INTEGRATED HIGH SPEED PAN TILT CAMERA
INSTALLATION&PROGRAMMING MANUAL
(English Version)
Catalogue
Chapter 1: FORWARD
1.1 FORWARD
1.2 Appearance
1.3 Function explanation
Chapter 2 Notice proceeding of Installation
2.1 Safety Notice
2.2 Preparation of installation
2.3 Notice of installation
Chapter 3 Notice proceeding of Installation
3.1 Pedestal stand mode
3.2 Wall stand mode
Chapter 4:TECHNICAL PARAMETER
4.1 Structure
4.2 Rotation Index
4.3 Electric Index
4.4 Camera module Parameter
4.5 IR lamps Parameter
Chapter 5 OPERATION
5.1 Auto configure after Power On
5.2 Basic Function Operation
5.3 Special Function Preset
5.4screen character display
Chapter 6 OSD OPERATION
6.1 Operation Introduction
6.2 Main Menu
6.3 Second Menu I
6.4 Camera MenuⅠ
6.5 Camera MenuⅡ
6.6 Pan/Tilt Menu
6.7 Power on Mode
6.8 Privacy Zone Menu
6.9 Alarm input
6.10 Aux control
6.11 Camera Reset
6.12 wiper using
Appendix 1 Dial Switching Setting
Appendix 2 Pelco P Protocol
Appendix 3 Pelco D Protocol
Appendix 4 Troubleshooting and Resolution
Chapter 1: FORWARD
1. 1 FORWARD
This manual introduces the function, installation and operation of the integrated high speed pan tilt camera in details. Please thoroughly familiarize yourself with the information in this manual prior to installation.
This series pan tilt camera is specially designed for airport, frontier defense, customs, highway etc. It has many features: reliable, stable, airproof, waterproof, acid water proof, be able to bear of high temperature, aging, strong wind and so on. It adapt to the following hard conditions, such as high wind power, gap difference temperature conditions, high electromagnetism and thunder disturb, and all day working conditions.
This series pan tilt integrated with high speed decoder, pan tilt, shield, heater, defrost devise, wiper and so on. The optical module with a changeable focus lens which is DSP (Digital Signal Processing) camera.
Protocol P/D is used in this pan tilt cameras. It can support most popular system platforms, such as: PELCO. This manual will not explain the operation of other system if connecting with other system, please contact with the system manufacture or dealer.
1.2 Appearance
1.3 Function explanation
l 1.3.1 MAIN FUNCTION FEATURES：
● Pan tilt camera use high strength all-alloy material, it is waterproof, and be able to bear of high temperature, aging, and erosion.
● Accurate motor driving, stable operation, sensitive reaction and accurate orientation
● For indoor/outdoor use
● Support presets, auto scanning mode and preset tour
● RS-485 feed back the orientation the pan& tilt
● Baud rate: 1200/2400/4800/9600b selectable
● Pedestal and wall mount installation.
● High reliability and the internal data will not lost after power cutoff
● The pan/tilt orientation display and camera zoom display
● Built-in function menu, the function of camera and pan/tilt can be set.
● support all kind of popular integrated camera module
● Powering on state setting: can be set by in-built menu
● Several kinds of auto scanning mode, the speed can be set by built- in menu
● Functions of video freeze, WDR and BLC.
● Privacy masking function.
● IR lamps are available for better night vision effect.
● Day&night camera can be set into auto/single color/single black mode according to the circumstance’s need.
● Pattern track memory function, can record the preset transfer and all standard P/T/Z track.
● Control speed can be adjusted automatically: Pan/tilt speed and the depth of zoom lens decline proportionally
● 128 preset positions, precision error less than 0.05 0。
● Alterable auto scan speed: 10~400 /sec can be set by the in-built menu
● 8 preset tour functions, dwell time can be set to 2-60/sec
● Pan rotation: 3600 continuously rotating, with 180°auto-flipfunction for tilt
● Tilt rotation for pedestal stand mode -85 °～+35 °（0°for pan）
● Manual control speed for pan： 0.1 °～ 80 ° /s，Manual control speed for tilt： 0.1 °～ 40 ° /s
● Preset target speed:800/sec for pan, 400/sec for tilt
● Video output (PAL/NTSC) compound video output: 1.00VP-P;
● Built-in wiper, heater, fan component
● 2 alarm input
● washer-wiper linkage
● Embed in surge and lightning protector
● Meeting IP66,CE, ROHS, FCC standards
● The working temperature: -40°~ +55℃
1.3.2 Function explanation
Screen menu function (OSD)
It has screen menu function. All information of camera and pan& tilt can be displayed by menu and to set the function and parameter
Multi-camera control function
Select different camera only by mending dial switch setting, no any hardware or software needed. It supports SONY, HITACHI cameras and so on.
Proportional pan
Horizontal and tilt speed change automatically with the zoom changes. When zooming wide, the camera speeds down; then zooming narrow, the camera speeds up to catch better tracing effect.
Auto scan
Auto scan refers to the function of 3600 continuous scan the images at certain speed on the horizontal lever when keeping the pitching angle unchanged. The left and right limits can be set for continuous scan at certain speed on the horizontal lever.
AUTO FLIP
When the camera tilts downward and goes just beyond the vertical poison, the dome rotates 180°. When the dome rotates, the camera starts moving upward as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joystick control returns to normal operation. The auto flip function is useful for following a person who passes directly beneath the camera.
Preset
Any position of dome camera PTZ can be conserved. We call it preset (pre-established position). The preset can be transferred and cleaned.
Preset tour
The dome camera will transfer pre- established preset 1-8 every 10 second. It will leap over to next preset position if position in not among 1-8.
Pattern
The PTZ orientation move track of the camera can be stored, we call it pattern. The pan& tilt’s UP, DOWN, LEFT, RIGHT and the lens’ FAR, NEAR can be stored. Also we can call the presetting. This function can be used to record and simulate the operator’s operation process.
Zero test
The camera will turn to horizontal and tilt zero by preset 34 when the inevitable desynchronizing appears or the operator wants to find zero position during working process. It can reset the orientation and is convenient for operator
Low LUX (colors/ black& white swift) function
The camera automatically changes CCD LUX according to surrounding light. Color image changes to black& white one in low LUX; black& white image changes to color one in high LUX.(related to camera)
Auto focus
The camera automatically adjusts lens focus to keep clear image if auto focus mode. Manually operate FAR or NEAR focus adjustment can also adjust focus. The dome camera will recover auto focus adjustment function if operate horizontal, vertical rotation or control lens zoom.
Auto iris function
The camera automatically adjusts iris to keep normal brightness in auto iris mode. Manually operate OPEN or CLIOSE iris adjustment button can also adjust iris. The dome camera will recover auto adjustment function if operate horizontal, vertical rotation or control lens zoom.
Backlight compensation
The object will become black as the shadow if strong light appears in background. Backlight compensation function can compensate the brightness automatically to dark objects in bright light background and adjust the brightness background to avoid the image full of brightness and get clear image. Too strong backlight can make the object illegibility.
WDR (Wide Dynamic Range)
If there is quite dark and quite bright in the image, WDR can make the darkest and brightest balance to keep clear image
Privacy masking function:
The user can set the region which can not be seen by the operator. The region which has been covered will move together with the pan tilt direction, change together with the size of the image, and cover the region which need to be invisible always.
Multi kinds of way for wiper control：
By OSD menu, the wiper can be controlled by three ways: （1）single-control mode: The wiper will stop after 15 sec when receiving the control instruction. （2）Circle startup mode: When receiving the control instruction, the wiper will run for 5 sec, then stop for 15 sec. and do as like that. And it will not stop until it receives the control instruction for stop.（3）Linkage mode: when receiving the control instruction, there will be a linkage with the AUX switch, and the function of 65 preset will be carried on.
Chapter 2 Notice proceeding of Installation
2.1 Safety Notice
Aim to guarantee user to use the product correctly and avoid danger or loss of property.
Defense measure is including two parts “Warning” and “Notice” as follows:
Warning: Ignoring warning may cause death or great damage.
Notice: Ignoring notice may cause damage or loss of property.
Warning remind user to defend potential factor of causing death and great damage / Noitce remind user to defend potential factor of causing damage or loss of property.Warning
1, Completely according to the national or regional electric specification when installing and using the product.
2, Please using adapters from normal supplier.
Don’t connect multi cameras with one adaptor ( Exceeding the loading of adapter may generate excess heat or fire)
3, Turn off the power supply when connecting or dismantling the camera, never operate the dome camera with power.
4, Completely fix the speed dome camera when installing the item on wall.
5, If there is fume, fetor or noisy of the dome camera, please turn off power supply immediately and pull out the cable; And contact with our sales department right away.
6, If the camera can’t work normally, please contact with us and never dismantle it. (We are not responsible for any unauthorized modification or dismantling.
Notice
Prior to installation and use of this product, the following WARNING should be observed. This product can be only used in specified range in order to avoid any damage or danger.
l Installation and servicing should only be done by qualified service personnel;
l 2、Only use replacement parts recommended by us.
l 3、Keep the product away from anti-magnet field, make sure not to install it shook and impactive area, and never let other objects fall on the product. (ignoring the tip may cause equipment damage)
l 4、It can not be used in unqualified temperature( over 50℃ or below -40℃), high humidity ( otherwise firing may be caused)
l 5、After replacement/repair of this unit’s electronic components, conduct a resistance measurement by multi meter to avoid short circuit or turnoff.
l 6、Please use the soft cloth to clean the camera. Use neuter cleanser if bad smeared. No use the strong or corrosive cleanser avoiding scuffing.
l 7、Be cautious of moving, never press the drive parts heavily avoiding pan tilt camera troubles.
l 8 The installation bracket should be capable of supporting five times the total weight of the integrated camera.
Please thoroughly read this manual prior to installation and operation.
2.2. Preparation of Installation
1) All electric working must be accorded to latest electric, fire proof and related specification.
2) Be sure all accessories are included as packing list and application and installation way are as required. If not, please contact with supplier.
3) Be sure the product is suitable for the working environment.
2, Check installation space.
Make sure there is enough space for the product and accessory.
3 Make sure the wall can afford 4 times of the speed dome camera and accessories.
4 Preparation of cable.
Use video cable according to transmitting distance. Specification of video coaxial cable is:
1) 75 ohm resistance
2) copper core cable
3) 95% copper shield.
2.3 Safety notice of installation.
1, Prior installation, read the instruction carefully.
2, To use the power supply and voltage as the label instruction of cable, standard voltage is 18VAC, 15VDC to 24VDC are available; Best voltage is 18VAC±10%. Long time excess high or low voltage will cause damage of speed dome camera. Electric power must be kept over 50W, otherwise abnormal reset and control may occur.
3, Don’t aim the lens at high light object, otherwise CCD will abate and no image or image fuzzy.
Chapter 3 Notice proceeding of Installation
3.1 Pedestal stand mode
3.1.1 Equipment list:
The mode of camera contains following parts. Inspect each package to make sure all parts are present.
pic1：
Camera body pedestal mount Power supply box
Camera body（with Connecting cable） 1 pc
pedestal mount 1 pc
bracket hydrosphere 1 pc
fixed spanner 1 pc
manual 1 copy
Guarantee 1 copy
Certification 1 copy
Glove 1 pair
Φ8X40 bolt 4 sets
Power Supply box 1pc
3.1.2 Steps of installation:
STEP 1 Locate the floor or impending base level that can support 4 times the weight of camera. Fix the bulgy snail Φ8mm on the floor or firm surface.
：
STEP 2 fix the camera body on the floor or impending base level
Pic 3：
FLOOR OR FIRM SURFACE IMPENDING BASE LEVER
STEP 3 Put power supply, video output, RS485 control input wiring, alarm input wire through waterproof connector plugs, and connect them correspondingly to power supply, video, RS485 wiring and alarm input wire of the connecting cable.
Connect the cable refer to the following picture:
Pic 4：
Connect the cable refer to the following picture:
Step 4:
put the connecting cable with port into the pedestal and screw it with waterproof BNC plugs. Fix the pedestal and pan tilt connecting plate to the pedestal with four Φ5*10 fixed screw
pic 6：
STEP 5 screws loose the nut cover on the camera, then you will see the 8 bit dial switch. Set the protocol, bound rate, address for the camera. Screw tight the nut cover when finish setting.