Part 1 General
1.1Section Includes
A.Ultrex®Insert Double Hung and related stationary window complete with hardware, glazing, weather strip, insect screen, simulated divided lites, grilles-between-the-glass, and standard or specified anchors, trim, attachment, and accessories.
B.Ultrex®Insert Double Hung Bay window complete with hardware, glazing, weather strip, insect screen, simulated divided lites, grilles-between-the-glass, head and insulated seat board and standard or specified anchors, fiberglass reinforced ABS, trim and attachments.
1.2Related Sections
A.Section 01 33 23 – Submittal Procedures: Shop Drawings, Product Data and Samples
B.Section 01 62 00 – Product Options
C.Section 01 65 00 – Product Delivery
D.Section 01 66 00 – Storage and Handling requirements
E.Section 01 71 00 – Examination and Preparation
F.Section 01 73 00 - Execution
G.Section 01 74 00 – Cleaning and Waste Management
H.Section 01 76 00 – Protecting Installed Construction
I.Section 06 22 00 – Millwork: Wood trim other than furnished by window manufacturer
J.Section 07 92 00 – Joint Sealants: Sill sealant and perimeter caulking
K.Section 09 90 00 – Paints and Coatings: Paint and stain other than factory-applied finish
1.3References
A.American Society for Testing and Materials (ASTM):
1.C1036: Standard Specification for Flat Glass.
2.E90-09: Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements.
3.E 283: Standard Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors.
4.E 330: Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Door by Uniform Static Air Pressure Difference.
5.E 547: Standard Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential.
6.E 2190: Standard Specification for Insulating Glass Unit Performance Evaluation.
7.E 2068: Standard Test Method to Determine the Operating and Breakaway Forces of Sliding Windows and Doors.
8.F2090-17: Standard Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms.
B.Insulating Glass Manufacturer’s Alliance/Insulating Glass Certification Council (IGMA/IGCC)
C.American Architectural Manufacturer’s Association/Window and Door Manufacturer’s Association/Canadian Standards Association (AAMA/WDMA/CSA):
1.AAMA/WDMA/CSA 101/I.S.2/A440-11:NAFS- North American Fenestration Standard/Specification for windows, doors, and skylights.
2.AAMA/WDMA/CSA 101/I.S.2/A440-08: NAFS - North American Fenestration Standard/Specification for windows, doors, and skylights.
3.AAMA/WDMA/CSA 101/I.S.2/A440-05: Standard/Specification for windows and unit skylights.
D.Window and Door Manufacturer’s Association (WDMA): Hallmark Certification Program.
E.American Architectural Manufacturer’s Association (AAMA): 624-10: Voluntary Specification, Performance Requirements and Test Procedures for Organic Coatings on Fiber Reinforced Thermoset Profiles.
F.National Fenestration Rating Council (NFRC):
1.100: Procedures for Determining Fenestration Product U-factors
2.200: Procedure for Determining Fenestration Product Solar Heat Gain Coefficients and Visible Transmittance at Normal Incidence
1.4System Description
A.Design and Performance Requirements:
Product / Air Testedto psf / Water Tested
to psf / Design
Pressure
(DP) / Certifiaction Rating / Max
Overall Width / Max
Overall Height
in / mm / in / mm
Fiberglass Insert Double Hung (NINDH) / 1.57 / 4.6 / 30 / LC-PG30-H / 48 / (1219) / 96 / (2438)
Fiberglass Insert Double Hung (NINDH) / 1.57 / 3.76 / 25 / LC-PG25-D / 54 / (1372) / 85 / (2159)
Fiberglass Insert Double Hung Picture
(NINDP) / 1.57 / 4.5 / 30 / LC-PG30-FW / 72 / (1829) / 72 / (1829)
1.57 / 4.5 / 30 / LC-PG30-FW / 60 / (1524) / 74 3/4 / (1899)
1.57 / 4.5 / 25 / LC-PG25-FW / 74 7/8 / (1902) / 74 3/4 / (1899)
1.5Submittals
A.Shop Drawings: Submit shop drawings under provision of Section 01 33 23.
B.Product Data: Submit catalog data under provision of Section 01 33 23.
C.Samples:
1.Submit corner section under provision of section 01 33 23.
2.Include glazing system, quality of construction, and specified finish.
D.Quality Control Submittals: Certificates: submit manufacturer’s certification indicating compliance with specified performance and design requirement under provision of section 01 33 23.
1.6Quality Assurance
A.Code Requirements: consult local code for IBC [International Building Code] and IRC [International Residential Code] adoption year and pertinent revisions for information on:
1.Egress, emergency escape and rescue requirements
2.Basement window requirements
3.Windows fall prevention and/or window opening control device requirements.
1.7Delivery
A.Comply with provisions of Section 01 65 00
B.Deliver in original packaging and protect from weather.
1.8Storage and Handling
A.Store window units in an upright position in a clean and dry storage area above ground to protect from weather under provision of Section 0166 00.
1.9Warranty
A.Windows shall be warranted to be free from defects in manufacturing, materials, and workmanship for a period of ten (10) years from purchase date.
B.Insulating glass shall be warranted against visible obstruction through the glass caused by a failure of the insulating glass air seal for a period of twenty (20) years from the date of the original purchase.
2
Part 2 Products
2.1Manufactured Units
A.Description: Factory-assembledUltrex®. Infinity Insert Double Hung window and related picture units as manufactured by Infinity Windows & Door, Roanoke, Virginia
B.Description: Factory-assembledUltrex®. Infinity Double Hung bay unit as manufactured by Infinity Windows & Doors, Roanoke, Virginia
1.Configurations: 30 and 45 degree bay
2.2Frame Description
A.Ultrex®, a fiberglass pultrusion. Exterior and Interior 0.075” (2mm) thick.
B.Frame thickness: 7/8” (22mm) head jamb and composite side jamb, 25/32” (20mm) sill with 8 degree bevel
C.Frame width: 3 ¼” (83mm)
2.3Sash Description
A.Ultrex®, a fiberglass pultrusion. Exterior and Interior 0.075” 92mm) thick for operating units and 0.080” (2mm) thick for picture units.
B.Composite sash thickness: 1-3/8” (35mm) for operating units,
C.Operable sash tilt to interior for cleaning and removal
D.Cottage Style: Top sash ratio between 1/3 and 1/2
E.Oriel Sash: Top sash ratio between 1/2 and 2/3
2.4Head/Seat Board: for use with bay assemblies
A.Factory-installed interior head and seat board: bare pine, oak
B.Insulated seat board with white or beige exterior aluminum skin
C.Bay Cable Support
D.Bay jambs available from 4 9/16” – 8 9/16”
2.5Glazing
A.Select quality complying with ASTM C 1036. Insulating glass SIGMA/IGCC when tested in accordance with ASTM E 2190. STC/OITC ratings are tested to the stated performance level in accordance with ASTM E 90-09.
B.Glazing Method: 11/16” (18mm) Insulating glass – Altitude adjusted
C.Glass Type: Low E1,Low E2,Low E3,Low E3/ERS with Air or Argon Gas, Tempered, Tempered Obscure, Obscure, Laminate
D.Decorative glass options include Glue Chip, Rain, Reed, Narrow Reed, Frost
1.Decorative glass is not available with Low E1,Low E3/ERS, STC/OITC, or Laminate
2.Rain, Reed, and Narrow Reed not available with SDL
3.SDL available with Frost, annealed or tempered glass
4.SDL available with Glue Chip, tempered glass required
E.Glazing Seal: Silicone bedding on interior, silicone bedding on exterior
F.Glazing Options: STC/OITC upgrade, Laminate upgrade
2.6Finish
A.Exterior: Ultrex with a cross-head extruded acrylic organic coating system. Meets AAMA 624-10 requirements.
1.Exterior Colors: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Bahama Brown, Ebony
B.Interior: Ultrex with a cross-head extruded acrylic organic coating system. Meets AAMA 624-10 and 00022716 requirements.
1.Interior Color: Stone White or Sierra. Optional stainable non-wood interior wrap: EverWood™
2.7Hardware
A.Balance system: Coil spring block and tackle with nylon cord and fiber filled nylon clutch
B.Lock: zinc die-cast lock and keeper
1.Color: White, Satin Taupe, Sierra, Brass, Satin Nickel, Oil Rubbed Bronze, Antique Brass, Brushed Chrome
2.Extended Sizes: two locks
C.Lift
1.Color: White, Satin Taupe, Sierra, Brass, Satin Nickel, Oil Rubbed Bronze, Antique Brass, Brushed Chrome
2.Extended Sizes: two lifts
D.Sash Hanger: fixed upper sash only
1.Color: White, Beige
E.Factory Installed Window Opening Control Device for operating units per ASTM F2090-17: A system consisting of an acetal lever housed in an acetal shell on each stile of the top sash
1.Available on all sizes
2.Color: White, Beige
2.8Weather Strip
A.Jamb: Foam filled bulb with flexible TPE skin, to match interior color
B.Parting Stop: PVC with flexible hinged seal to match interior color
C.Bottom Sash: Beige, “V” shaped profile, vinyl foam filled with flexible TPE skin
D.Check Rail: PVC with flexible hinged wand seal. Color: Beige
E.Stationary Units: Continuous, foam weather strip at perimeter of sash. Color: Gray
2.9Insect Screen
A.Factory-installed (removable): half screen or full screen
1.Standard screen mesh material: 18 x 16: Charcoal Fiberglass
2.Optional screen mesh material: 20 x 20 mesh: Charcoal High Transparency Fiberglass
B.Frame Color: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Bahama Brown, Ebony
2.10Simulated Divides Lites (SDL):
A.7/8” (22mm) or 1 1/8” (29mm) wide with internal aluminum spacer bars
B.Interior bar: ABS (Acrylonitrile Butadiene Styrene) or cPVC (Cellular Polyvinyl Chloride), finish to match interior color
C.Exterior bar: Ultrex, finish to match exterior color
D.Lite Cuts or Patterns:
1.Rectangle
2.Cottage Style/Oriel Style
3.Prairie cut
4.Check rail
2.11 SDL Simulated Rail:
A.2-11/32” (30mm) wide with internal aluminum spacer bars
B.Interior bar: ABS (Acrylonitrile Butadiene Styrene) or cPVC (Cellular Polyvinyl Chloride), finish to match interior color
C.Exterior bar: Ultrex, finish to match exterior color
D.Lite Cuts or Patterns: Horizontal simulated rail in standard center or customer specified location with 7/8” (22mm) or 1 1/8” (29mm) wide bar above, below or both in patterns of:
1.Equal Rectangle
2.Prairie cut
2.12Grilles-Between-the–Glass (GBG)
A.23/32” (18mm) or 1” (25mm) contoured aluminum bar
B.Exterior Finish: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Bahama Brown, Ebony
C.Interior Finish: Stone White, Satin Taupe, Sierra, Bronze
D.Lite Cuts or Patterns:
1.Equal Rectangle Lite
2.Prairie cut
3.Cottage / Oriel
4.Check rail
2.13Accessories and Trim
A.Installation Accessories: Package of installation hardware for operable units consisting of:
1.Six #8 x 2” Torx® truss head installation screws
2.Six jamb hole plugs
3.One sash lift (two sash lifts on extended sizes)
4.Two #7 x ¾” Phillips flat head screws (for sash lift) (Four screws on extended sizes)
5.Keeper pile weather strip (EverWood™ only) (two weather strip on extended sizes)
6.EverWood™ test strip (EverWood™ only)
7.Paint and Stain Instructions (EverWood™ only)
B.Installation Accessories: Package of installation hardware for Picture/Transom units consisting of:
1.Twelve #8 x2” Torx®trusshead installation screws
2.EverWood™ test strip (EverWood™ only)
3.Paint and Stain Instruction (EverWood™ only)
C.Sill Installation Filler
1.108’ lengths
D.Mulling Accessories
1.Exterior mull cover
2.Mull post
3.Interior mull cover
4.Shipping bracket assembly
5.#10 x 1 1/8” screws
6.Foam block kit
E.Panning Accessories (Fiberglass Reinforced ABS)
1.Frame expander
2.Color: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Ebony or Bahama Brown
F.Aluminum Extrusions
1.Coil panning
2.Color: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Ebony, Bahama Brown
G.Exterior Accessories
1.Field applied, fiberglass reinforced ABS, Insert BMC or Flange
2.Color: Stone White, Sierra, Pebble Gray, Bronze, Cashmere, Ebony, Bahama Brown
3
Part 3 Execution
3.1Examination
A.Verification of Condition: Before installation, verify openings are plumb, square and of proper dimensions as required in Section 01 71 00. Report frame defects or unsuitable conditions to the General Contractor before proceeding,
B.Acceptance of Condition: Beginning installation confirms acceptance of existing conditions.
3.2Installation
A.Comply with Section 01 73 00.
B.Assemble and install window/door unit(s) according to manufacturer’s instruction and reviewed shop drawing.
C.Install sealant and related backing materials at perimeter of unit or assembly in accordance with Section 07 92 00 Joint Sealants.
D.Install accessory items as required.
3.3Field Quality Control
A.Remove visible labels and adhesive residue according to manufacturer’s instruction.
B.Unless otherwise specified, air leakage resistance tests shall be conducted at a uniform static pressure of 75 Pa (~1.57 psf). The maximum allowable rate of air leakage shall not exceed 2.3 L/sm2 (~0.45 cfm/ft2).
C.Unless otherwise specified, water penetration resistance testing shall be conducted per AAMA 502 and ASTM E1105 at 2/3 of the fenestration products design pressure (DP) rating using “Procedure B” – cyclic static air pressure difference.Water penetration shall be defined in accordance with the test method(s) applied.
3.4Cleaning
A.Remove visible labels and adhesive residue according to manufacturer’s instruction.
B.Leave windows and glass in a clean condition. Final cleaning as required in Section 01 74 00.
3.5Protecting Installed Construction
A.Comply with Section 07 76 00.
B.Protecting windows from damage by chemicals, solvents, paint or other construction operations that may cause damage.
End of Section
Doc. 67287 Rev. 12/18/2017 Section 08 54 13 ~ 1 ~ Infinity Insert Double Hung
CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 10/31/2018 2:34 AM