2013 CPT SIDE x SIDE RULES AND REGULATIONS
RACING FUEL REGULATIONS:
- The International Snowmobile Racing (ISR) fuel rules are used also for ATV.
- Only ISR approved and commercially available fuel will be allowed.
-The usage of any fuel, oil or additives containing power up grader agents is
strictly forbidden. It includes (but not limited to) alcohol, nitrates, oxygen agents,
etc.
- The following fuel testing methods could be used:
1 - Electrical conductivity
2 - Ceric nitrate reaction test
3 - Dioxin ‘’D’’ reaction test
4 - Water Solubility
5 - any other method approved by the regulation committee
TRACTION SCREW
(Including shoulder)
-
-
-
-
-
SHANK (thread)
Maximum height0,375 ’’ (3/8)
Maximum diameter 0,375 ‘’ (3/8)
Maximum hex size 0,3125 ‘’ (5/16)
Maximum sizeno. 12
Minimum sizeno. 8
Minimum length0,750 ‘’ (3/4)
MANDATORY SECURITY EQUIPMENT FOR THE DRIVER
THE FOLLOWING ITEMS ARE MANDATORY AT ALL TIMES:
- A full-face helmet approved SNELL 2005 or ECE 22.05. (The helmet must be
fastened)
- Goggles or face shield (visor);
- Adapted gloves;
- THE USAGE OF A NECK BRACE (LEATBRACE® types) IS HIGHLY AND
STRONGLY RECOMMENDED.
- We recommend the use of a fireproof Overall suit, this one must be wear over
all
other clothing
Page 1 of 5
RULES AND REGULATIONS FOR THE SIDE x SIDE
Please be advised that your Side x Side has to pass the security check-up
before being allowed to race.
Minimum mandatory Safety devices for the class Pro Stock 1000:
- Functional red kill switch;
-Good working and safe front and rear brakes;
- A protection net covering the complete opening (height and width) on the Pilot
side, with solid fastener (plastic clip refused). The squares must have a
maximum of 2 inches X 2 inches.
Mandatory:
- Your number must be installed on both sides. The digits must have for each, a
minimum of 6 inches high by 1 inch wide. The colors must be black for the
numbers on a white background.
Safety devices recommended for the class Pro Stock 1000 and mandatory
for the class Pro MOD 1000 (Thank you to Course VTT)
- Door + Net or complete Net and bars:
- Complete Height, with solid fastener (plastic clip are not accepted). The
squares must have a maximum of 2 inches X 2 inches.
- The door can be replaced by a complete side bar which protects the
pilot and/or the passenger from the possible impacts.
- If the vehicle has only one side bar, a net covering the complete height
must be installed. See image at the bottom of the page
- If the vehicle does not have a complete height net, the pilot can choose a
quick release arm-restraints device which is fixed to the safety belt. See image
at the bottom of the page
- Safety Belt (4 points minimum.)
- A stopping device of the emergency engine by red push button must be
installed in the center of the dashboard, accessible by the pilot and to the
safety crew from outside. See image at the foot of the page
- A red light lit in any time on the track installed in the center at the back.
- The brake must be in good working condition
Page 2 of 5
Pro Stock 1000 Class rules
In stock and stock based classes, no change or modification is allowed
unless specifically allowed by these rules. If these rules do not specifically
allow a change or modification, then it must be assumed that the change or
modification is not allowed.
The Side x Side must have original OEM (or factory designated
replacement) engine, frame, body, and clutches supplied by the
manufacturer for that particular model. All components must be OEM for
the model and year, or properly filed OEM replacement parts that
supersede the original OEM parts. Factory options are not allowed unless
otherwise specified.
- Tires
- Any off road commercially available tires may be used. (3 sales point
minimum) (car tire are not accepted)
- left and right tires should have the same dimensions
- the front and rear tires can be different.
- Traction screws are accepted
- Any rim with the OEM dimension can be used
- 1000 cc maximum, the engine bore and stroke may not be changed or
altered except cylinder overbore for wear or cylinder repair «cannot
exceed .020 inch».
- engine components must be OEM for the model unless otherwise
specified. May be modified internally, but engine must retain its complete
external stock appearance and dimensions. Parts identification numbers
must not be removed.
- engine components allowable for modification or replacement
* Pistons
* Piston pins
* Rings
* Valves
* Camshaft
* Gaskets
- OEM electronic box (fire) (can be reprogrammed)
- natural air aspiration engine only
-Engine:
- Chassis/Frame
- any chassis/frame/body alterations, additions or removals, which alter
stock appearance or dimensions, are not allowed. Chassis can be
repaired or reinforced
- Suspension
- the complete suspension must be used as furnished and filed by the
manufacturer. There will be no suspension options permitted. No
modification unless otherwise specified.
- any steel spring can be used
- we can limit the rebound travel, but not the compression travel
- the suspension parts can be reinforced for safety
- The distance between the center of the tire and the center of the chassis
must be the same on the left and right
Page 3 of 5
Pro Open Class rules
- The overall width of the machine (with its driver sitting) must not exceed
177.8 cm (70 inches);
- The overall length of the machine most not exceed 304.8cm (120 pouces)
- Any Side x Side type chassis and suspension can be used, No exotic materiel for the
chassis and suspension, only steel and aluminum
- Engine:
- the engine must come from an series Side x Side
- naturally air aspirated engine only
- 1000 cc maximum, Four Stroke
- engine may be modified;
- engine components allowable for modification or replacement
* Cylinders
* Heads
* Pistons
* Piston pins
* Rings
* Valves
* Camshaft
* Connecting rod
* Gaskets
* intake and exhaust manifold
- the stroke must remain stock for the series engine used.
- Ignition:
- Exhaust
- The ignition system may be modified or changed
- may be modified or changed
- no megaphone
- the maximum Decibel accepted is 98 DB/A for all class
- Carburetor or injection may be modified or replaced, any system to force the air
admission are allowed
- Fuel
- The gasoline used must be in conformity with the CPT regulation on the
gasoline (alcohol and nitro are not accepted)
- The distance between the center of the tire and the center of the
chassis must be the same on the left and right
- Suspension:
Page 4 of 5
PROTEST
Claimant: The person who fills the protest and asks for the legality of a machine.
Defendant: The person in charge of the machine suspected. (Can be the driver)
Officials: Circuit Pro Tour direction
Protest forms are available from the Circuit Pro Tour Officials.
To be valid, a protest shall be requested no more than 30 minutes after the end of the
class race. The protest must mention the specific requested part to inspect (can be a
general protest) and must clearly identify the vehicle involved. The protest must be
signed by the claimant prior submitting it to the Technical Director or the Race Director.
The protest will be accepted and processed only if the deposit above the protest, in cash
money. The protest may be rejected before any move by the Circuit Pro Tour officials if
it is deemed non-compliant or not conform. The cash deposit will be restituted to the
claimant and the protest will be closed.
If the protest is accepted by the Circuit Pro Tour officials, the request couldn’t be
cancelled until the judgment. The deposit will be kept by the officials until the final
judgment. Two different types of request can be made in a protest:
1. A deposit of $ 100.00 will be charged to claimants who wish to contest the
legality of an outside part on the machine. A part is judged outside when no
disassembly or dismantling is required.
2. A deposit of $ 500.00 will be charged to claimants who wish to contest the
legality of an internal component or to contest the general legality of the machine.
The following components are included in this inspection: the internal
components, external, aesthetic, electrical, electronic, mechanical and running.
Two different judgments can be made after the official inspection:
1. If an ATV is recognized as correct (legal, conform) by the Circuit Pro Tour
Technical Director, the deposit will be returned, less inspection and
administration fees, to the owner of the ATV (defendant). The claimant will lose
his deposit.
2. If an ATV is found not conform (illegal) by the Circuit Pro Tour Technical
Director, the person in charge of the vehicle must correct the situation (the
illegality) immediately. The machine and its driver will be disqualified. In addition,
all points of the day will be removed at (x) driver(s) who used the ATV illegal. The
deposit will be given to the person who filed the protest (claimant), without the
inspection and administration fees.
Please note that an official judgment is final.
George Samson
President
Eastern Pro Tour
Page 5 of 5