Pittco Architectural Metals, Inc.08930
Pittco TMW 450ALUMINUM GLAZED CURTAINWALL
2006 - Digicon Information Inc.Page 1
This section addresses Pittco TMW 450 Flush Glaze Storefront Curtain Wall System, mounted from the exterior and includes an aluminum frame assembly and double pane sealed unit glazed lite, for exterior and interior applications, shop fabricated, factory pre-finished, including field glazing. The system application is intended for multiple storys. For single story glazing systems, consider utilizing Pittco Sections 08420, 08421, 08422, 08423, 08424, 08425, 08426. Glass and glazing is referenced to Section 08800. Sealants are referenced to Section 07900. Door hardware may be specified in this section or specified in Section 08710; edit text accordingly. Operable sash, if any, is usually specified in Aluminum Windows - Section 08520. Where work of this section integrates with another glazing assembly, carefully coordinate both sections to function together. Air barrier and vapor retarder continuity from this system to adjacent construction is critical to successful building air and moisture tightness; specify compatible materials in conjunction with Sections 07260 and 07270. This section includes performance, proprietary, and descriptive type specifications. Edit to avoid conflicting requirements.
PART 1GENERAL
1.1SECTION INCLUDES
A.Aluminum glazed frame storefront assembly.
B.Double pane sealed unit vision glass.
Include the following paragraph if door hardware is specified in Part 2 of this section; delete the following paragraph if hardware is referenced to Section 08710 - Door Hardware.
C.Furnish [Pittco Standard Door Hardware] [Custom Door Hardware indicated in Part 2] [Door Hardware referenced in Section 08710].
D.Perimeter sealant.
1.2RELATED SECTIONS
Select and edit the paragraphs in this article - delete those that do not apply to the Project.
A.Section [______-______]: Preparation of adjacent work to receive work of this section.
B.Section 05500 - Metal Fabrications: Steel fabricated [attachment devices.] [framed openings.]
C.Section 07260 - Vapor Retarders: Vapor seal at adjacent construction.
D.Section 07270 - Air Barriers: Air seal at adjacent construction.
E.Section 07900 - Joint Sealers: Assembly perimeter sealant and back-up materials.
Select one or both of the following two entrance door and frame assemblies for wall openings within this glazed assembly, as may be applicable for a project.
F.Section 08121 - Standard Aluminum Entrances: Door and frame assembly to fit within this glazed assembly.
G.Section 08123 - Monumental Aluminum Entrances: Door and frame assembly to fit within this glazed assembly.
H.Section 08520 - Aluminum Windows: Operable sash within framing members of this section.
Select and edit the paragraphs in this article - delete those that do not apply to the Project. Include the following paragraph if hardware is referenced to Section 08710 - Door Hardware.
I.Section 08710 - Door Hardware: Mortised hardware reinforcement requirements affecting framing members.
The following paragraph describes automatic door operating hardware.
J.Section 08740 - Automatic Door Equipment.
K.Section 08800 – Glazing.
L.Section 09910 - Painting: Field painting of interior surface of infill panel [and [______]] surfaces.
M.Section [______-______]: Wall fin convectors and support saddles attached to framing members.
1.3REFERENCES
List reference standards that are included within the text of this section. Edit the following as required for project conditions.
A.AA (Aluminum Association) - Designation System for Aluminum Finishes.
B.AAMA MCWM-1 - Metal Curtain Wall Manual.
C.AAMA CWG-1 - Installation of Aluminum Curtain Walls.
D.AAMA 501.2-03 - Quality Assurance and Diagnostic Water Leakage Field Check of Installed Storefronts, Curtain Walls, and Sloped Glazing Systems.
E.AAMA 503-92, Voluntary Specification for Field Testing of Metal Storefronts, Curtain Walls, and Sloped Glazing Systems.
F.AAMA 1503-98 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors, and Glazed Wall Sections.
G.ASTM A123/A123M - Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.
H.ASTM A653/A653M - Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.
Select one of the following standards if applicable; paragraph I is for "inch/pound" measure, paragraph J is for "metric" measure.
I.ASTM B209 - Aluminum and Aluminum-Alloy Sheet and Plate.
J.ASTM B209M - Aluminum and Aluminum-Alloy Sheet and Plate [Metric].
Select one of the following standards if applicable; paragraph K is for "inch/pound" measure, paragraph L is for "metric" measure.
K.ASTM B221 - Aluminum-Alloy Extruded Bar, Rod, Wire, Shape, and Tube.
L.ASTM B221M - Aluminum-Alloy Extruded Bar, Rod, Wire, Shape, and Tube [Metric].
M.ASTM E283 - Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors.
N.ASTM E330 - Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
O.ASTM E331 - Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
1.4SYSTEM DESCRIPTION
Use this article carefully; restrict statements to describe components used to assemble the system. Do not repeat statements made in the Section Includes article.
A.Aluminum entrances and storefront assembly includes tubular and split aluminum sections with supplementary internal framing, shop fabricated, factory finished, vision glass, related flashings, anchorage and attachment devices.
Fabrication and erection of the glazed frame assembly is usually left to the prerogative of the assembly fabricator. If site conditions, opening tolerances or quality of the work may be an issue or a concern, it may be prudent to require either shop assembly or field erection of the frame assembly. Select one of the following options as appropriate.
B.Frame Assembly: [Site assembled.] [Shop unitized assembly.]
1.5PERFORMANCE REQUIREMENTS
Use this article carefully; restrict statements to identify system performance requirements or function criteria only. Delete paragraphs not appropriate to project. Performance specifying permits system manufacturers the latitude to adjust proprietary systems to achieve specified requirements. Rely on this article as the basis for assembly criteria specifying and minimize the material and component statements so not to conflict with performance criteria. The following paragraphs represent a suggested listing of criteria. If more stringent criteria is being considered, refer to AAMA and ASTM test methods and associated documents for guidance.
A.Assembly Design: Design and size components to withstand dead and live loads caused by positive and negative wind pressure acting normal to plane of wall as calculated in accordance with code.
B.Assembly: Accommodate without damage to components or deterioration of seals, movement within system, movement between system and peripheral construction, dynamic loading and release of loads, deflection of structural support framing.
For mullion, corner, and special change of wall plane conditions, limit glazing sealant design movement to 20 percent maximum for elastomeric sealants or 5 percent for acrylic or butyl sealants. Special conditions may require special statements in the paragraph below; edit accordingly.
C.Structural Performance - Deflection: Limit mullion deflection to [flexure limit of glass,] [1/175] [______] of span as measured in accordance with ASTM E330; with full recovery of members.
D.Air Infiltration: Limit air leakage through assembly to [0.06] [____] cfm/sq ft of wall area, measured at a reference differential pressure across assembly of [1.57] [____] psf ([75] [____] Pa) as measured in accordance with ASTM E283.
E.Static Water Leakage: None, when measured in accordance with ASTM E331 with a test pressure difference of [ 10] [____] lb/sq ft ([480] [____] Pa).
F.Dynamic Water Leakage: None, when measured to AAMA 501.2, with a test pressure difference of [ 10] [____] lb/sq ft ([480] [____] Pa).
G.Condensation Resistance Factor (CRF): 58 when measured to AAMA 1503.
H.Insulation U-Factor: 0.58 BTU/hr/sq ft/degrees F when measured to AAMA 1503.
I.Air and Vapor Seal: Maintain continuous air barrier and vapor seal throughout assembly, primarily in line with pane of glass
J.Expansion / Contraction: Provide for expansion and contraction within door and frame assembly components caused by ambient cycling temperature range of [170] [______] degrees F ([95] [______] degrees C over a twelve (12) hour period based on a metal installation temperature of 85 degrees F ([29] degrees C) without causing detrimental effect to assembly components and anchorage.
K.System Internal Drainage: Drain water entering joints, condensation occurring in glazing channels, or migrating moisture occurring within system, to the exterior by a weep drainage network.
1.6SUBMITTALS FOR REVIEW
Do not request submittals if drawings sufficiently describe the products of this section or if proprietary specifying techniques are used. The review of submittals increases the possibility of unintended variations to drawings, thereby increasing the Specifier's liability. The following submittals are intended for review and approval or other action by the Specifying Authority.
A.Section [01300:] [______:] Submission procedures.
B.Product Data: Provide component dimensions, describe components within assembly, anchorage and fasteners, glass, [door hardware,] internal drainage details and [______].
C.Design Data: Provide framing member structural and physical characteristics, [calculations,] dimensional limitations.
D.Shop Drawings: Indicate system dimensions, framed opening requirements and tolerances, affected related Work and expansion and contraction joint location and details.
Use the following paragraph for submission of physical samples for selection of finish, color, texture, etc.
E.Submit [two] [______] samples [1-3/4 x 4 inch] [____x____] inch [45 x 100 mm] [____x____] mm in size illustrating finished aluminum surface.
F.Submit [two] [______] samples [12 x 12 inch] [____x____] inch [305 x 305 mm] [____x____] mm illustrating glass infill, glazing materials.
1.7SUBMITTALS FOR INFORMATION
The following submittals are informational; responsive action by the Specifying Authority is not required.
A.Section [01300:] [______:] Submission procedures.
B.Manufacturer's Certificate: Certify that [Products] [______] meet or exceed [specified requirements.] [______.]
1.8SUBMITTALS AT PROJECT CLOSEOUT
The following submittals are for project close-out purposes.
A.Section [01700:] [______:] Submission procedures.
B.Submit manufacturer warranty and ensure forms have been completed in Owner’s name and registered with manufacturer.
1.9QUALITY ASSURANCE
Only include this article if the specified system is extensive and warrants special design attention. The subsequent paragraph is to address requirements of the handicapped.
A.Design and fabricate to AAMA MCWM-1.
B.Perform Work to AAMA CWG-1.
C.Manufacturer [and Installer]: Company specializing in manufacturing aluminum glazing systems with minimum [three] [______] years [documented] experience.
D.Design structural support framing components under direct supervision of a Professional Structural Engineer experienced in design of this Work and licensed at the place where the Project is located.
1.10PRE-INSTALLATION MEETING
A.Section [01300:] [______:] Pre-installation meeting.
B.Convene [one] [_____] week before starting work of this section.
1.11DELIVERY, STORAGE, AND PROTECTION
A.Section [01600:] [______:] Transport, handle, store, and protect products.
Only include the following paragraph if the specified system is extensive and warrants special handling.
B.Handle Products of this section in accordance with AAMA – Curtain Wall Manual #10.
C.Protect finished aluminum surfaces with [wrapping] [removable protective material]. Do not use adhesive papers or sprayed coatings which bond when exposed to sunlight or weather.
1.12PROJECT CONDITIONS
A.Section [01300:] [______:] Coordination and meetings.
In the following paragraph, only include the firestopping, air barrier, and vapor retarder barrier option statements if that work is specified in other sections.
B.Coordinate the Work with installation of [firestopping,] [air barrier,] [vapor retarder,] [and] [______] components or materials.
1.13ENVIRONMENTAL REQUIREMENTS
A.Section [01600:] [______:] Environmental conditions affecting products on site.
If dry glazing methods are utilized, delete this article.
B.Do not install sealants when ambient temperature is less than [40] [____] degrees F ([5] [____] degrees C) during and [48] [____] hours after installation.
1.14WARRANTY
Improper specifying of warranty and correction period extensions may limit the statutory rights of the owner and the ability to enforce claims under the contractor's contractual warranty. Consult legal counsel before editing this article.
A.Section [01700:] [______:] Warranties.
The following paragraph extends the correction period beyond one year. An extended correction period adds to the construction cost and may not be enforceable.
B.Correct defective Work within a [one (1)] [five (5)] [____] year period after Substantial Completion.
C.Warranty: Include coverage for complete system for failure to meet specified requirements.
The following paragraph requests a manufacturer warranty; the request may not be effective as the manufacturer is outside the jurisdiction of the Owner/Contractor contract. Coordinate this paragraph with the Submittals at Project Closeout article. Manufacturer's warranty for glass is described in Section 08800.
D.Provide [five (5)] [____] year manufacturer warranty for glazed units.
PART 2 PRODUCTS
2.1MANUFACTURERS
The following manufacturer and their product should be used for the creation of drawing details and door schedules. Specify the following paragraph alone or add the second paragraph indicting other manufacturers who are also permitted to bid, providing their product conforms to or exceeds these specification requirements.
A.Base Product: Pittco Architectural Metals, Inc., “TMW 450 Framing System of [single tube] [split tube] Design”. Phone 800-992-7488, Fax 847-593-9946, Internet web site at
Edit the following paragraphs and other descriptive specification requirements elsewhere in this section to eliminate any conflict with the following "other" manufacturer's products.
B.Other acceptable manufacturers conforming to specified requirements:
1.[______].
2.[______].
C.Substitutions: Not permitted.
2.2MATERIALS
A.Extruded Aluminum: [ASTM B221,] [ASTM B221M,] 6063 alloy of T5 temper.
B.Sheet Aluminum: [ASTM B209.] [ASTM B209M.] [______.]
C.Sheet Steel: [ASTM A653/A653M] [______]; galvanized in accordance with [______].
D.Fasteners: [Stainless] [Galvanized] steel.
2.3COMPONENTS
The following paragraph identifies the nominal dimensions of the primary framing members. If performance specifying, ensure no conflict exists.
A.Frame:
1.Exposed to View Nominal Width: 2 inch (51 mm),
2.Nominal Depth: 6-13/16 inch (173 mm),
3.Frame assembly thermally broken design,
Depth of glazing pocket is important for glass pane or glass unit glazing bite for retention in frame, depth is also important for glass edge free space due to expansion and contraction of glass due to cycling thermal changes.
4.Glazing Pocket Depth: 5/8 inch (16 mm).
5.Intermediate and sill horizontal members,
6.Mounting and attachments from the exterior.
7.Flush snap-in glazing stops,
8.Drainage holes; internal weep drainage network.
Include the following paragraph if the vertical mullion members require additional strength for span distance or wind/suction loads.
B.Reinforced Mullion: Extruded tubular aluminum section with internal reinforcement of shaped steel channel-shaped section or extruded aluminum section.
C.Doors: Specified in Section [08121.] [08123.]
Include the following paragraph if the Hardware Schedule is part of Section 08710 if doors are included in this assembly. Do not identify hardware for doors if hardware is specified in the door specification section(s).
D.Door Hardware: Specified in Section [08710.] [______.]
E.Flashings: 0.032 inch (0.8 mm) thick [aluminum,] [galvanized steel,] [______] finish [as selected.] [to match mullion sections where exposed.]
Integral operable windows are usually specified in another section. Edit the following paragraph accordingly.
F.Operable Sash: Specified in Section [08520] [______], hopper or awning.
Adjacent air barriers and vapor retarders are usually specified in another section. Drawing details should diagramatically indicate the plane of the vapor retarder and the plane of the air seal. Edit the following paragraphs accordingly.
G.Vapor Retarder: [Specified in Section [07260] [______].] [Sheet EPDM.] [______.]
H.Air Barrier: [Specified in Section [07270] [______].] [Sheet steel, galvanized.] [______.]
2.4GLASS AND GLAZING MATERIALS
Incorporate glass or plastic and glazing materials by direct reference to Section 08800. The following paragraphs only describe glass or plastic types; coordinate with a schedule in Section 08800.
A.Glass: Specified in Section 08800, of type described below:
1.Outer Pane: [Float] [Heat-strengthened] [______], [Clear.] [______.]
2.Space: [Dry air.] [Argon gas.]
3.Inner Pane: [Float] [Heat-strengthened] [______], [Low-E coating on #3 surface,] [Clear.] [______.]
4.Unit Nominal Thickness: [1] [____] inch ([25] [____] mm).
5.Insulation U-Value: [____] BTU/hr/sq ft/degrees F.
B.Glazing Materials: [Closed cell foam, to suit application and achieve weather, moisture, and air infiltration requirements.] [As specified in Section 08800.]
2.5SEALANT MATERIALS
Incorporate sealant materials by direct reference to Section 07900. The following paragraphs only describe sealant type; coordinate with schedule in Section 07900. Sealants used for glazing are specified in Section 08800.
A.Sealant and Backing Materials:
1.Perimeter Sealant: [______] type as specified in Section [07900.] [______.]
2.Sealant Used Within System (Not Used with Glazing): [______] type specified in Section [07900.] [______.]
2.6FABRICATION
A.Fabricate components with minimum clearances and shim spacing around perimeter of assembly, yet enabling installation and dynamic movement of perimeter seal.
B.Accurately fit and secure joints and corners. Make joints flush, hairline, and weatherproof.
C.Prepare components to receive anchor devices. Fabricate anchors.
D.Arrange fasteners and attachments to conceal from view.
The following paragraph would only apply if blinds or draperies are intended at the interior side of the glazed wall assembly, and the dead weight and operating loads of such items warrant attachment reinforcement in this section.
E.Reinforce interior horizontal head rail to receive [drapery] [blind] [______] track brackets and attachments.
F.Prepare components with internal reinforcement for door hardware [and door operator hinge hardware].
G.Reinforce framing members for imposed loads.
2.7FINISHES
The wide variety of finishes for aluminum preclude listing all the available options; the following paragraphs offer the commonly specified finishes, either by reference to AAMA finishes or by generic or proprietary description. Specify the anodizing color whenever possible, as the cost varies considerably between colors. The AAMA A40 series finishes are anodized 0.7 mils (0.018 mm) thick or greater (termed Architectural Class I); A41 is clear, A42 has integral color, A43 has impregnated color, A44 is anodized in two steps. The A20 and A30 series coatings are thinner.
A.Exposed Aluminum Surfaces: AA M12 C22 A31, anodized to Clear color.
[OR]
B.Exposed Aluminum Surfaces: AA M12 C22 A44, anodized to [______] color.
[OR]
C.Hardcoat Coating: [#60 Light Bronze.] [#61 Medium Bronze.] The latter two types are not standard finishes and require longer lead delivery times and are priced as a special order. [#62 Dark Bronze.] [#63 Black.]
The following three coating processes are proprietary, the latter two types are not standard finishes and require longer lead delivery times and are priced as special order.
[OR]
D.Finish of Exposed Aluminum Shall be Compliant With the Performance Standards Set Forth in AAMA Specification 2604-05, “High Performance Organic Coatings on Aluminum.”