THOMSON AIRWAYS LIMITED

FLIGHT DATA RECORDER (767-300)

BOEING 767-300 / EFFECTIVITY: OYI / A/C Reg: PH-OYI
Sectors: _ _ _ to _ _ _
and _ _ _ to _ _ _
FLIGHT DATA RECORDER
DATA ACQUISITION FLIGHT, GROUND TESTS & DATA DUMP / Date:
Part 1, Raise an entry in the ‘Special Notes To Crew’ stating:
Flight Data Recording Representative Flight
On sectors _ _ _ to _ _ _ and_ _ _ to _ _ _ , complete the Stable Cruise Data section
of the Flight Log using EICAS data (not DFDAU data/print out).
Note:
Details of the sectors will be advised by Engineering Planning and should be inserted accordingly.
Retain this form in the Technical Log until completion of Part 3.
Stamp + Signature (Technician) / Date
Part 2, On completion of the specified sectors, copy the following information from the Flight Log Post Flight Certificate and cancel the ‘Special Notes To Crew’ raised at Part 1.
OUTBOUND FLIGHT
Outbound Flight Number: / Date: / Sector Time:
Landing UTC: / Take Off UTC: / Tech Log Page S/No:
Cruise Mach: / Cruise Altitude: / Cruise N1 Left Eng:
Cruise N1 Right Eng: / Cruise CAS: / Stable Cruise UTC:
INBOUND FLIGHT
Inbound Flight Number: / Date: / Sector Time:
Landing UTC: / Take Off UTC: / Tech Log Page S/No:
Cruise Mach: / Cruise Altitude: / Cruise N1 Left Eng:
Cruise N1 Right Eng: / Cruise CAS: / Stable Cruise UTC:
Signature (Flight Crew) / Date

Retain this form, with Part 1 and Part 2 completed, within the Technical Log until completion of Part 3.

Part 3, Ground Checks: To be carried out post Data Acquisition Flight above, in the order below.
Record all Times (UTC).
STEP / SYSTEM / TIME / SIGNATURE
1 / FDR / Apply electrical power & set the Flight Recorder Control Panel ON-NORM-TEST switch to the ON position.
2 / NAV / Using IRMP, record Lat/Long pos’n:
3 / NAV / Select the MCP Flight Director switches to ON/OFF for 10 sec each
4 / NAV / Select Left FMC transfer switch to ALTN for 10 sec
5 / NAV / Select Left EFI transfer switch to ALTN for 10 sec
6 / NAV / Select Left IRS transfer switch to ALTN for 10 sec
7 / NAV / Select Left ADC transfer switch to ALTN for 10 sec
8 / NAV / Ensure all transfer switches are returned to normal positions.
9 / NAV / Carry out Air Data computer Operational Test IAW AMM 34-12-00-715-001
10 / NAV / Carry out Marker Beacon Operational Test IAW AMM 34-32-00-715-028
11 / VHF Comms / Select VHF L, R (& C if fitted). Key each for 10 seconds using PTT switch on an unused frequency. Ref: AMM 23-12-00-705-026
Centre VHF fitted? Y/N ------
12 / HF Comms / Key each HF system independently. Ref: AMM 23-11-00-735-042
13 / Auto Flight / Carry out MCDP Ground test 12 IAW AMM 22-00-02-742-006-001.
14 / Auto Flight / Carry out MCDP Ground test 40. (All Options) IAW AMM 22-00-02-742-006-001.
15 / Yaw Damper / Switch each system OFF/ON
16 / Stab Trim / Carry out Position Indicator Test for the Stab Trim System using the Normal & Alternate Systems. Ref AMM 27-48-00-715-006
17 / Flaps / Test the Flap Alt power & drive system IAW AMM 27-51-00-735-235
18 / Slats / Test the Slat Alt power & drive system IAW AMM 27-81-00-735-277
19 / Config Warning / Carry Out Takeoff Config warning test IAW AMM 31-51-00-725-302-001
20 / Config Warning / Ensure Parking Brake is set. Set P61 Config switch to LDG for 10 sec
21 / EGPWS / Carry out EGPWS Operational Test IAW AMM 34-46-00.
22 / TCAS / On The Transponder controller select STBY, TA, TA/RA and back to STBY each for 10 seconds. Carry out this operation twice.
23 / Fire Warning / Test the Engine & APU fire detection loops IAW AMM 26-11-00-715-075-003 & 26-15-00-715-001. Note: Test for 10 seconds each.
24 / Fire Warning / Carry out Wheel Well operational test IAW AMM 26-17-00-715-010. Note: Test for 10 seconds.
25 / Fire Warning / Carry out Lav smoke detector operational test IAW AMM 26-13-00-715-090. Note:Test 1 Lavatory only, for 10 seconds.
26 / Stall Warning / Carry out Stall Warning Operational test IAW AMM 27-32-00-715-004-003
27 / BARO / Select 29.92Hg on CAPT & F/O Altimeters
28 / BARO / On CAPTS & F/O EFIS control panels select 100 in DH window.
29 / EFIS / On CAPTS & F/O EFIS control panels select each mode and range for 10 sec (rotary and push button selectors) Carry out this operation twice
30 / NAV / Select 108.10 MHz on ILS Controller
31 / NAV / Select 108.00 MHz on L & R VOR Controllers
32 / NAV / ON MCP select: 250 in IAS/MACH window, 90 in HDG, +2000 in V/S, 10000 Alt, Select L NAV and V NAV
33 / EICAS / Select EICAS computer to L. Make the following selections each for 10 sec: STATUS, ENG, Pull EICAS lower display C/B and reset C/B. Pull Upper display C/B and reset C/B.
34 / EICAS / Select EICAS computer to R. Make the following selections each for 10 sec: STATUS, ENG, Pull EICAS lower display C/B and reset C/B. Pull Upper display C/B and reset C/B.
35 / FDR / Operate FDR Switch from ON to NORM.
36 / FDR / Carry out a FDR Data dump IAW Task card 31-TUI-014, certify and close supplied task card.
37 / INFO / All Systems Returned to Normal.
Stamp Signature Date

Once complete please scan this completed form and email to

FORM No: ENG/1451/TFL- Issue 0- Page 1 of 3