Typical Properties of

STYLE AG1359-XF

EXTRA-FIRM DENSITY CLOSED CELL SILICONE FOAM

Description: Style AG1359-XF is an extra-firm density closed cell silicone foam material designed to be used in gasketing applications that require greater sealing capabilities than a traditional sponge rubber offers. Extra-firm density closed cell silicone foam can be utilized to seal electronic, outdoor, and lighting enclosures, while providing protection against wind, fire, and rain. Style AG1359-XF is a lightweight silicone foam and provides users with an operating temperature of -67 °F to +392 °F, with the ability to withstand +482 °F on an intermittent basis. Extra-firm density closed cell silicone foam provides users with excellent UV and ozone resistance and is often used as a material to isolate vibration or reduce shock. A UL 94 V-0 and UL 94 HF-1 listed material, Style AG1359-XF is formulated to meet the requirements of FDA regulation 21 CFR 177.2600

Atlantic Gasket’s closed cell silicone foam gasketing material is available in densities ranging from medium (AG1359-M) to an extra-firm density (AG1359-XF). Extra-firm density closed cell silicone foam can be converted into rolls ranging from as narrow as 1/4” wide, up to 36” in width. Available in Grey, the material has a smooth skin on both sides and can be manufactured to meet a wide range of standard and custom thicknesses. Atlantic Gasket has the capability to supply Style AG1359-XF without adhesive or choose from either our standard acrylic adhesive or our high temperature acrylic adhesive. Atlantic Gasket has the capacity to fabricate extra-firm density closed cell silicone foam by die-cutting or waterjet cutting to meet your requirements from the design stage through the production phase.

SPECIFICATIONS

UL 94 V-0 AND UL 94 HF-1

21 CFR 177.2600

Physical Property / Test Method / Unit of Measure / Typical Values
DENSITY / ASTM D 3574 / pcf / 27
COMPRESSION SET / ASTM D 1056 / % / <5
COMPRESSION DEFLECTION / ASTM D 1056 / psi / 22
TENSILE STRENGTH / ASTM D 412 / psi / 60
ELONGATION / ASTM D 412 / % / 60
THERMAL CONDUCTIVITY / ASTM C 518 / W/m.K / .84
FLAME SPREAD INDEX / ASTM E 162 / D 3675 / N/A / <25
SMOKE DENSITY
(TESTED AT 4 MINUTES)
(TESTED AT 1.5 MINUTES) / ASTM E 662 / N/A / 50
20
TOXIC GAS EMISSIONS RATING / SMP-800C / N/A / PASS
WATER ABSORPTION* / INTERNAL: 24 HRS. AT ROOM TEMP. / % / .20
UV RESISTANCE / SAE-J-1960 / N/A / NO DEGRADATION
Physical Property / Test Method / Unit of Measure / Typical Values
OZONE EFFECT RATING / ASTM D 1171 / N/A / 0 (NO CRACKS)
CORROSION RESISTANCE / AMS-3568 / N/A / PASS
DIELECTRIC CONSTANT / ASTM D 150 / 1 MHz / 1.58
DIELECTRIC STRENGTH / ASTM D 150 / Volts/mil / 95
DRY ARC RESISTANCE / ASTM D 495 / Seconds / 98
VOLUME RESISTIVITY / ASTM D 257 / Ohms/cm / 10
LOW TEMPERATURE FLEX
AT -67 °F (-55° C) / ASTM D 1056 / N/A / PASS
LOW TEMPERATURE
(RECOMMENDED) / SAE J-2236 / °F
°C / -67 °F
-55 °C
HIGH TEMPERATURE
(RECOMMENDED) / SAE J-2236 / °F
°C / 392 °F
200 °C
HIGH INTERMITTENT TEMPERATURE
(RECOMMENDED) / INTERNAL / °F
°C / 482 °F
250 °C

*Note – Test samples prepared have skin on all sides in accordance with ASTM D3183, as allowed per ASTM D1056

This information is furnished as a guide for selecting materials. Atlantic Gasket Corp. disclaims liability for results or use of this information. It is the customer’s responsibility to obtain and test samples when determining suitability of material for a particular application.

8/2015

· 3908 Frankford Avenue · Philadelphia, PA 19124 ·

· Telephone: 215-533-6400 · Fax: 215-533-4130 · E-mail ·

· Web page www.atlanticgasket.com ·