1

Tool list Mechanic Agricultural Machinery

Name of the Trade for which affiliation is sought: MECHANIC AGRICULTURAL MACHINERY

Number of units in 1st shift:

Number of units in 2nd shift:

Number of units in 3rd shift:

Total units:

Sl. No. / Name of the tools Equipment & Machinery as per syllabus / Number required for Instructor &Trainees for one unit as per NCVT norms/syllabus / Total Number of Tools and equipments required for the total units affiliated and sought affiliation / Total number actually available for all the units / Indicate shortage
if any / Cost of the Tool, Equipment & Machinery / Name, Address, Tel. No. Email. Vat/TIN No. of the Supplier of General Machineries
1 / 2 / 3 / 4 / 5 / 6 / 7 / 8
Trainees Kit :
Hammer ball peen 0.75 mm. / 17
Chisel cold flat 20mm / 17
Centre punch 10 cm. / 17
Caliper outside spring 15 cm. / 17
Caliper inside spring 15 cm. English & Metric. / 17
Steel rule 15 cm. English & Metric. / 17
Screw driver 75 x 10 cm. / 17
Screw driver 30 x 1 cm. / 17
Spanner D.E. (Set of 6 BSF) / 17
Plier combination 15 cm. / 17
Hand file second cut / 17
Tools, measuring instruments General shop out fit :
Rule Steel 30 cm to read inches and mm, / 4
Dividers spring 15 cm, / 4
Prick punch 15 cm. / 4
Chisel cross cut 9 x 3 mm / 4
Chisel diamond point 9 mm / 4
Chisel half round 9 mm. / 4
Hammer ball peen 0.5 kg. / 4
Hammer ball peen 0.25 kg. / 4
Hammer copper 1 kg. with handle / 4
Hammer plastic 0.25 kgs. with handle / 4
Engineers square 15 cm blade. / 4
Scriber 15 cm. / 4
Scribing block universal. / 2
Marking out table 90 x 60 x 90 cm. / 1
Surface Plate 60 x 60 cm, / 1
Hacksaw frame adjustable for 20-30 cm blade / 4
‘V’ block pair with clamps 7.5 x 3.75 cm. / 2
Punch hollow 6.7 and 9mm set. / 2 sets
Punch letters set 3 mm. / 1 set
Punch figure set 3 mm. / 1 set
Hand vice upto 3.75 cm. / 2
Screw driver Electrician type 15 cm size. / 4
File flat 35 cm. bastard / 4
File flat 25 cm second cut / 4
File flat safe edge 25 cm smooth / 4
File flat 20 cm smooth / 4
File triangular 15 cm. second cut. / 4
File half round 40 cm. second cut. / 4
File square 39 cm. rough / 4
File square 20 cm. second cut. / 4
Drill twist S.S. 1/8” to ½” x 1/64” set. / 2 sets
Drill twist metric 3mm to 12 mm x 1mm. / 2 sets
Taps and dies complete set in Box B.A., B.S.W., B.S.F. American and Metric. / 1 set each
Rasp. / 1
H.S.S. Hand reamers, parallel 8 to 12 by 1.5 mm. / 2 sets
H.S.S. Hand reamers adjustable 11 to 12, 12 to 13, 13 to 15, 15 to 16mm. / 1 set each
H.S.S. hand reamers 3.5 to 12.5mm in steps of 1.5mm set of 12. / 1 set
H.S.S. machine reamers 3 to 19mm in steps of 1.5mm. / 1 set
Scrapper, flat 25 cm handled. / 4
Scrapper, half round 25 cm. / 4
Scrapper, triangular 25 cm. / 4
Scrapper, bearing. / 4
Chaser hard W/V 9 to 40 T.P.I. set of 11 external. / 1 set
Chaser, hand W/W 9 to 40 T.P.I. set of 11 internal. / 1 set
Set of morse socket 0-1, 1-2 and 2-3. / 2 sets
Drill indicator to read 0.25mm. / 2
Screw pitch gauge with 22 pitches from 9 to 40 BTPI. / 2
Micrometer, outside 0” – 1”. / 2
Micrometer outside 0.25 mm. / 2
Micrometer outside 50mm to 150mm with extension rod. / 1
Micrometer inside 50 to 100 mm with extension rod, / 2
Vernier caliper set 10” or 8” inside and outside, depth to read inches and mm, / 1
Safety goggles (Clear glass) / 2 pair
Hammer, planishing. / 2
Setting hammer / 2
Mallet (Wooden). / 2
Trammel 30 cm, / 1
Blow lamp. / 2
Soldering iron 120 watt. / 2
Soldering iron, copper 280 gm (Fire heated). / 2
Snip straight. / 2
Stake, hatchet. / 2
Stake grooving. / 2
Grover – 3, 4, 6mm. / 1 Each
Nose pliers 15 cm (Round and Straight). / 2 Each
Circlip Plier 15 cm. / 2
Wing compass 25 cm / 2
Pat melting / 2
Shovel / 1
Rake / 1
Poker / 1
Spanner, double ended to 10 to 25 x 1.5 mm set (BSF size) / 2 Sets
Spanner, double ended set of 12 metric sizes 8 to 32mm / 2 Sets
Spanner, double off-set double ended set of 7 W/W from 3 to 14mm. / 2 sets
Double open ended ignition spanner of B.A. 0 x 1 to 8 x 9 set of 5. / 1 set
Spanner, clyburn 15cm. / 2
Spanners, adjustable 15 cm. / 2
Spanner, ring set of 6 S.A.E. / 2 sets
Spanner, for sparking plug 10mm & 14mm. / 4 sets
Magnet spanner set. / 1 set
Double open ended, spanner American A/F, size from 8 x 10 to 25 x 1.5mm. / 1 set
Spanner, socket, set of 8 handled,
T-bar and ratchet 10, 12, 20mm. / 2 sets
Spanner, T-flax for screwing up and unscrewing inaccessible position / 1
Double open ended tappet spanner from 11 x 12 to 16 to 17. / 1 set
Drift, copper 10 x 15 1/2 mm / 2
Gun, paraffin set / 1
Gun, grease pressure. / 1
Chain and block 3050 sizes. / 1
Tray cleaning assorted sizes. / 8
Drilling machine bench 1 HP to drill upto 12mm dia. / 1
Oil can 0.12 litre. / 2
Valve spring compressor universal. / 1
Tool, valve grinding, suction type. / 6
Tool, valve grinding, screw in type. / 1
Valve seat cutting, tools complete with guides and pilot bar (All angles) / 1
Valve grinding machine. / 1
Ex-tractor stud (EZYOUT TYPE). / 1
Compression gauge to read 0 to 115 kg/Sq.cm and vacuum gauge 0 to 75cm / 1 each
Stone, carborandum 15 x 5 x 4 cm smooth and rough. / 1each
Injector testing set (Hand tester) / 1
Cylinder gauge capacity 6 to 15 cm. / 1
Ring expander and remover. / 1
Torque wrench (0 to 150 1bs.ft.) / 1
Ring groove cleaner. / 1
Torque wrench (0 to 20 kg. meter) / 1
Torque wrench (0 to 40 kg. meter) / 1
Work bench 295 x 120 x 80 cm. with 4 vices. / 4
Lockers with 8 drawers (Standard size) / 2
Metal rack 180 x 150 x 45 cm. / 1
Fuel pump. / 2
Injector pump. / 2
Dynamo and voltage regulator / 2 each
Starter motor. / 2
Carburetor (Two different types) / 2
Distributors / 2
Injectors (Two types) / 2 each
Water pump and oil pump. / 1 each
Feeler gauge / 2
Injector cleaning kit. / 2
Filing jig for adjusting the piston ring gap. / 1
Steel almirah. / 1
Desk or table, / 1
Fire extinguisher / 2
Fire buckets with stand, / 4
Ratchet brace / 1
Drill post. / 1
Twist drills for ratchet brace 6 to 20 by 1.5 cm. / 1 set
Techometer (Counting type) / 1
Brake drum spring balance belt etc. for performance testing of engine. / 1 set
Lifting jack screw type 3050 kg. / 4
Equipment puncture, in box, / 1
Spray gun set with accessories. / 1
General Installations :
Grinder with two 18 cm wheels with twist drill grinding attachment. / 1
Compressor capacity 12 c.ft. piston type with pressure gauge (For insulating of tubes etc.) / 1
Hydraulic jack HI-LIFT type, / 1
Crawler type tractor fitted with diesel engine with accessories and special tools (50 to 60 draw-bar H.P.). / 1
Wheel type tractor fitted with diesel engine with standard accessories and special tools
(30 to 40 draw-bar H.P. / 1
Trailing type three bottam mould Board 30 cm. size with coulter and jointer. / 1
9 tine cultivator – spring loaded / 1
3-furrow disc plough with scrapers. / 1
Ridger. / 1
Rear axle assemblt-gear box steering box assembly of the diesel engine tractor. / 1 set
Note :-
  1. No additional items are required to be provided for the batch/unit working in second shift except the items indicated under the trainees kit and lockers for trainees.
  2. No additional number of items marked (A) are required to be provided for additional number of batches.
  3. The specification of the items in the above list have been given in Metric Units. The items which are available in the market nearest to the specifications as mentioned above, if not available, as prescribed, should be procured. Measuring instruments such as steel rule which are graduated both in English and Metric Units may be procured, if available.

PROPOSED LIST OF TOOLS AND EQUIPMENT FOR 2ND YEAR
Disc harrow 12 disc, 55 cm dia (Traling type). / 1
Offset harrow (Mounted type). / 1
Paddy harrow with 14 knotched disc 55 cm dia., / 1
9 tins cultivator with reversible shovels. / 1
A universal tool bar with different attachment i.e. ridger, shovel, bottom sweep, cultivator, shovels etc. / 1 set
3 bottom furrower / 1
Post hole digger hand operated. / 1
Tractor mounted planker 3 meter long. / 1
Tractor mounted bund former. / 1
Tractor mounted row crop planter with fertilizer attachment (For maize, cotton ground nuts). / 1
Tractor mounted 9 row seed-cum-fertilizer drill. / 1
Tractor mounted 2 row potato planter with fertilizer attachment. / 1
10 x 10 cm centrifugal pump coupled with a 10 Horse Power Electric Motor, / 1
6.25 x 7.5 cm centrifugal pump coupled with 6.5 HP vertical diesel engine. / 1
Tractor mounted 15 x 15 cm centrifugal type irrigation pump. / 1
Irrigation valves and hydrants. / 1
Tractor mounted power sprayer. / 1
Knap sack power sprayer with a 1.7 to 1.9 HP engine. / 1
Knap sack manual sprayer. / 1
Foot operated sprayer. / 1
Rotary duster (Power operated). / 1
Rotary duster (Hand operated). / 1 set
Soil sampling augers. / 22 Nos.
Moisture boxes. / 1
Tractor mounted mower 18 cm size. / 1
Tractor mounted P.T.O. operated self raking reaper with a 150 cm cutting bar. / 1
Tractor front mounted reaper/wind rower with 150 cm cutter bar. / 1
Power wheat thresher beater type, 105 cm.. / 1
Power wheat thresher peg tooth type size 75 cm x 90 cm. / 1
Power operated paddy thresher 5 HP. / 1
Power thresher for ground nut threshing. / 1
Ground nut decorticater paddle operated. / 1
Power maize sheller 5 H.P. / 1
Tractor Operated combine 150 cm size. / 1
Tractor mounted ground nut digger/wind rower. / 1
Tractor mounted potable elevator-digger. / 1
Power cheff/silage cutter with blower. / 1
Power operated grain cleaner cum grader (3 screen oscilating type). / 1
Auger type grain conveyor. / 1
Bag sticher. / 1
Tractor trailor 3-Ton capacity. / 1
Implement loading beam. / 1
General purpose tractor 30 to 40 HP range. / 1 Set
Paddy puddler and cage wheel / 1
Power tiller 8/10 HP diesel with a set of equipment and a trolley. / 2 Nos.
Servicing equipment complete with grease gun high pressure washer, nozzle, compressor unit hydraulic lift, pneumatic type servicing tool kit etc. / 1 set
Grain treater. / 1
Oil 30 HP diesel tractor complete with accessories in working condition / 1
Agriculture land piece for practice. / 10 Acre
Spray painting equipment complete with accessories. / 1 Set
Vulcanising plant complete with accessories / 1
Pressure gauge wall type 0 to 10 kg/cm. 2 range. / 1
Rice huller with 5 HP motor complete with a accessories. / 1
Rice polisher complete with accessories capacity 3 HP. / 1
Post hole digger (Tractor PTO operated) / 1
Seed treating drum. / 1
Sugarcane planter (Semi-automatic). / 1
Tractor operated duster. / 1
Battery operated sprayer. / 1
Knap sack motorized ultra low volume sprayer / 1
Synogas pum / 1
Auger plough / 1
Multicrop thresher with safety device / 1
Mini bus. / 1

Note :-

  1. List of Tools and Equipment for the 1set year is the same as for Tractor Mechanic Trade.
  2. No Tools and Equipment have been included for Allied Trade Training in Welding, Fitting, Turning and Electrician jobs. The existing facilities in the Institute shall be used for this purpose.

ooo