ChryslerConstruction Standards

AME – PT Plants

Revision Date: 12/14/07

SECTION 09910 – PAINTING MODIFICATIONS

PART 1 - GENERAL

1.1PREAMBLE

  1. The following modifies the referenced specification section 09915, dated 04/03/01, issued by the Chrysler, AAME Building Group. Where a portion of the referenced specification is modified or deleted, the unaltered portions of the specification section shall remain in effect.
  2. Paint exposed surfaces, except where the paint schedules indicate that a surface or material is not to be painted or is to remain natural. If the paint schedules do not specifically mention an item or surface, paint the item or surface the same as similar adjacent materials or surfaces if schedules do not indicate color.

C. Related Sections, Power Train Operations Machine Tool Specification Section 9, Painting Specification. ETI-101 INSTRUCTIONS FOR THE APPLICATION AND REQUESTING OF NON-PRODUCTION RESTRICTED PART NUMBERS; ETI-102INSTRUCTIONS FOR THE APPLICATION AND REQUESTING OF NON-PRODUCTION HAZARDOUS AND POTENTIALLY HAZARDOUS MATERIAL;

ETI-103ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES FOR THE PROCUREMENT OF MACHINE TOOLS, EQUIPMENT, DIES, FIXTURES AND NON-PERISHABLE TOOLS AND SUPPLIES

D.If the OEM proposes to use solvent based paints, the supplier must identify this within the ETI-103 submission. Also, all solvent based paints must be third party tested and reported to Chrysler to be below a 0.0001% by weight of all paints for Mercury, Lead, Hexavalent Chrome and Cadmium. All testing shall be funded by the OEM. If solvent based paints are used, they must be able to be touched up at Chrysler’s site with water based paint and shall match both color and gloss. Supplier must demonstrate the application of the water based paint touch up before authorizing the shipment of the machine.

2.3COLORS

C.Chrysler paint color specification

-Safety Red, NPVP 7.5R 4/14, NPM Code 65-XXX-6130

-Safety Yellow, NPVP 3.75Y 8.5/12, NPM Code 65-XXX-6820

-Safety Green, NPVP 7.5G 4/8, NPM Code 65-XXX-5640

-Safety Blue, NPVP 2.5PB 3/10, NPM Code 65-XXX-4970

-Safety Orange, NPVP 3.75 YR 6/14 NPM Code 65-XXX-5910

-Black, NPVP N.O. 75, NPM Code 65-XXX-4730

-White, NPVP N.9.5, NPM Code 65-XXX-6540

-Machine White, NPVP 5Y 9/1 NPMCode 65-XXX-6670

-Blue (light), NPVP 2.5PB 7/6, NPM Code 65-XXX-4770

-Chrysler Blue, NPVP 10B 4/8, NPM Code 65-XXX-4825

-Stamping Blue, NPVP 7.5B 6/6, NPM Code 65-XXX-5040

-Aluminum, NPM 65-150-0150

D.The following color numbers are taken from the Chrysler Standard Colors

Exterior –

-Metal doors and frames (both sides, unless otherwise noted in Finish Schedule), and structural steel door frames Crowning Glory, Valspar 436A796 or Sherwin Williams SW1532

-Exposed metal fabrication steel frames at pedestrian doors –

-White, color matching prefabricated foam panel, or per Architect

-Steel ladders, pipe trestle supports, cooling tower grillage, steel stairs, thresholds and sill angles –

-Light gray, NPVP – 5Y 7/1, NPM Code 65-XXX-5430

-Guard posts, guard rails and posts, pipe railings and top rail of stairs –

-Safety Yellow, NPVP – 3.75Y 8.5/12, NPM Code 65-XXX-6820

-Exposed gypsum board soffits and canopies –

-White, color matching prefabricated foam panel, color as specified by Architect.

-

-Aluminum window angles and adjoining steel shall be painted to match color of aluminum windows

-Mechanical equipment, smoke vents, and fresh air intake hoods, required to be painted

-Aluminum, NPM Code 65-150-0150

-Fire protection equipment, including post indicator valves, fire hydrants and hose houses

-Safety Red, NPVP – 7.5R 4/14, NPM Code 65-XXX-6130

-Camera Poles -

-White, color as designated by Architect

Interior (Unless otherwise noted in finish schedule) -

-Exposed structural columns and wall framing, adjacent rainwater conductors, prefabricated foam panels, and concrete masonry walls, to underside of trusses or underside of floor slabs above, or underside of roof deck above, White, NPVP N.9.5, NP Code 65-XXX-6540

-Interior metal doors and frames (both sides, unless otherwise noted on Finish schedule)

-White NPVP N.9.5, NPM Code 65-XXX-6540

-Bar grating other than stair treads and landings –

-Black, NPVP-N 0.75, NPM Code 65-XXX-4730

-Steel ladders –

-Light gray, NPVP – 5Y 7/1, NPM Code 65-XXX-5430

-Steel stair stringers and support steel –

-Crowning Glory, Valspar 436A796 or Sherwin Williams SW1532

-Guardrails, handrails, and wall rails or stairs

-Safety Yellow, NPVP 3.75Y 8.5/12, NPM Code 65-XXX-6820

Refer to section 09915 for piping painting and identification.

Where NPM code is identified by “XXX”, use the appropriate intermediate number which identifies the supplier. See supplier list below:

Code 151, Sherwin Williams

Code 152, Standard Paint

Code 153, Glidden Paint

Code 154, Dupont

Code 155, PPG Industries

Powertrain Paint Colors

Machine Component / Interior Color / Paint Number / Exterior Color / Paint Number
Basic Machine / Machine White / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Electrical Panel Cabinet / Machine White
or cabinet standard if off white / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Electrical Panel Doors / Machine White or cabinet standard if off white / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Electrical Console Cabinet / Machine White or cabinet standard if off white / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Electrical Console Doors / Machine White or cabinet standard if off white / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Electrical Panel Backplane / Galvanized or
Machine White or cabinet standard if off white / NPVP 5Y 9/1 / Galvanized or
Machine White / NPVP 5Y 9/1
Push Button Box / Galvanized or
Machine White or box standard if off white / NPVP 5Y 9/1 / Galvanized or Machine White / NPVP 5Y 9/1
Push Button Doors / Machine White or box standard if off white / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Junction Box / Galvanized or Machine White
or box standard if off white / NPVP 5Y 9/1 / Galvanized or Machine White / NPVP 5Y 9/1
Junction Box Doors / Galvanized or Machine White or box standard if off white / NPVP 5Y 9/1 / Galvanized or Machine White / NPVP 5Y 9/1
Belt Guarding / Safety Orange / NPVP 3.75YR 6/14 / Safety Yellow / NPVP 3.75Y 8.5/12
Tunnel Guarding / Machine White / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Wire Mesh Guarding / Black / NPVP N 0.75 / Black / NPVP N 0.75
Wire Mesh Frames / Safety Yellow / NPVP 3.75Y 8.5/12 / Safety Yellow / NPVP 3.75Y 8.5/12
Swing Arm / Machine White / NPVP 5Y 9/1 / NPVP 5Y 9/1
Oil Mist Duct Coll. at Welds / Parent metal / Aluminum / NPM 65-XXX-0150
Conduit / Machine White or Galvanized / NPVP 5Y 9/1 / Machine White or Galvanized / NPVP 5Y 9/1
Secondary Buss Duct & Buss Plugs / Vendor Standard
Servo Motors (required for heat dissipation) / Vendor Standard / NPVP N 0.75
Tool Changers / Safety Orange / NPVP 3.75YR 6/14
Splash Guards / Safety Yellow / NPVP 3.75Y 8.5/12 / Safety Yellow / NPVP 3.75Y 8.5/12
Machine Component / Interior Color / Paint Number / Exterior Color / Paint Number
Hydraulic Cylinders / Vendor Standard / Vendor Standard
Machine Component / Interior Color / Paint Number / Exterior Color / Paint Number
Hydraulic Elements / Machine White / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Limit Switches / Vendor Standard / Vendor Standard
Electric Motors / Vendor Standard / NPVP 5Y 9/1 / Machine White / NPVP 5Y 9/1
Gage Tables / Safety Yellow / NPVP 3.75Y 8.5/12

COMMODITY MANAGEMENT PAINT SUPPLIERS

Web Site
65-151
Sherwin Williams /
65-152
Standard Paint /
65-153
Glidden (ICI Devon) /
65-155
PPG /
65-154
Dupont / (

END OF MODIFICATION

PAINTING - MODIFICATIONSSection 09910

Page 1 of 5