OCFD SOPs Fleet Maintenance SOP Practice Test-82 questions OKCFire.com
1. According to Fleet Maintenance SOP (OPS/005), which of the following should be turned off before backing into the rig room?
a. Lights
b. Accessories
c. A & B
d. None of the above
2. According to Fleet Maintenance SOP (OPS/017), what type of motor oil is used to lubricate the swing drive planetary of the 75' Quint?
a. 10W-40
b. 10W-30
c. White lithium grease
d. SAE 90W
3. According to Fleet Maintenance SOP (OPS/011), what is the proper wheel chock size for tank pumpers and brush pumpers?
a. 3 3/8" wide, 3 3/8" tall, 2' long
b. 10 1/4" wide, 7" tall, 8" long
c. 2" wide, 3 3/8" tall, 3 3/8' long
d. 7" wide, 8" tall, 10 1/4" long
4. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, which of the following grease points does not have a fitting for lube?
a. Spherical bearings
b. Worm gear drive
c. Waterway monitor
d. Outrigger leg slides
5. According to Fleet Maintenance SOP (OPS/016), where are Nylatron blocks located on 95' E-One platform ladders?
a. Along the length of the bottom 2 sections
b. At the tip of the bottom 2 sections
c. Along the length of the bottom 3 sections
d. At the tip of the bottom 3 sections
6. According to Fleet Maintenance SOP (OPS/007), on what days are Oxygen Cascade Systems readings taken for reporting?
a. Mondays and Wednesdays
b. Tuesdays and Thursdays
c. Mondays and Thursdays
d. Wednesdays and Fridays
7. According to Fleet Maintenance SOP (ADN/001), who is responsible for enforcing regulations and guidelines for Fleet Maintenance Operating Procedures?
a. Chief of Support Services
b. Chief of Operations
c. Fire Chief
d. Maintenance Chief
8. According to Fleet Maintenance SOP (OPS/013), which of the following methods are used by the Senior Maintenance Officer to notify stations of PM?
a. Telephone
b. Email
c. Pink Memo
d. A & B
9. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, how often is the proper grease applied to the extension cable pulley pins and cylinder slide track?
a. Weekly
b. Monthly
c. Quarterly (every 3 months)
d. Yearly
10. According to Fleet Maintenance SOP (OPS/008), at what maximum speed are Automatic tire chains engaged or disengaged?
a. 0 mph, not moving
b. 5 mph
c. 25 mph
d. 30 mph
11. According to Fleet Maintenance SOP (OPS/014), what type of motor oil is used in the power steering reservoir of Emergency One (E-One) apparatus (RL, Platforms, Engines, Telebooms, Squads, and HazMat)?
a. 5W-30
b. 5W-40
c. 10W-30
d. 10W-40
12. According to Fleet Maintenance SOP (OPS/019), in what situation should a vehicle NOT be pulled out when stuck?
a. When vehicle is lightly stuck
b. When vehicle is stuck up to a few inches
c. When vehicle is stuck up to axles
d. Vehicle should never be pulled out when stuck
13. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, how is grease applied to the waterway pipes, slip degree joint, and Nylatrol slide track?
a. Simply apply in bedded position
b. Extend ladder at 90 degree angle
c. Extend ladder at 10 degree angle
d. Extend ladder at 0 degree angle
14. According to Fleet Maintenance SOP (OPS/018), how often should section slides of rescue ladders be re-lubricated?
a. Monthly
b. Quarterly
c. Every 6 months
d. Yearly
15. According to Fleet Maintenance SOP (OPS/002), when does the duty mechanic determine if a rig should be traded out?
a. If repairs can NOT be made within 30 minutes
b. If repairs can NOT be made within 1 hour
c. If repairs can NOT be made within 2 hours
d. If repairs can NOT be made within 3 hours
16. According to Fleet Maintenance SOP (OPS/013), who is responsible for notifying Maintenance Services when a fire department vehicle becomes due for service?
a. District Officer
b. Station Officer
c. Apparatus Operator
d. Any employee
17. According to Fleet Maintenance SOP (OPS/016), where are Nylatron blocks located on 135' E-One aerial ladders?
a. Along the length of the bottom 3 sections
b. At the tip of the bottom 3 sections
c. Along the length of the bottom 2 sections
d. At the tip of the bottom 2 sections
18. According to Fleet Maintenance SOP (OPS/017), what is used to lube the outriggers of the 75' Quint?
a. LTI lube
b. LTI molly base lubricant or equivalent
c. Thermalube
d. Hyperlube
19. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, what is the grease type used on the extension cable pulley pins and cylinder slide track?
a. White Lithium Spray (WLS)
b. White Lithium Grease (WLG)
c. Multipurpose, extreme pressure grease with water resistance (EP)
d. Special lubricant having high water resistance (SGL)
20. According to Fleet Maintenance SOP (OPS/013), which of the following informational items appear on a PM Sticker?
a. Vehicle number
b. Oil type
c. Mileage
d. All of the above
21. According to Fleet Maintenance SOP (OPS/004), which of the following can appear on the same work order as the apparatus work order?
a. SCBA
b. Rescue Tools
c. K12 Saws
d. None of the above
22. According to Fleet Maintenance SOP (OPS/017), what type of lubricant is used in the handgun for 75' Quints?
a. Regular LTI lube
b. LTI molly base lubricant or equivalent
c. LTI white lithium
d. LTI white graphite
23. According to Fleet Maintenance SOP (OPS/015), how long should the preheat button be held on new E-One rescue ladders prior to starting AC generator?
a. 15 seconds
b. 30 seconds
c. 45 seconds
d. 60 seconds
24. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, how often is the proper grease applied to the worm gear drive, elevation cylinder rod ends and waterway monitor?
a. Weekly
b. Monthly
c. Quarterly (every 3 months)
d. Yearly
25. According to Fleet Maintenance SOP (OPS/005), when can an apparatus NOT operate in the rig room when adequate number of overhead doors are open?
a. When entering
b. When leaving
c. When testing pump
d. Maintenance repairs
26. According to Fleet Maintenance SOP (OPS/013), vehicle inspections stickers are required for which of the following vehicles?
a. Rescue Ladders
b. Fire Department automobiles
c. A & B
d. None, inspections are no longer required by law
27. According to Fleet Maintenance SOP (OPS/007), by what time must Oxygen Cascade System readings be called in to the Breathing Air Shop?
a. 0700
b. 0800
c. 0900
d. 0930
28. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, what is the only item on which a mineral gear oil meeting API service classifications and viscosity requirements of SAE grade 80-90 (GL)?
a. Rotation Bearing
b. Rotation Gear
c. Elevation Bearing
d. Elevation Gear
29. According to Fleet Maintenance SOP (OPS/008), what is the maximum speed when driving with tire chains?
a. 25 mph
b. 30 mph
c. 35 mph
d. 38 mph
30. According to Fleet Maintenance SOP (ADN/002), how long are approved break times for fleet maintenance employees?
a. 8 minutes
b. 10 minutes
c. 15 minutes
d. 30 minutes
31. According to Fleet Maintenance SOP (OPS/009), unless a vehicle is in danger of further damage, what vehicles are allowed to tow fire department vehicles?
a. Rescue 8
b. HazMat 5
c. Brush Pumpers
d. FD Wreckers
32. According to Fleet Maintenance SOP (OPS/002), which of the following constitutes an emergency repair?
a. 1 headlight out
b. 2 warning lights out
c. A & B
d. None of the above are emergency repairs
33. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, how often is the proper grease applied to the rotation gear and rotation gear box?
a. Weekly
b. Monthly
c. Quarterly (every 3 months)
d. Yearly
34. According to Fleet Maintenance SOP (OPS/009), how far off the roadway does a rig have to be to require a 4-wheel drive wrecker?
a. 50 feet
b. 75 feet
c. 100 feet
d. 150 feet
35. According to Fleet Maintenance SOP (OPS/005), at what rpm range should the engine be allowed to idle after the daily check?
a. 1,000 to 1,200 rpm
b. 1,200 to 1,500 rpm
c. 1,250 to 1,500 rpm
d. 1,500 to 2,000 rpm
36. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, what is the grease type used on the manual over-ride valve?
a. White Lithium Spray (WLS)
b. White Lithium Grease (WLG)
c. Multipurpose, extreme pressure grease with water resistance (EP)
d. Special lubricant having high water resistance (SGL)
37. According to Fleet Maintenance SOP (OPS/018), what type of oil is used in the double reduction unit of rescue ladders?
a. SAE 90W
b. 10W-30
c. 10W-40
d. White lithium grease
38. According to Fleet Maintenance SOP (ADN/002), who provides approval to use city equipment or to store employee vehicles on city property?
a. Maintenance Chief
b. Chief of Support Operations
c. Fire Chief
d. District Chief
39. According to Fleet Maintenance SOP (OPS/010), which of the following is true of quartz floodlights mounted on the roof of auxiliary apparatus?
a. They are made to swivel
b. They can go up and down
c. A & B
d. None of the above
40. According to Fleet Maintenance SOP (OPS/019), what should be done if a second brush pumper becomes stuck trying to assist another vehicle?
a. Use ONLY one additional brush pumper to free the vehicles
b. Use up to a maximum of 2 additional brush pumpers to free the vehicles
c. Use any amount of vehicles to free stuck vehicles
d. Call for a wrecker
41. According to Fleet Maintenance SOP (OPS/011), what is the proper color scheme for vehicles with rear dual wheels?
a. Wheels painted RED with the bead painted ALUMINUM
b. Wheels painted RED with the bead painted RED
c. Wheels painted ALUMINUM with the bead painted ALUMINUM
d. Rear duals do not require painting
42. According to Fleet Maintenance SOP (OPS/013), what is the mileage at which fire department vehicles must be serviced if the yearly requirement has not been met?
a. every 3,000 miles
b. every 3,500 miles
c. every 4,000 miles
d. every 5,000 miles
43. According to Fleet Maintenance SOP (OPS/004), which of the following are acceptable for reporting repairs not of an emergency nature?
a. Work order
b. Calling maintenance shop
c. A or B
d. Non of the above
44. According to Fleet Maintenance SOP (OPS/018), how often should hydraulic fluid on rescue ladders be checked?
a. Daily
b. Weekly
c. Monthly
d. Yearly
45. According to Fleet Maintenance SOP (OPS/011), touch-up painting applies to which of the following vehicles?
a. Automobiles
b. Trucks
c. 3/4 ton trucks
d. None of the above
46. According to Fleet Maintenance SOP (OPS/015), if the AC generator on a new E-One rescue ladder does not start on the first try, how long should the preheat button be held before attempting to restart?
a. 30 seconds
b. 20 seconds
c. 10 seconds
d. Preheat is not required
47. According to Fleet Maintenance SOP (OPS/003), who reports day emergency repairs?
a. Rig Driver
b. Station Officer
c. Any employee
d. District Officer
48. According to Fleet Maintenance SOP (OPS/016), on 135' E-One aerials, what are the Nylatron blocks, used as ladder slides between sections, made of?
a. Graphite impregnated nylon
b. Graphite impregnated Teflon
c. Nylon impregnated graphite
d. Teflon impregnated graphite
49. According to Fleet Maintenance SOP (OPS/018), how often should the double reduction unit of rescue ladders be checked?
a. Weekly
b. Monthly
c. Quarterly
d. Yearly
50. According to Fleet Maintenance SOP (OPS/009), with whom is notification of disabled vehicles made?
a. Duty Mechanic
b. District Officer
c. Maintenance Chief
d. Dispatch
51. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, what is the grease type used on outrigger leg slides, cylinder, and clevis pins?
a. White Lithium Spray (WLS)
b. White Lithium Grease (WLG)
c. Multipurpose, extreme pressure grease with water resistance (EP)
d. Special lubricant having high water resistance (SGL)
52. According to Fleet Maintenance SOP (OPS/004), where can the correct tire pressure be found?
a. By calling the air shop
b. By calling the maintenance shop
c. By consulting operations tips SOPs
d. On the side wall of the tire
53. According to Fleet Maintenance SOP (OPS/018), what lubricant is used to re-lubricate section slides on rescue ladders?
a. Solvent
b. Extreme Pressure Grease
c. Thermalube
d. Luberplate
54. According to Fleet Maintenance SOP (OPS/016), on E-One 95' and 135' ladders, what is the grease type used on Spherical bearings?
a. White Lithium Spray (WLS)
b. White Lithium Grease (WLG)
c. Multipurpose, extreme pressure grease with water resistance (EP)
d. Special lubricant having high water resistance (SGL)
55. According to Fleet Maintenance SOP (OPS/002), where do duty mechanics work?
a. they report to the shop during normal business hours
b. they remain at their residence unless called for emergency repairs
c. they make rounds to the stations during normal business hours for non-emergency repairs
d. they report to equipment shop during normal business hours