SINGLE UNIFORM TYPE INSPECTION (SUTI) REPORT
FOR VEHICLES OF CATEGORY MA, MB AND MC
MAKE: / MODEL / CATEGORYENGINE No. / VIN:
ADR 2/01 – DOOR LATCHES AND HINGES.
CLAUSE NO / FEATURE / Compliance / SSR NOA 5.1.2 / Are there two latch positions? / Y N NA
A 5.1.3 / Do all sliding doors have an intermediate latch position?
If No:
Does the sliding door automatically move away to a partially open position?
If Yes:
Is the partially-opened position readily apparent to the occupants of the vehicle? / Y N NA
Y N NA
Y N NA
A 5.1.4 / Are the latches designed in such a way as to prevent the doors opening accidentally? / Y N NA
A 5.1.5 / For Hinged Side Doors:
Are hinges mounted at the leading edge of the door?
For Double Doors:
Are hinges fitted to the leading edge of the door which opens first? / Y N NA
Y N NA
7 / If ECE Approved:
/ #
ADR 3/03 – SEATS AND SEAT ANCHORAGES
CLAUSE NO / FEATURE / Compliance / SSR NO5.2 / Is there child restraint anchorages located in the seat backs?
Are these anchorages more than 100mm below the top of seat back?
*Note: for all other requirement such as locations and accessibility please refer to ADR34/01. / Y N NA
Y N NA
A2.7 / Can any of the seats be moved or rotated for easy access of occupants to rear seating positions? (Displacement System) / Y N NA
A5.1.1 / Do all adjustment and displacement systems have an automatic locking system?
(Not applicable to arm rests unless they are likely to increase the risk of occupant injury). / Y N NA
ADR 3/03 – SEATS AND SEAT ANCHORAGES (Cont.)
A5.1.2 / Is the locking control for seats mentioned in CL 2.7 fitted to the outside of the seat close to the door?Is the locking control easily accessible to the occupant directly behind the seat concerned ? / Y N NA
Y N NA
A5.1.3 / Is the area of the rear part of the seat back above 635mm above the H point padded? / Y N NA
A5.1.4 / Are there no sharp edges or projections on the rear of any seats in front of an occupant? / Y N NA
A5.2.1 / Are the seats firmly attached to the vehicle? / Y N NA
A5.2.3 / Are all adjustable seat backs lockable in all positions provided? / Y N NA
A5.2.4 / Are all seats that can be tipped forward lock back automatically into their normal position? / Y N NA
A5.3.1 / Are head restraints fitted to all outboard front seats? (Only applicable to vehicles with a GVM under 3500kg). / Y N NA
A5.4.1 / Does the presence of the head restraint not represent an additional danger to vehicle occupants (sharp edges or roughness)? / Y N NA
A5.4.2 / Is the front and rear parts of the headrest padded? / Y N NA
A5.5 / Are head rests adjustable?
If No:
Is the height no less than 840mm for front seats?
Is the height no less than 790mm for all other seats?
If Yes:
Is the height in the lowest position no less than 840mm for front seats?
Is the height in the lowest position no less than 790mm for other seats?
*Note: Measured from the top of the seat base to the top of the headrest. / Y N NA
Y N NA
Y N NA
Y N NA
Y N NA
A5.10 / Does the head restrain have a padded area at least 85mm each side of the vertical median plane of the seat? / Y N NA
7.1 / If ECE Approved:
/ #
ADR 4/04 – SEATBELTS
CLAUSE NO / FEATURE / Compliance / SSR NO5.3 / Is there no upper torso restraint for any side facing seat? / Y N NA
6.2.1.1 / No part of the ridged sections of the safety belt have sharp edges that may cause wear or breakage due to chafing? / Y N NA
6.2.1.2 / Are all parts protected against corrosion? / Y N NA
6.2.1.4 / No rigid part made of plastic of the safety belt assemblies is installed so they are able to become trapped in a moveable seat or a door? / Y N NA
6.2.2.1 / A) Is the buckle designed that is cannot be used incorrectly?
B) Is the buckle prevented of being left in the partially–closed position? / Y N NA
Y N NA
ADR 4/04 – SEATBELTS (Cont.)
6.2.2.2 / A) Is it not possible to release the buckle inadvertently? (if no then function is satisfactory).B) Is the buckle easy to use, can it be released with one hand in one movement?
C) Is the buckle released by a button or similar device?
D) Is the colour of the release button red?
E) Does the button have sufficient size for the release operation? (For button dimensions please refer to clause). / Y N NA
Y N NA
Y N NA
Y N NA
Y N NA
6.2.3.1 / A) Does the belt adjust automatically after being fitted by the wearer?
B) For manual adjusting seatbelts, is the adjustment readily accessible by the wearer and adjustable with one hand? / Y N NA
Y N NA
7.7.3 / Does any free end of any strap extend sufficiently far enough beyond the adjusting device to allow for slip? / Y N NA
8.1.8 / If there is an airbag in front of the seatbelt, is there a warning label that is conspicuously visible to a person installing a child restraint?
*Not required if vehicle is fitted with a mechanism that automatically senses the presence of a child restraint.
*Note : If ADR 73/00 is NOT APPLICABLE, an example of the pictogram required, colours are to be as described.
IF ADR 73/00 is APPLICABLE either below are acceptable. For requirements refer to page 27 (ADR73/00) of inspection sheet.
/ Y N NA
8.1.9 / If the answer to Cl8.1.8 is no, is the vehicle fitted with a mechanism that automatically senses the presence of a rearward facing child restraint?
Does it ensure the airbag will not be deployed? / Y N NA
Y N NA
ADR 4/04 – SEATBELTS (Cont.)
Annex 16 / Are three point retractor lap sash seat belts fitted on all outboard seating positions? / Y N NAAnnex 16 / Are three point retractor lap sash seat belts fitted on all centre seating positions? / Y N NA
Annex 16 / Are all seat belts marked Ar4m or Ar4Nm?
If “NO” please record markings:
…………………………………………………………
……………………………………………………………………………………………. / Y N NA
SE Verification / For any two seating position, identify: / (1) / (2)
(1) location
(2) mfr name/trade mark # / Y N NA
(3) date of manufacture M/Y(not required if ECE) / Y N NA
(4) identification code # / Y N NA
(5) AS2596 Lic no: / #
ECE Approval marking / #
ADR 5/05 – ANCHORAGES FOR SEATBELTS
CLAUSE NO / FEATURE / COMPLIANCE / SSR NO5.2.1.1 / A) Are there seat belt anchorages for all seating positions?
B) Are the anchorages for front outboard seating positions suitable for a seatbelt with a retractor (N/A to vehicles equipped with other types of belts eg: 4 point harness type)? / Y N NA
Y N NA
5.3 / Is there no upper torso anchorage for any side facing seat? / Y N NA
5.4.1.1 / Are the anchorages located in the vehicle body or seat structure? / Y N NA
13 / If ECE Approved: / #
ADR 8/01 – SAFETY GLAZING MATERIAL
/ CLAUSE NO / FEATURE / COMPLIANCE / SSR NO /ADR8/00 is an acceptable prior Rule. Please refer to the ADR’s for guidance.
7.2
Part 8 / Is transparent material other than glass used in the vehicle?
Is all glazing suitably marked ?
AS/NZS, JIS, ANSI, ECE, BS, NZ
If YES, please note the location and markings:
……………………………………………………………………………………………
…………………………………………………………………………………………… / Y N NA
Y N NA
7.3 / Windscreen glass marked as being laminated? / Y N NA
7.4 / Is all glazing suitably marked with a relevant standard?
Is the marking visible while the glazing is installed in the vehicle? / Y N NA
Y N NA
.4 / Glazing standard and/or ECE Approval No. (Record all markings on glass)
(1) Windscreen?
………………………………………………………………………………………….
…………………………………………………………………………………………..
(2) Driver’s side Window?
………………………………………………………………………………………….
………………………………………………………………………………………….
(3) Rear screen?
……………………………………………………………………………………………
…………………………………………………………………………………………… / #
ADR 10/02 – STEERING COLUMN
CLAUSE NO / FEATUREIf a vehicle meets the requirements of ADR 73/… by using a steering
column mounted inflatable supplementary restraint system, the vehicle
shall be exempt from the requirements of this rule. / COMPLIANCE / SSR NO
7 / If ECE Approved:
/ #
ADR 11/00 – INTERNAL SUN VISORS
CLAUSE NO / FEATURE / COMPLIANCE / SSR NO11.2.1
/Do mountings have a rigid material edge with a radius of more than 3mm?
/ Y N NA11.2.2
/Is a mirror fitted to sun visor?
Is the thickness of energy absorbing material around edge of the mirror, at least 1.5mm?
/ Y N NAY N NA
11.3.2 / Is the sun visor fitted with energy absorbing materials on both sides? / Y N NA
1.4
/ If ECE Approved: / #ADR 13/00 – INSTALLATION OF LIGHTS & LIGHT SIGNALLING DEVICES
(1) If any item in column 1 is ‘E’ Marked note marking in Column 2.(2) Audit at least 2 items for each of Columns 3 to 9 inclusive, Circle non-compliances, otherwise tick.
(3) Indicate compliance status for table at end in space provided.
FEATURES
(1) LAMP / (2) ECE Approval (#) /
(3) Component (#) / (3) HEIGHT (#) / (4) DISTANCE APART / (5) DISTANCE FROM EDGE / (6)
COMBINED?
ADR / CLAUSE NO. OF ADR 13 / MAX / MIN / (#) / (#)
(46) / Main beam
(Cl A.6.1.)&(A.6.1.4) / Dipped beam
(13)
7.3 / Driving Lamps / Orientation towards the front
(46) / Dipped Beam
(Cl A.6.2.) / 1200 / 500 / 400
(50) / Front Fog Lamp
(Cl A.6.3 ) / 800 and
< Dip. beam / 250 / 400
(1) / Reversing Lamp
(Cl A.6.4 ) / 1200 / 250
(6) / Direction Indicator
Front
(Cl A.6.5) &
(A.6.5.4.2) / 1500/ / 350 / 600 / 400
ADR 13/00 – INSTALLATION OF LIGHTS & LIGHT SIGNALLING DEVICES (Cont.)
(1) LAMP / (2) ECE Approval (#) /(3) Component (#) / (3) HEIGHT (#) / (4) DISTANCE APART / (5) DISTANCE FROM EDGE / (6)
COMBINED?
(6) / Direction Indicator Rear
(Cl A.6.5 ) &
(A.6.5.4.2) / 1500/ / 350 / 600 / 400
(6) / Direction Indicator Side
(Cl A.6.5.) (A.6.5.4.2) / 1500/ / 350
(49) / Stop Lamp
(Cl A.6.7) & (A.6.7.4.1.) / 1500/ / 350 / 400
(45) / Cornering Lamp
(Cl 7.4.1) / < Dip. beam
(49) / Centre High Mounted Stop Lamp
(Cl A.6.7)
ECE R48 Approved only / <150 below bottom edge of rear screen or > 850 above ground
......
(48) / Rear Registration Plate lamp(Cl A.6.8)
(49) / Fr. Position lamp
(Cl A.6.9 ) / 1500/ / 350 / 400
(49) / Rr. Position Lamp
(Cl A.6.10. ) / 1500/
>2100 / 350 / 400
(52) / Rear Fog Lamp
(Cl A.6.11).&
(A.6.11.4.) / 1000 / 250 / ³100 FROM STOP
Parking Lamp
(Cl A.6.12 ) / 1500/ / 350 / 400
(47) / Retro-reflector Rear
(Cl A.6.14) / 900 / 250 / 400
ADR 13/00 – INSTALLATION OF LIGHTS & LIGHT SIGNALLING DEVICES (Cont.)
(1) LAMP / (2) ECE Approval (#) /(3) Component (#) / (3) HEIGHT (#) / (4) DISTANCE APART / (5) DISTANCE FROM EDGE / (6)
COMBINED?
(47) / (Non-triangular) Front
(Cl A.6.16.) / 900 / 250 / 600
(A.6.16.4.1) / 400
(47) / Retro-reflector Side (+)
(Cl A.6.17) / 900 / 250
(74) / Side marker
lamps
(Cl.A.6.18) / 1500/ / 250
(76) / Day time running lamp
(Cl.6.19) / 1500 / 250 / 600
(A.6.19.4.1) / 400
(45) / Cornering lamp
Cl A.6.20 / 900 and<Dip. Beam / 250 / 400
Other
CLAUSE NO / FEATURE / COMPLIANCE / SSR
No
A.2.13 /
VISIBILITY
Are apparent surfaces of all lamps unobstructed by any parts of the vehicle (including options eg. bull-bar)? / Y N NAA.5
A.5.5.1 /
GENERAL
Are all lamps constituting a pair symmetrical? (Except reverse and rear fog lamps) / Y N NAA.5.10 / Is there no red light visible from the front and no white light (except reversing light) visible from the rear of the vehicle? / Y N NA
A.5.11 / Can all front and rear position lamps, the rear registration plate lamp, and the side marker lamps (if fitted) be only switched on and off together? / Y N NA
A.5.12 / Is it only possible to switch on the main-beam, dipped-beam and front and rear fog lamps whilst the lamps referred to in clause A.5.11 are switched on? / Y N NA
A.5.14.1 / Are no lamps (other than main-beam, dipped beam or front fog lamps) concealed? / Y N NA
A.5.14.2 / Is it possible to move a concealed lighting device into the position of use, without the aid of tools, in the event of a defect? / Y N NA
ADR 13/00 – INSTALLATION OF LIGHTS & LIGHT SIGNALLING DEVICES (Cont.)