2
March 2009
AmericasBosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450,
USA
Phone: + 1 800 289 0096
Fax: +1 585 223 9180
www.boschsecurity.us / Europe, Middle East, Africa
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
www.boschsecurity.com / Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
www.boschsecurity.com
Product Guide Specification
SECTION 28 23 13
ALLEGIANT MATRIX/CONTROL SYSTEMS–MODULAR
BOSCH LTC 8900 SERIES Allegiant Matrix/Control Systems - Modular
PART 1 – GENERAL
1.1 SUMMARY
A. Section Includes
1. Digital Video Recorders and Analog Recording Devices.
B. Related Sections
1. Section [28 23 16 – Video Surveillance Monitoring and Supervisory Interfaces].
2. Section [28 23 23 – Video Surveillance Systems Infrastructure].
1.2 REFERENCES
A. EMC U.S. and Canada
1. ICES-003
B. EMC Europe
1. 89/336/EEC
2. Immunity: EN50082-1
3. Emission: EN50081-1 Class A.
C. Federal Communications Commission
1. FCC Part 15, Class A
D. International Organization for Standardization (ISO) (www.iso.ch)
1. ISO 9001 – Quality Management Systems.
E. Underwriters Laboratories, Inc. (UL).
1. UL 6500
2. UL 1950
F. Canadian Standards Association (CSA)
1. CSA E65
2. CSA 950
G. Safety
1. LVD Requirements: 73/23/EEC; EN60065
1.3 DEFINITIONS
A. Biphase: Pan/Tilt/Zoom protocol for Bosch products.
B. Bilinx: A communications format that allows remote control, configuration and updates to be performed over the video cable (Coax or Passive UTP).
C. SalvoSwitching: Capability where any number of system monitors may be selected to switch as a group.
D. SatelliteSwitch: Enables a single LTC 8900 system to communicate with the remotely located satellite systems.
1.4 SYSTEM DESCRIPTION
A. The product described in this specification shall be a high density, full cross-point video matrix switcher/control system capable of seamlessly switching up to 4096 camera inputs to any or all of 512 monitor outputs and provide Bosch biphase control protocol for control of compatible remote receiver/driver units and/or full proportional, variable/high speed dome cameras. The system shall provide 16- or 40-character camera titles, two-digit site plus 4-digit camera identification numbers, and 12-character monitor titles.
B. The video matrix switcher/controller system shall consist of a dual/redundant CPU and Power Supply unit with automatic hot switchover capability; modular video input and output bays; up to 120 full-function system keyboards for switching, control, and programming; primary and backup LAN switches; and a system controller PC running Windows XP Professional and provided with a keyboard, mouse, CD/DVD burner, floppy disc drive, and an LCD flat-screen monitor.
C. Video Switcher/Controller System Components:
1. The CPU Bay shall provide central control for the entire video matrix switching system. The CPU shall contain the system’s configuration information and shall be the connection interface to the various external accessories such as keyboards, alarm interfaces, and camera control signal distribution unit.
a. The CPU bay shall utilize redundant CPU boards and redundant power supplies that provide a “hot standby” operation that, in conjunction with a System Controller PC, automatically switches-over to the back up in the event of a main power supply failure or CPU fault.
b. The CPU shall provide “data mirroring” technology that allows the backup CPU to constantly maintain the same operational state as the main CPU, so that in the event of a switchover to the backup CPU, all appropriate video will be on the system monitors, sequences will continue to run, and alarms will be active. Any data transfers to the backup CPU shall be automatically verified to ensure accuracy.
c. The CPU bay front panel shall have a switch that allows the CPU to be manually switched between the primary and backup CPU or placed in the Auto Mode that allows automatic switchover from the primary to the backup in case of a CPU or power supply failure.
2. Video input bays shall be modularized and provide the video switching functions. A single video input bay shall be capable of switching 256 cameras to 64 video outputs that will provide video to the output bays that generate the text overlays for 64 monitor outputs. Additional input bays shall be easily added to the system configuration to provide up to 4096 inputs. Video input bays shall have video looping capability.
3. Video output bays accept the switched video from the input bays and generate the text overlays for up to 64 video display monitors connected to that bay. Additional output bays shall be easily added to the system configuration to provide up to 512 outputs.
4. An industrial grade System Controller Pentium PC utilizing the Windows® XP Professional operating system, 512 MB RAM (minimum), an 8GB solid state hard drive, and pre-loaded with the necessary system configuration software shall be provided that is dedicated to manage the CPU data mirroring function and the automatic switchover function as well as any matrix system switching/control programming. In the event that this PC should fail, there shall be no loss of operation to the matrix switching system or camera control functions.
a. The status of the system controller components shall be graphically displayed in the Controller PC status display window on the LCD flat screen monitor. The status display shall graphically indicate the currently selected CPU and LAN switch and then indicate if a failure has occurred to the switching system CPU/Power Supply causing an automatic switchover to occur.
b. The system controller PC, LCD flat screen monitor, and PC keyboard shall be supplied by the manufacturer with EIA 19-inch rack mountable capabilities.
5. Primary and backup 12-port, 10/100BaseT Ethernet LAN switches provide a communication link between the main CPU and the system’s video input and output bays.
6. LAN and PC data communication cables that interconnect the CPU, input and output video bays, LAN switches, and the system controller PC shall be provided by the manufacturer.
1.5 SUBMITTALS
A. Submit under provisions of Section [01 33 00.]
B. Product Data:
1. Manufacturer’s data, operator and installation manuals software programs.
C. Shop Drawings; include
1. System device locations on architectural floor plans.
2. Full Schematic of system, including wiring information for all devices.
D. Closeout Submittals
1. User manual.
2. Parts list.
3. Connection diagram.
4. Installation CD.
5. Software license.
1.6 QUALITY ASSURANCE
A. Manufacturer:
1. Minimum of [10] years experience in manufacture and design of electronic security systems including sophisticated PC-based systems and digital products.
B. Manufacturer’s quality system: Registered to ISO 9001:2000 Quality Standard.
C. Installer:
1. Minimum of [5] years experience installing IP CCTV systems.
1.7 DELIVERY, STORAGE AND HANDLING
A. Comply with requirements of Section [01 60 00].
B. Deliver materials in manufacturer’s original, unopened, undamaged packaging; and unharmed original identification labels.
C. Protect store materials from environmental and temperature conditions following manufacturer’s instructions.
D. Handle and operate products and systems according to manufacturer’s instructions for installation, environmental, mechanical or electrical requirements and within thermal stress limits.
E. Ensure conformance with operating limitations according to applicable data sheet.
1.8 WARRANTY
A. Provide manufacturer’s warranty covering [3] years for CCTV products to repair and replace defective equipment.
B. Exchanges available for product failures.
1.9 MAINTENANCE
A. Make ordering of new equipment for expansions, replacements, and spare parts available to dealers and end users.
B. Provide factory direct technical support from 8:00 a.m. to 8:00 p.m. via phone or e-mail, or any time via Web.
1. Provide toll-free numbers to contact customer support.
C. Provide on-site training and on-line training via web.
PART 2 – PRODUCTS
2.1 MANUFACTURERS
A. Acceptable Manufacturer:
Americas:
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, Pennsylvania, 17601, USA
Phone: + 1 800 289 0096
Fax: +1 585 223 9180
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
www.boschsecurity.com
B. Substitutions: [Not permitted.] [Under provisions of Division 1.]
1. [All proposed substitutions must be approved by the Architect or Engineer professional.]
2. [Proposed substitutions must provide a line-by-line compliance documentation.]
**********Specifier's note: Select Divar XF based on project requirement. The Bosch Divar XF has several models based on disk storage size and the number of channels.
2.2 BOSCH LTC 8900 SERIES ALLEGIANT MATRIX/CONTROL SYSTEMS–MODULAR
A. The system shall be designed to support a satellite configuration where the main switcher/controller system can communicate with up to 256 remote combinations of matrix switchers compatible with the main switcher. The remote switchers accept video input from cameras located at their respective sites and allows minimization of the number of video and control cables required between the main control site and remote satellite sites. The main switcher/controller shall support configuration programming for a combination of video trunk lines, local cameras, and remote cameras up to a maximum of 6144 inputs.
B. The switcher/controller shall have a 6-digit camera identification mode. Where the first two digits represent the site number and the last four digits represent the camera number.
C. The switcher/controller shall allow programming and storage of up to 256 sequences which can be run independently of each other in either a forward or reverse direction and may be activated and deactivated automatically based on the time of day and the day of the week as provided by 128 programmable time activated events.
D. The switcher/controller shall incorporate SalvoSwitching® to allow synchronized video switching of up to 512 monitors.
E. The switcher/controller shall support the operation of up to 120 full-function keyboards and shall provide 64 built-in priority levels that can affect operator access to various features and functions of the system and can be changed via the manufacturer’s PC based configuration software. The system shall be programmable to allow keyboards to either always be on-line or to require a user log-on before access to the system is permitted.
F. The switcher/controller shall support up to 128 users with selectable password security and programmable user names.
G. The switcher/controller shall provide integral video loss detection.
H. The switcher/controller shall provide, but not be limited to, the following alarm handling capability:
1. Accept up to 1024 alarm contact points or logic level inputs via an alarm interface unit compatible with the manufacturer’s switcher system.
2. Respond to up to 2048 alarm inputs via commands received by the CPU’s RS-232 port from an access control system, PC, or other computing device that can be programmed to communicate using manufacturer supplied command codes.
3. Any monitor, or groups of monitors, can be set to automatically display cameras in response to alarm inputs. Alarmed video may be selectable to reset automatically or manually. If the system application requires multiple alarm mode capability, this switcher/controller shall allow these modes to be programmed within the same system using the manufacturer supplied configuration software.
4. Alarm call-up of pre-position scenes and display a programmable 16-character alarm title to designate the specific alarm condition.
I. The switcher/controller system specified, when combined with the Bosch Bilinx Data Interface Unit, shall support the bi-directional communication protocol embedded in the video signal of Bosch Dinion and AutoDome cameras. The Bilinx operation supported by the switcher/controller uses standard video cable to transmit pan/tilt control and also alarm and status messages from the cameras.
J. The switcher/controller shall provide an RS-232 interface port which may be used to externally program or control the system using the switcher manufacturer supplied control codes via a PC, access control system, or other computing device.
K. The supplied PC software, in addition to managing the data mirroring and automatic switchover functions, shall provide a configuration program in a spreadsheet format that allows programming of camera titles, timed events, system parameters, camera sequences, lockouts, video loss detection, and alarm programming.
L. All system equipment bays shall be rack mountable.
M. The switcher/controller shall support a minimum of 10,000 macros that can be programmed to run a pre-defined series of switcher related actions. It shall be possible to activate the macros from operator keyboards, timed events, alarms, power on reset, and/or via ASCII based external interface commands.
N. Electrical Specifications:
1. Input voltage level: 0.5 Vp-p to 2 Vp-p (Composite negative sync)
2. Gain: Unity ± 2% (75 Ohm terminated)
3. Video Bandwidth (-3 dB): 17 MHz
4. Frequency Response: ± 0.5 dB to 11 MHz
5. Signal-to-Noise Ratio: 70 dB at 3.58 MHz unified unweighted minimum
6. Crosstalk (at 3.58 MHz):
a. Typical: –65 dB
b. Adjacent: –45 dB (typical)
7. Hum: 60 dB below the composite 1 Vp-p video signal from 60 Hz to 6 MHz
O. Mechanical Specifications
1. All equipment bays shall be rack mountable to EIA Industry Standards.
P. Environmental Specifications
1. Temperature:
a. Operating: +4°C to +50°C (+40°F to +122°F)
b. Storage: –40°C to +60°C (–40°F to +140°F)
2. Altitude: 4500 m (15,000 ft)
3. Humidity: 0% to 95% relative, non-condensing
4. Vibration: 3 g swept sine wave, 15 Hz to 2000 Hz
5. Shock: 50 g, 11 m/s, ½ sine wave
PART 3 EXECUTION
A. EXAMINATION
1. Examine areas to receive devices and notify adverse conditions affecting installation or subsequent operation.
2. Do not begin installation until unacceptable conditions are corrected.
3. Non-compliance with security instructions may result in loss of data.
4. Ensure environmental, mechanical and electrical requirements are met.
B. PREPARATION
1. Protect devices from damage during construction.
C. INSTALLATION
1. Install devices in accordance with manufacturer's instruction at locations indicated on the floor drawings plans.
2. Perform installation with qualified service personnel.