substitutions considered in accordance with provisions of Section 01600.
5. Substitutions: Not permitted
D. Acceptable Product Bamboo Basics Corboo Horizontal Spice
6. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
7. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
8. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
9. Requests for substitutions considered in accordance with provisions of Section 01600.
10. Substitutions: Not permitted
E. Acceptable Product Bamboo Hues Strand Woven Spice Vol. 1
1. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
2. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
3. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
4. Requests for substitutions considered in accordance with provisions of Section 01600.
5. Substitutions: Not permitted
F. Acceptable Product Bamboo Hues Strand Woven Natural Vol. 2
11. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
12. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
13. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
b) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
14. Requests for substitutions considered in accordance with provisions of Section 01600.
15. Substitutions: Not permitted
G. Acceptable Product Bamboo Hues Corboo™ Horizontal Spice
1. Physical Properties
a) Flammability Passes “life Safety Codes”
b) Smoke Density ASTM E662 Flaming 342 – Non-flaming 357
c) Critical Radiant ASTM E648 Flux: 0.49W/cm2 NFPA 101 Classification type
d) 1 Slip Resistance: ASTM D 2394 Static 0.6 Dynamic 0.5
e) Flammability: Passes “life Safety Codes”
f) ASTM E 648 Class 1
g) Smoke Density: ASTM E 84 <25 Flame
h) IAQ : GREENGUARD Children and Schools
i) VOC Emissions: CARB12 Compliant
2. Performance Properties
a) Abrasion Resistance: 1500 revolutions
b) Density Impact: ASTM 1037 Janka test data +2700
3. Installation
a) Adhesive:
1) One part premium wood floor adhesive Greenguard Certified
a) Nails or Staples:
1) 1-1/2 Inch (38 mm) Thick Subfloor: 2 inch nails or staples
2) 3/4 Inch (19 mm) Thick Subfloor: 1-1/2 inch nails or staples
3) 1 inch Thick Plywood Subfloor Over Concrete: 1-1/4 inch (32 mm) nails or staples
4. Requests for substitutions considered in accordance with provisions of Section 01600.
5. Substitutions: Not permitted
PART 3 – EXECUTION
3.01 EXAMINATION
A. Examine substrates prior to installation
B. Verify that subfloor is clean, dry, and free of contaminates that would interfere with adhesive bond.
C. Concrete installation: Test concrete floors for moisture content using a Calcium Chloride test or Tramex Moisture Encounter meter.
1. Do not install flooring if vapor pressure exceeds 3 lbs per 1,000 sf (15 g per m2) in 24 hours, as under these conditions “urethane” adhesives tend to fail.
2. In multiple story buildings, test each floor level
3. Mark test location(s) on As-Built Drawings
D. The subfloor moisture content is not to exceed 14% for plywood substrate.
1. In multiple story buildings, test each floor level
2. Mark test location(s) on As-Built Drawings.
E. Verify that HVAC system is operating and maintaining occupancy level temperature and humidity conditions.
F. If either of the above requires attendance, coordinate with responsible entity to correct unsatisfactory conditions.
3.02 PREPARATION
A. Acclimatization:
1. Open all bundles, and let acclimate for a minimum of 72 hours.
2. Fix the substrate to ensure bumps and depressions are less than 1/8” over 10 feet.
3.03 INSTALLATION
A. Install in accordance with manufacturer's installation instructions by either:
1. nailing or stapling to substrate
2. gluing to substrate
3. nailing or stapling and gluing to substrate
4. Lay flooring in the direction(s)/pattern(s) as shown on Drawings.
5. Inquire for Strandwoven™ Installation Guidelines.
6. Accessories: Install using methods appropriate to the accessory and flooring system.
3.04 CLEANING
A. Clean in accordance to Manufacturer’s Maintenance Recommendations. Inquire for strand woven maintenance guidelines.
3.05 PROTECTION
A. Remove visible adhesive and other surface blemishes using cleaner as recommended.
B. Do not wash floor for at least five days following installation
C. When the planks sufficiently seats (in no case less than five days), clean in accordance with USFloors written directions.
D. After cleaning the flooring surface, it is necessary to protect the floor from mars, indentations, paint drippings, or other damage by either using building paper or by keeping traffic off the floors until the building is ready for occupancy.
E. Do not use non-breathable sheet or film that could cause condensation to form. Maintain covering throughout remainder of construction period
F. Should the floors become dirty or damaged prior to final acceptance by the Owner, they shall be repaired, recleaned, refinished, or replaced as required so that the Owner will receive floors ready for occupancy without additional cleaning before using.
1.05 OPERATIONS AND MAINTENANCE DOCUMENTS
A. Upon completion of floor installation the owner, attendants or individuals in charge responsible for upkeep of building are to follow care and maintenance instructions. Wait 48 hours after completion of installation and application of any finish before beginning maintenance program. Use finish manufacturer's maintenance instructions for bamboo floors, which have finish applied on site. Use USFloors maintenance instructions for prefinished bamboo floors that do not have extra finish applied on site.
B. The General Contractor shall supply original copies of all Natural Bamboo® flooring cleaning and maintenance information provided by USFloors. The Owner’s maintenance personnel must receive this information upon completion of work.
USFC- Natural Bamboo® Strand Woven - Endura AR+ construction document Page 1 of 6
Revised 05_2012