Mounting Instructions:

ForSuzuki LTZ400/ KawasakiKFX400 / Arctic Cat DVX400Notorious Nerf Bars.

(ATV-0411)

Parts List:

1Set of Nerf Bars (Left & Right)

1Center Bar

6Strap Buckles

1Hardware Kit

Supplied Hardware Kit:

2 (A)8 x 60mm Hex Head Flange Bolts

4 (B)8 x 25mmHex Head Flange Bolts

4 (C)8 x 90mmHex Head Flange Bolts

2 (D)8 x 45mmHex Head Flange Bolts

6 (E)8mmFlat Washers

6 (F)8mm Nyloc Nuts

2 (G)1” Aluminum Spacer

Tools Required:

13mm, 14mm Socket w/ Ratchet or Wrench

Hand Held Drill w/ 3/8” Drill Bit

Sharpie

1.Remove stock bolt from the front lower motor mount (the one toward the front of your ATV and attaches the motor mount to chassis). Do the same on the opposite side of the ATV. Now slide the center bar in place starting from the brake (right) side and through to the other side of the ATV. Inset the supplied bolts (A) into the center bar, through the supplied spacers (G) and then into the frame. A drop of Loctite is preferred on the end of the bolt. Leave these bolts loose for now so the center bar can be adjusted when installing the nerf bar.

Stock Foot Peg Option:

2a.Slide the nerf bar onto center bar. Now where the nerf bar butts up to the foot peg, notice that there are two pre-drilled holes in the nerf bar and two pre-drilled holes in the foot peg,if the holes in the nerf bar do not line up with the holes in the foot peg, you may have to drill one or both of you own holes. If this is the case, adjust the nerf bar to where you would want it to be.Then c-clamp or Visegrip the nerf bar to the front face of the foot peg and mark with a center punch or marker where you will be drilling one or two holes per side. Now pull the nerf bar back off so you can drill the hole.

3a.Remove nerf bar and drill holes where you had marked with a 3/8” drill bit.

4a.Slide the nerf bar back on. Use the supplied bolts (B) to insert it through the nerf bar and the hole you drilled in the stock foot peg. Then tighten with washer (E) and nut (F).

Notorious Peg Option:

2b. Slide nerf bar onto center bar. Then line up pre-drilled holes in nerf bar to mounting holes on the front face of your Notorious Foot Pegs.

3b. Use supplied bolts (C) to insert though nerf bar, then though the Notorious Foot Pegs, and then tighten with washer (E) and nut (F). (now skip to #6)

  1. Next, one hole per nerf side will need to be drilled using 3/8 drill bit. This hole will need to be drilled in the front of the nerf bar where it slides over the center bar, this is use as a set bolt. Drill completely through the nerf and center.
  1. Use the supplied bolt (D) and insert it through the nerf bar, center knuckle, and then secure it with washer (E) followed by a nut (F).
  1. Now its time to go back through check and tighten all bolts to manufacturer’s specs.
  1. Next you need lace in your nets onto the nerf bar as shown below in diagram A. Then loop the net straps around the frame and buckle them in with the buckles provided. See diagram B below. We stress that you must run the straps with buckles on your nerf bars for your safety.

*If you have any questions on your purchase or any of our other items, please feel free to contactus at: (951)279-3861 or email us at

Diagram A / Diagram B