Honeywell H4D1F 720p TDN Rugged Minidome IP CameraGuide Specifications in CSI Format

Rev B

SECTION 282329

H.264 720p TRUE DAY/NIGHTRUGGEDINDOOR/OUTDOOR
MINIDOME IP CAMERA, H4D1F SERIES

PART 1 GENERAL

1.1SECTION INCLUDES

  1. Provide ahigh definition720p true day/nightrugged indoor/outdoor fixed minidome IP camerasystem for video surveillance, includingdesign, supply, installation, and commissioning.

1.2RELATED SECTIONS

NOTE TO SPECIFIER:Include related sections as appropriate if video surveillance system is integrated to other systems.

  1. Section 260500: Common Work Results for Electrical, for interface and coordination with building electrical systems and distribution.
  2. Section 280513: Conductors and Cables for Electronic Safety and Security, for cabling between system servers, panels, and remote devices.
  3. Section 280528: Pathways for Electronic Safety and Security, for conduit and raceway requirements.
  4. Section 282323: Video Surveillance Systems Infrastructure.
  5. Section 282329: Video Surveillance Remote Devices and Sensors.

1.3REFERENCES

  1. Reference Standards:Provide systems that meet or exceed the requirements of the following publications and organizations as applicable to the work of this Section.
  2. Canadian ICES-003.
  3. Canadian Standards Association (CSA).
  4. Conformity for Europe (CE).
  5. Electronic Industry Association (EIA).
  6. Federal Communications Commission (FCC).
  7. Joint Photographic Experts Group (JPEG).
  8. National Television Systems Committee (NTSC).
  9. Phase Alternating Line (PAL).
  10. Underwriters Laboratories Inc. (UL).

1.4SYSTEM DESCRIPTION

  1. The720p true day/night rugged minidome IP camera shall use a compact, one-piece, vandal-resistant enclosure that can be mounted directly to a ceiling or wall. An optional wall/pendant mount kit shall also be available.
  2. The 720p true day/night rugged minidome IP camerashall provide 720p (1280 × 720) resolution, a 1/4-inch progressive scan CMOS sensor with true day/night functionality, H.264 (primary stream) and H.264/MJPEG (secondary stream) compression formats, and ONVIF™Profile S support.

1.5SUBMITTALS

  1. General: Submittals shall be made in accordance with the Conditions of the Contract and Submittal ProcedureSection.
  2. Manufacturer’s Product Data:Submit manufacturer’s data sheets indicating systems and components proposed for use, including instruction manuals.
  3. Shop Drawings:Submit installation drawings, including connection diagrams for interfacing equipment, list of connected equipment, and locations for major equipment components. Shop drawings shall indicate surrounding construction as provided for the Project.
  4. Project Record Drawings:Indicate location of equipment and wiring on project record drawings.Submit an electronic version of the project record drawings not later than Substantial Completion of the Project.
  5. Operation and Maintenance Data:Submit manufacturer’s operation and maintenance data customized to the system installed.Include operator manuals.
  6. Field Tests:Submit results of field testing of every device, including date, testing personnel, retesting date (if applicable), and confirmation that every device passed field testing.
  7. Maintenance Service Agreement:Submit a sample copy of the manufacturer’s maintenance service agreement, including cost and services for a one year period for Owner’s review.Maintenance shall include, but not be limited to, labor and materials to repair the system, tests and adjustments, and regular inspections.

1.6QUALITY ASSURANCE

  1. Qualifications:Manufacturers shall have a minimum of 10 years full-time experience in manufacturing and maintaining video surveillance systems.Manufacturer shall provide toll-free technical assistance and support available 24/7. Installers shall have a minimum of 2years experience installing similar systems and shall be acceptable to the manufacturer of the video surveillance system.
  2. Regulatory Requirements:
  3. Emissions:FCC, Part 15B; EN 55022.
  4. Immunity: EN 50130-4.
  5. Safety: UL/CSA 60950-1; EN 60950-1.

1.7DELIVERY, STORAGE, AND HANDLING

  1. Packing and Shipping: Deliver products in manufacturer’s labeled packages.
  2. Storage and Protection:Store and handle products in accordance with manufacturer’s requirements, in a facility where environmental conditions are within recommended limits.

1.8PROJECT CONDITIONS

  1. Environmental Requirements: Comply with environmental requirements and recommendations of manufacturer for proper installation of products.
  2. Temperature Criteria:
  3. Operating temperatures shall be between −22°F (−30°C) and 140°F (60°C).
  4. Storage temperatures shall be between −40°F (−40°C) and 158°F (70°C).
  5. Power Requirements: Input voltage shall be 24 V AC or PoE IEEE 802.3af.

1.9WARRANTY

  1. Manufacturer’s Guarantee:Three (3)years from the manufacture date code under normal use and service for the video surveillance system.

PART 2 PRODUCTS

2.1MANUFACTURERS

  1. Specified Manufacturer: Honeywell,
  2. Accepted Part Numbers:
  3. H4D1F1.
  4. H4D1F1X.
  5. H4D1F2.
  6. H4D1F2X.
  7. H4D1F3.
  8. H4D1F3X.

2.2SYSTEM COMPONENTS

  1. Specified Product: Honeywell H4D1F720p true day/nightrugged minidome IP camera.
  2. Cabling.

2.3OPERATIONAL REQUIREMENTS

  1. The 720p true day/night rugged minidome IP camera system shall meet or exceed the following camera specifications:
  2. Image Sensor:1/4-inchCMOS.
  3. Total Pixels:1280 (H) × 720 (V).
  4. Lens Type:
  5. H4D1F1(X): True Day/Night (TDN)3.3–12 mm,varifocal auto iris, F1.6.
  6. H4D1F2(X): True Day/Night (TDN) 2.5–6 mm, varifocal auto iris, F1.2.
  7. H4D1F3(X): True Day/Night (TDN) 10–28 mm, varifocal auto iris, F1.8.
  8. Angle of View:
  9. H4D1F1(X):

1)Horizontal: 68.5° wide; 19.1° tele.

2)Vertical: 36.8° wide; 10.8° tele.

  1. H4D1F2(X):

1)Horizontal: 87.9° wide; 37.9° tele.

2)Vertical: 48.6° wide; 21.3° tele.

  1. H4D1F3(X):

1)Horizontal: 21.9° wide; 8.1° tele.

2)Vertical: 12.1° wide; 4.6° tele.

  1. Minimum Illumination: 0.25 lux color; 0.22 lux b/w @ 50 IRE, F1.6.
  2. Automatic Electronic Shutter Speed:
  3. NTSC: 1/60 to 1/24,500 seconds.
  4. PAL: 1/50 to 1/24,500 seconds.
  5. Video Output: Composite,1.0 VP-P, 75 ohms.
  6. White Balance: AWC, AWC Push, Manual.
  7. Signal-to-Noise Ratio:50 dB or higher(AGC off).
  8. Synchronization: Internal.
  1. The 720p true day/night rugged minidome IP camera system shall providetrue day/night functionality with an infrared (IR) cut filter for day mode.
  2. The 720p true day/night rugged minidome IP camera systemshall provide 3D digital noise reduction, electronic light compensation, automatic light compensation, automatic gain control, flickerless mode, and digital slow shutter.
  3. The 720p true day/night rugged minidome IP camera system shall provide fully configurable motion detection settings.
  4. The 720p true day/night rugged minidome IP camera system shall support the ONVIF Profile S specification for interoperability between network video products.
  5. The 720p true day/night rugged minidome IP camera system shall support remote firmware updates.
  6. The 720p true day/night rugged minidome IP camera system shall support HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, NTP, RTCP, FTP, ICMP, DHCP, Bonjour, IGMP, and SSH protocols.

NOTE TO SPECIFIER: Some development may be required in specific user cases to support some of these protocols in the field as they mature over time.

  1. The 720p true day/night rugged minidome IP camera system shall provide dual H.264 and/or H.264/MJPEG video streams. It shall also provide controllable frame rates and bandwidth and constant or variable bit rates.
  2. The 720p true day/night rugged minidome IP camera system shall provide Network Time Protocol (NTP) synchronization support.
  3. The 720p true day/night rugged minidome IP camera system shall support embedded date/time stamps in the video stream.
  4. The 720p true day/night rugged minidome IP camera system shall support Internet Explorer 8and 9, Mozilla Firefox®, and Google Chrome web browsers.
  5. The 720p true day/night rugged minidome IP camera system shall support input and output alarm contacts and bidirectional audio.
  6. The 720p true day/night rugged minidome IP camera system shall provide an RJ45 connection and a second video service connector (2-pin Molex).
  7. The 720p true day/night rugged minidome IP camera system shall provide 24 V AC or PoE IEEE 802.3af power input options.
  8. The 720p true day/night rugged minidome IP camera system shall have a 3-axis (pan/tilt/rotation) gimbal bracket for precise camera positioning.
  9. The 720p true day/night rugged minidome IP camera systemis designed to be surface mounted to a ceiling or wall.
  10. The 720p true day/night rugged minidome IP camera systemhousing shall consist of die cast aluminum with a cool gray powder coat finish (closest matching RAL color: RAL CODE 7047), and the bubble shall consist of impact-resistant 1.5mm-thick polycarbonate resin.

2.4SYSTEM HARDWARE

  1. The 720p true day/night rugged minidome IP camera system shall have the following mechanical specifications:
  2. Unit Dimensions (W×H): 6.1×4.6 inches (154.9×117.1 mm).
  3. Unit Weight: 3 lb (1.3 kg) camera only.
  4. Connectors:
  5. Network: RJ45 connector.
  6. Aux Video Output: 2-pin Molex connector.
  7. Power Input: Removable screw block.
  8. Alarm I/O: Removable screw block.
  9. Audio In: Removable screw block.
  10. Audio Out: Removable screw block.
  11. The 720p true day/night rugged minidome IP camera system shall have the following electrical specifications:
  12. Voltage: 24 V AC or PoE IEEE 802.3af.
  13. Power Consumption:
  14. 24 V AC: 5.0watts max.
  15. PoE: PD Type 1, Class 1.
  16. The 720p true day/night rugged minidome IP camera system shall be designed to meet the following environmental conditions:
  17. Operating temperature: −22°F (−30°C) to 140°F (60°C).
  18. Storage temperature: −40°F (−40°C) to 158°F (70°C).
  19. Relative Humidity: 10% to 100% (condensing).
  20. Ingress Protection Rating: IP66.
  21. Impact Resistance Rating: IK10.
  22. Emissions: FCC, Part 15B; EN 55022.

2.5MANUFACTURER SUPPORT

  1. Manufacturer shall provide customer service, pre-sales applications assistance, after-sales technical assistance, access to online technical support, and online training using Web conferencing.
  2. Manufacturer shall provide 24/7 technical assistance and support by means of a toll-free telephone number at no extra charge.

PART 3 EXECUTION

3.1EXAMINATION

  1. Examine site conditions prior to installation.Notify Architect and Owner in writing if unsuitable conditions are encountered.Do not start installation until site conditions are acceptable.

3.2INSTALLATION

  1. All components of the camera system shall be thoroughly tested before shipping to the project location.
  2. Camera system shall be installed, programmed, and tested in accordance with manufacturer’s instructions and recommendations.
  3. Coordinate interfaces with other products with Owner’s representative where appropriate.
  4. Provide conduit, cable, and wire for complete and reliable installation. Obtain Owner’s approval for exact location of cameras, boxes, conduit, cable, and wiring runs prior to installation.
  5. Install conduit, cable, and wire parallel and square with building lines, including raised floors areas.Do not exceed 40 percent fill in conduits.Gather and tie wires for orderly installation.
  6. Coordinate with other trades to provide proper sequencing of installation.

3.3FIELD COMMISSIONING AND CERTIFICATION

  1. Field Commissioning:Test camera system as recommended by manufacturer, including the following:
  2. Conduct complete inspection and testing of equipment, including verification of operation with connected equipment.
  3. Test devices and demonstrate operational features for Owner’s representative and authorities having jurisdiction, as applicable.
  4. Correct deficiencies until satisfactory results are obtained.
  5. Submit written copies of test results.

3.4TRAINING

  1. Conduct on-site system administrator and security/surveillance operator training in accordance with the manufacturer’s instructions and recommendations.Training shall include, but not be limited to: camera administration, provisioning, configuration, operation, and diagnostics.

END OF SECTION

28 23 29-1