Suggested Specification
ES System
(End Suction Pumps without Tank)
Variable Pressure
Water Pressure Booster System

JOB NAME:

LOCATION:

CONSULTING ENGINEER:

DATE:

PART I. GENERAL

1.01 Summary

Furnish and install a prefabricated ES model ______water pressure booster system as designed and manufactured by SyncroFlo.

1.02 References

A. American National Standards Institute (ANSI)

B. American Standard for Testing Materials (ASTM)

C. National Electric Code (NEC)

D. Underwriters Laboratory (UL) - Electrical Assemblies - UL 508

E. Occupational Safety and Health Administration (OSHA)

F. Food and Drug Administration (FDA)

G. National Fire Protection Association (NFPA) 70

1.03 System Description

The system shall be capable of automatically providing a minimum system pressure of _____ psig while at a flow rate from 0 to _____ GPM with a suction pressure of _____ psig minimum, _____ psig maximum. Incoming power shall be 3 phase/60 cycle/volts. Major components of this SyncroFlo ES system shall include end suction pumps, ODP motors, pilot operated regulating valves, gauge board, drip-tight shutoff valves, pressure and flow sequencing, and NEMA 1 control panel.

1.04 Submittals

A. Prior to Fabrication

Submit six copies to the Engineer for approval, including the following:

  1. Certification that the manufacturer is a UL listed control panel manufacturer
  2. Manufacturer's NRTL approval as a manufacturer of factory assembled pumping systems meeting OSHA safety standards
  3. Easily readable functional description of the proposed equipment
  4. Sequence of operation
  5. Electrical schematic showing internal and external wiring connections
  6. Test facility location, flow capacity, and all standard measurements taken
  7. Pump performance curves plotting flow, head, efficiency, and NPSH required
  8. Panel face diagram showing location of components
  9. List of job name, city, state, system type, model number, consulting engineer, and contractor of the past 30 projects that used similar components
  10. System data sheet listing all mechanical components and overall size
  11. Control panel data sheeting listing major components and pressure switch settings
  12. System warranty
  13. Detail drawings or descriptions of all components listed in section 2.01

B. Prior to Final Acceptance

  1. As-built drawings for all components and software listed above
  2. Flow test results (X-Y plot)

1.05 Manufacturer's Qualifications

A. Equipment under this section shall be furnished by a single supplier.

B. The supplier shall have the sole responsibility for proper functioning of the system and equipment supplied.

C. Equipment shall be products that the manufacturer regularly produces.

D. Manufacturer shall have in place a quality assurance program.

E. Manufacturer shall have thirty years manufacturing and pump system application experience.

F. Manufacturer shall have a facility capable of testing the specified system at design flow and system pressure. Facility shall be capable of providing suction pressure throughout the specified range.

1.06 Warranty

The SyncroFlo pumping assemblies and pressure regulating valves shall be guaranteed for one year from date of shipment against defective material and workmanship. The motors shall also be guaranteed for one year from date of shipment against burnout from any cause when equipped with the pumping system manufacturer's over-temperature protection and maintained according to instructions.

The complete pumping system shall be guaranteed in writing by the manufacturer for a period of one year from date of startup or eighteen months from shipment, whichever comes first, against defects in design, materials, or construction. Warranties and guarantees by the suppliers of various components in lieu of single-source responsibility by the manufacturer will not be accepted.

1.07 Spare Parts

Ship the following spare parts with the system: 1 pint of touchup paint, spare control power fuses, and spare light bulbs.

PART II. PRODUCTS

2.01 System Performance

A. Attributes

1. Normal Operation

The lead pump shall run continuously. Lag pumps shall be sequenced on and off by an insertion-type paddlewheel flow sensor. As a backup, lag pumps shall be sequenced on and off by the low system pressure sensor.

Automatic sequencing shall include the following features:

  1. Successive and 24-hour alternation of equal capacity pumps
  2. Pump overlap during 24-hour alternation
  3. Lag pump exerciser function
  4. Sequential pumps starts and stops
  5. Minimum run and stop delay timer for each pump
  6. Field adjustable time delay for low system pressure start signals

2. Emergency Alarms and Control

Automatic alarm sequencing shall include the following features:

  1. Sequence shifting that adjusts the pump sequence when any pump is disabled
  2. Each pump shall have a temperature relief valve
  3. Sequencing to reduce hydraulic or electric surges after power restoration or alarm reset
  4. Provide pressure sensors for low system and low suction conditions to activate the alarm system. All pumps shall stop and require manual reset.

B. Code Compliance

All packaged equipment shall be Nationally Recognized Testing Laboratory (NRTL) certified as a packaged pumping system suitable for the intended use in accordance with OSHA Federal Regulations and National Electric Code (NEC) Article 90-7. Safety certification label shall be permanently attached to pump system.

C. Factory Prefabrication

The entire booster system shall be factory prefabricated on a structural steel stand with all interconnecting piping and wiring completed and operationally tested prior to shipment. The assembled package shall also include lug type butterfly or full port ball valves for isolating pumps. Suction and discharge headers shall be stainless steel. Header piping connections shall be flanged. All discharge-side piping shall be rated for the specified maximum suction pressure plus pump shutoff pressure. Tubing for pressure switches and gauges shall be copper with brass isolation valves. The only field connections required will be to the suction and discharge headers, and the power connections at the control panel.

D. Factory Test and Certification

The factory shall certify in writing that the water pressure booster system and its component parts have undergone a complete operational electric and hydraulic flow test prior to shipment. The test shall include a SYSTEM operating test from zero to 100% design flow and suction and system pressure conditions. The certification shall include copies of the flow and pressure test data as recorded on 11" x 17" X-Y plot. The system test may be witnessed by the owner, architect, consulting engineer, or contractor by reporting intent to do so to the factory no later than 2 weeks before expected system shipment.

2.02 Components

A. Pumps

Pumps shall be constant speed, single stage, end suction design with cast iron bronze-fitted construction, equipped with sleeve mounted mechanical shaft seals and close-coupled to the motor.

B. Motors

Motor shall be high efficiency ODP with class F insulation. Motors shall be non-overloading throughout the pump's rated capacity.

Pump / Flow
(GPM) / Head
(Ft.) / Power
(HP) / Max. Speed
(RPM) / Min. Eff.
(%) / Voltage (3ø/60~)
1
2
3
4
5

C. Check Valves

Provide non-slam check valves on the discharge branch of each pump.

D. Power and Control Panel

Furnish a single compartment SyncroFlo power and control panel. Enclosure and base pan shall be corrosion resistant steel. It shall house all control components and include control power transformer with control power light, pulsating audiovisual alarm system, and other necessary controls. Include fused disconnect switches with external operating handles, magnetic starters with 3-leg overload protection, pump run lights, and hand-off-auto selector switches for each pump. All of the electrical components shall be factory wired and tested by the pump system manufacturer in accordance with the provisions of the National Electrical Code. All control wires shall be individually numbered and each component shall be labeled accordingly. All internal wiring shall be copper stranded, A.W.G. with a minimum insulation of 90o C. Pump manufacturer shall certify the complete power and control assembly with the UL mark for Industrial Control panels.

E. Programmable Controller

Provide a UL listed programmable controller to control all pump starts and stops and indicate alarm conditions. The controller shall have the following features:

  1. Nonvolatile EEPROM memory to prevent program loss due to power failure
  2. Program cartridge or loader which allows program changes to be made by the factory and sent to the field for simple loading by the operator
  3. Input and output "on" status lights for ease of monitoring
  4. Controller shall be designed for use in locations where electromagnetic noise, voltage spikes, 32 - 130o temperature, 35 - 85% humidity, and mechanical shock within the range certified by JIS 0912 exist.

F. Flow Sensor

FlowSensor shall be accurate within 1.0% of full scale and repeatable within .3%. Flow sensor shall detect flow to ½ FPS when flow rate is decreasing.

G. Instrumentation and Emergency Controls

  1. Temperature relief valve shall be mounted in the pump casing or seal bypass line for fast, accurate response.
  2. Individual 4½" ASA grade A pressure gauges for each pump, system, and suction pressures.
  3. All pressure sensors shall be control panel mounted.
  4. Pressure gauges shall be mounted on a gauge board with 5 sides enclosed, located adjacent to the control panel.
  5. Provide pressure sensors for low system pressure and low suction pressure conditions.

PART III EXECUTION

3.01 Installation

The contractor shall install the system in accordance with the manufacturer's recommendations.

  1. Include a floor drain sized according to local code. Drain shall provide emergency drainage to prevent building damage in the event of seal failure, over- temperature.
  2. Install pump system on a concrete pad at least _____" tall.
  3. Anchor pump system in accordance with system manufacturer's recommendations.
  4. Pipe temperature relief valve discharge to drain
  5. Install isolation valves on each header.
  6. Pipe pumping system bypass line with isolation valve
  7. All field anchoring, piping, and wiring shall comply with local codes.

3.02 Startup Service

The service of a factory-trained representative shall be made available on the jobsite to check installation, supervise startup, and instruct the operator.