Infinity Yvet-Wall Demonstration Walls

Infinity Classroom Items Needed

1)A digital projector

2)A TV-VCR

3)Dry-erase board & markers

4)3 tables and enough chairs for all attendees

5)The following literature for each attendee:

DS120 – Infinity® System Installation Details
DS136 – Infinity System Specifications
DS145 – Infinity System Installation Instructions

Materials Needed

Buy Locally

1)3 frames 3 5/8” x 4’ x 8’ Stud Frames

2)4 sheets 1/2” x 4’ x 8’ DensGlass Gold

3)1 box #6 x 1 1/4” S-Pt. Bugle/Wafer Head Coated Screws

4)25 pieces 2” x 12’ x 24” I.S. Closure Blocks

5)15 pieces 2” x 24” 48” I.S. Insulation Board™

6)1 tube Tremco Spectrem 1, 3, or 4 sealant

7)1 tube Dow Corning 790 or 791 sealant

8)2 bags 2” regular EPS foam

9)1 bag cement

Wet Wall Kit

10)1 roll 4” Grid Tape™

11)1 piece 10’ I.S. Track

12)2 pieces 10’ I.S. Vent Track™

13)1 - 1 gallon pail AquaFlash®

14)1 roll 6” AquaFlash Mesh

15)6 pieces 2” x 6” x 48” I.S. Starter Strip

16)4 pieces 2” x 6” x 18” I.S. Vent Assembly

17)1 - 60 lb/pail Backstop® NT - Texture

18)1 - 60 lb/pail I.S. Base™

19)40 feet 9 1/2” Detail Mesh® short rolls

20)16 feet 9 1/4” Corner Mesh

21)25 feet 48” I.S. Reinforcing Mesh™

22)1 - 20 oz tube AP Adhesive

23)1 pail of (select one) either Primus® or Genesis®

24)2 bags of (select one) either Primus DM, Genesis DM or Genesis DMS

Tools/Equipment Needed

1)Electric Drill (1/2” minimum) – 700-1000 rpm’s

2)Screw gun

3)Twister mixing paddle

4)5 empty 5-gallon pails (must be clean)

5)Clean water

6)Electric supply and an extension cord

7)Protective covering for the floor

8)Some type of tape

1a - Infinity wet wall materials list and instructions.doc1

Demonstration Walls Needed

1. WALL FRAME CONSTRUCTION (see detail attached)

Provide three (3) frames as shown in FIGURE 1. Studs should be metal, but can be wood if metal availability is a problem. Metal frames can be screwed together, welding is not necessary.

Apply 1/2” DensGlass Gold to all three frames using #6 x 1 1/4" coated bugle head or wafer head screws with Type S point installed at 8” on-center. Install the DensGlass Gold with the gold side OUT, and broken as shown in FIGURE 2.

Prepare each panel as follows prior to the WET-WALL:

PANEL #1: Leave as is with DensGlass Gold installed per FIGURE 2.

PANEL #2: Apply Backstop NT - Texture over the DensGlass Gold per FIGURE 3.

Do not return the Backstop NT - Texture into the opening.

PANEL #3: Apply 2" thick I. S. Insulation Board, I. S. Closure Blocks, I. S.

Starter Strip, etc., as per FIGURE 4, and rasp the entire panel surface.

2. WET WALL DEMONSTRATION

PANEL #1:

Indicate:1.Proper Sheathing installation.

Fastener type and spacing
Offset joints from corners of openings
No gaps greater than 3/8'
Etc.

Show:1.Grid Tape installation

2.Mix Backstop NT - Texture material

3.Spot Grid Tape with Backstop NT - Texture

4.Apply Backstop NT - Texture over entire surface of DensGlass Gold. Do not return into opening

PANEL #2:

Indicate:1.Proper Air Barrier Installation and inspection.

Show:1.Apply AquaFlash at opening. See detail attached.

2.Install Detail Mesh around the opening and along the base.

3.Install the I. S. Vent Assembly and I. S. Starter Strip at base of wall. You may need a temporary support to prevent displacement. DO NOT USE NAILS.

4.Install I. S. Vent Track™ above l. S. Starter Strip with opening located directly above I. S. Vent.

5.Install the Closure Blocks at the corners of the opening and then fill in between. The top edge of the Closure Blocks at the head of the opening needs to be notched to accept the I.S. Track.

6.Install the I. S. Insulation Board and outside corner Closure Blocks to complete the EPS installation. Vertical grooves in the insulation board should be aligned.

1a - Infinity wet wall materials list and instructions.doc1

PANEL #3:

Indicate:1.Proper EPS installation and inspection

Show:1.Slivering and rasping

2.Mixing of the I. S. Base material

3.Embed Detail Mesh at terminations

4.Embed I. S. Reinforcing Mesh in I. S. Base mixture. Show two (2) coat method

5.Double wrap the outside corner or use Corner Mesh

6.Discuss use of sealants

1a - Infinity wet wall materials list and instructions.doc1