American Standards

8511 / electric ignition etc equip, generators, parts
851110 / Sparking Plugs
851120 / Ignition Magnetos; Magneto-dynamos; Magnetic Flywheels
851130 / Distributors; Ignition Coils
851140 / Starter Motors and Dual Purpose Starter-generators
851150 / Other Generators for Internal Combustion Engines
851180 / Electrical Ignition, Starting Equipment and Cut-outs for Internal Combustion Engine
851190 / Parts of Ignition , Starting Equipment, for Internal Combustion Engine

American Standards

ASME B107.17M-1997 (R2002), Gages,

Wrench Openings, Reference

This Standard establishes final inspection gage

sizes for wrench openings, and spark plug

wrench openings for inch and metric sizes.

This Standard does not cover every available

size, but only those most commonly

manufactured.

UL 558-1998,

Internal-Combustion-Engine-Powered

Industrial Trucks

This standard was first listed in the October 25,

1996 issue of Standards Action with the

following scope:

Covers the fire safety aspects of industrial

trucks with internal-combustion engines, such

as tractors, platform-lift trucks, fork-lift trucks,

and other specialized vehicles for industrial

use. These requirements do not cover other

possible safety aspects of such equipment.

These requirements do not cover farm or road

vehicles or automotive vehicles for highway

use. Internal-combustion engine-powered

industrial trucks covered by these requirements

are identified as follows:

Types G, D, LP, and G/LP - Trucks fueled

with gasoline (G), diesel fuel (D),

liquefied petroleum gas (LP), or either

gasoline or liquefied petroleum gas

(G/LP), having fuel, electrical, and exhaust

ANSI/SAE J2226-APR98 (RMAY00),

Internal Combustion Engines - Piston

Rings - Steel Rectangular Rings

There is no standard equivalent to this SAE

Standard. However, SAE J2226 is similar to

and represents an extension of SAE J1998

(equivalent to ISO Standard 6622/2 TR). The

SAE Standard specifies the essential

dimensional features of Type B barrel faced

steel rectangular piston rings. Only fully faced

and inlaid coated rings are included, consistent

with current U.S. practice. The requirements of

this SAE Standard apply to steel piston rings of

reciprocating internal combustion engines, up

to and including 200 mm diameter and 4.5 mm

width.

ANSI/SAE J2004-(RAPR98, Internal

Combustion Engines – Piston Rings –

Expander/Segment Oil Control Rings

ANSI/SAE J2003-(RAPR98, Internal

Combustion Engines – Piston Rings –

Coil Spring Loaded Oil Control Rings

ANSI/SAE J2002-(RAPR98, Internal

Combustion Engines – Piston Rings – Oil

Control Rings

ANSI/SAE J2001-(RAPR98, Internal

Combustion Engines – Piston Rings –

Half Keystone Rings

ANSI/SAE J2000-(RAPR98, Internal

Combustion Engines – Piston Rings –

Keystone Rings

ANSI/SAE J1999-(RAPR98, Internal

Combustion Engines – Piston Rings –

Scraper Rings

ANSI/SAE J1998-(RAPR98, Internal

Combustion Engines – Piston Rings –

Rectangular Rings with Narrow Ring

Width

ANSI/SAE J1997-(RAPR98, Internal

Combustion Engines – Piston Rings –

Rectangular Rings

ANSI/SAE J1591-APR98 (RMAY00),

Internal Combustion Engines – Piston

Rings – General Specifications

Differences, where they exist, are shown in

Appendix A. This SAE Standard specifies the

general characteristics of piston rings and

individual dimensional criteria, which are

specified as appropriate in the documents in

Section 2. This document also provides a

system for coding, designation, and marking of

piston rings. This document applies to the

manufacture of piston rings up to and including

200 mm diameter for reciprocating internal

combustion engines. It also applies to piston

rings for compressors working under similar

conditions.

ANSI/SAE J1590-APR98, Internal

Combustion Engines - Piston Rings -

Material Specifications

Differences, where they exist, are shown in

Appendix A. This SAE Standard establishes a

classification of materials intended for the

manufacture of piston rings based on

mechanical properties and the stresses that

these materials are capable of withstanding.

This document applies to the manufacture of

piston rings up to and including 200 mm

diameter for reciprocating internal combustion

engines. It also applies to piston rings for

compressors working under similar conditions.

ANSI/SAE J1589-APR98, Internal

Combustion Engines – Piston Rings –

Inspection Measuring Principles

Differences, where they exist, are shown in

Appendix A. This SAE Standard defines the

measuring principles to be used for measuring

piston rings. It applies to piston rings up to and

including 200 mm diameter for reciprocating

combustion engines. These inspection

measuring principles may also be used for

piston rings for compressors working under

analogous conditions.

ANSI/SAE J1588-APR98 (RMAY00),

Internal Combustion Engines – Piston

Rings – Vocabulary

Differences, where they exist, are shown in

Appendix A with associated rationale. This SAE

Standard defines the most commonly used

terms for piston rings. These terms designate

either types of piston rings or certain

characteristics and phenomena of piston rings.

The terms and definitions apply to piston rings

for reciprocating internal combustion engines

and compressors working under analogous

conditions.

ANSI B175.4-2006, Portable, Handheld,

Internal Combustion Engine Driven

Cut-Off Machines - Safety Requirements

This standard applies to portable, hand-held

gasoline powered-machines using a rotating

cut-off wheel that is centre mounted on and

driven by a spindle shaft, which are designed

for cutting construction materials such as

asphalt, concrete, stone, and metal.

International Standards

ISO

ISO 11565:2006

Road vehicles - Spark-plugs - Test methods and

requirements

ISO 14508:2006

Road vehicles - Spark-plugs - Terminals

ISO 16246:2005

Road vehicles - M12 x 1,25 spark-plugs with flat seating

and 14 mm hexagon and their cylinder head housing

ISO 1919:1998

Road vehicles - M14 x 1,25 spark-plugs with flat seating

and their cylinder head housings

ISO 19812:2006

Road vehicles - M10 x 1 compact spark-plugs with flat

seating and 16 mm hexagon and their cylinder head

housings

ISO 22977:2005

Road vehicles - M12 x 1,25 spark-plugs with flat seating

and 14 mm bi-hexagon and their cylinder head housing

ISO 2344:1998

Road vehicles - M14 x 1,25 spark-plugs with conical

seating and their cylinder head housings

ISO 2345:1994

Road vehicles - M18 x 1,5 spark-plugs with conical

seating and their cylinder head housing

ISO 2346:2001

Road vehicles - M14 x 1,25 compact spark-plugs with

flat seating and 19 mm hexagon and their cylinder head

housing

ISO 2347:1994

Road vehicles - M14 x 1,25 compact spark-plugs with

conical seating and their cylinder head housing

ISO 2704:1998

Road vehicles - M10 x 1 spark-plugs with flat seating

and their cylinder head housings

ISO 2705:2006

Road vehicles - M12 x 1,25 spark-plugs with flat seating

and their cylinder head housings

ISO 3412:1992

Road vehicles - Screened and waterproof spark-plugs

and their connections - Types 1A and 1B

ISO 3895:1986

Road vehicles - Screened and waterproof spark-plug

and its connection - Type 2

ISO 3896:1986

Road vehicles - Screened and waterproof spark-plug

and its connection - Type 3

ISO 8470:2006

Road vehicles - M14 x 1,25 spark-plugs with flat seating

and 16 mm hexagon and their cylinder head housings

ISO/TR 15409:2002

Road vehicles - Heat rating of spark plugs

ISO 10455:1992

Road vehicles - Dry ignition coils using rotating

high-voltage distributor

ISO 13476:1997

Road vehicles - Ignition coils - Electrical characteristics

and test methods

ISO 3553-1:1987

Road vehicles - High-tension connections for ignition

coils and distributors - Part 1: Socket-type

ISO 4024:1992

Road vehicles - Ignition coils - Low-tension cable

connections

ISO 683-15:1992

Heat-treatable steels, alloy steels and free-cutting steels

- Part 15: Valve steels for internal combustion engines

ISO 19432:2006

Building construction machinery and equipment -

Portable, hand-held, internal combustion engine driven

cut-off machines - Safety requirements and testing

IEC 88528-11:2004