Ottlite LED Clip-On Booklight

Ottlite LED Clip-on booklight

DH419

Please retain these instructions for future reference. These instructions are also available in other formats.

Special warning

Important: This unit fully assembled. If battery power is desired, 3 x AAA are batteries required, not included. Alkaline or rechargeable batteries are recommended.

Please note: The important safety instructions appearing in thisinstruction sheet are not meant to cover all possible conditionsand situations that may occur. It must be understood thatcommon sense, caution, and care must be used with anyelectrical product.

General description

This LED book light can be mounted on a book edge or placed on a flat surface such as a table.

It can be powered by 3 AAA batteries (not included) or by connecting the included USB cable to your computer or to the mains using a universal USB mains adaptor (not included).

Please note: This product does not contain a charging mechanism;therefore, the USB cable is provided solely as a power sourceconnection to a USB port such as a computer. During batteryoperation, do NOT attach the USB cable to item as it will cut-off DC batterypower.

Items supplied in the box

Clip-on light
USB cable

Orientation

Hold the unit by the large rectangle, basepart. The large flat side forms the base and the battery cover.

On the top of the rectangle section is the clip. Press the clip section together to open the clip; release to close. When pressed, you will notice at the other end a plastic tab that rotates; this allows it to clip securely onto the desired item.

At the end of the rectangle, base part nearest where the arm extends out, is the round socket for when powering the unit via mains or computer is required.

Out of the rectangle protrudes the flexible arm; at the far end is the LED light. The on/off switch is a tactile dot located on the top side of the LED light.

Using the product

Remove all packaging from around the lamp andcable. Place in front of you.

Battery installation

Warning: Keep batteries away from children. If swallowed,promptly see a doctor. Do not install backwards,charge, put in fire or mix with other battery types – mayexplode or leak causing injury.

Batteries are available from RNIB. Batteries are not guaranteed.

Your LED book light can be powered by 3 AAA batteries(not included). With standard alkaline batteries, the light will operate approximately 72 hours. Light output willslowly diminish as the batteries lose energy.

To install batteries, slide the battery compartment door away from the stem while slightly depressing the door nearthe tab. Install the 3 batteries so the flat end (negative terminal) of each battery locates against a spring.

Replace the battery compartment door by laying it on the opencompartment and sliding the door towards the stem; this will engagethe tabs of the cover into the compartment.A click should be heard as itlocks into place.

Please note: Only replace batteries as a simultaneous setand do not mix with older batteries. Remove batteriesif consumed or if the light has not been in use for a longperiod of time.

Using the USB cable to power

To use the USB cable, connect the input,round connector into the socket of the LED book light. Connect the USB end to a USB power source e.g. computer USB port or your existing USB plug.

Please note: This product does not contain a charging mechanism;therefore, the USB cable is provided solely as a power sourceconnection to a USB port such as a computer. During battery operation, do NOT attach the USB cable to item as it will cut-off DC battery power.

Using the clip

To mount or attach the light, open the clip by pressing the ridged section near the stem down. Insert theclip fully over and onto the appropriate edge andverify the body of the unit is held firmly onto the book. It is suggested and recommended that an appropriate edge will be thicker than 0.25 inches and lessthan 1 inch.

To position the LED light source simply bend the stemor flex-neck as needed to point the light. Please hold thebody while adjusting the flex-neck.

Warning: Do not force the flexible stem into any extreme positions asdamage may occur.

Turn the LED light onand off by using the power switch located on the front-upper side of the light section.

Using on a table or flat surface

Set the light’s body on a steady flat surface such as a table.

To position the LED light source simply bend the stem as needed to point the light. Please hold the body of the light while adjusting the flexible neck.

Turn the LED light on and off by using the power switch located on the front-upper side of the light section

Warning: Do not force the flexible stem into any extreme positions asdamage may occur.

Safety

For indoor use only.

Do not look directly at the LEDs.

Important: Any change or modification to the product renders the warranty void.

How to contact RNIB

Phone number: 0303 123 9999

Textphone: 0845 758 5691

Web address: rnib.org.uk/shop

Postal address: RNIB Peterborough, Midgate House, Peterborough PE1 1TN

Email:

Email for international customers

Terms and conditions of sale

This product is guaranteed from manufacturing faults for 24 months from the date of purchase. If you have any issues with the product and you did not purchase directly from RNIB then please contact your retailer in the first instance.

For all returns and repairs contact RNIB first to get a returns authorisation number to help us deal efficiently with your product return.

You can request full terms and conditions from RNIB or view them online.

Registered Charity No. 226227

This product is CE marked and fully complies with all applicable EU legislation.

At the end of the product’s life you can return it to the supplier or manufacturer for free of charge disposal. This is to comply with ‘The Waste Electrical and Electronic Equipment Directive’ (WEEE).

Date:May 2017

©RNIB

RET/FORM/006.003