Sl.No / Customers Requirement / Details of Product offered by You / Qty Required
(Indicate MOQ if any) / Code No / Price/Unit
In
1 / S. S. Fasteners / 1 Lot

1. Bolts

Designation: M (x) P (Pitch)> For M&P ref table 2

Thread: ISO metric Thread as per ISO 68

Tolerance: 4h, as per ISO 965

Fastener: Grade A as per ISO 4014

Length(I): Ref attached list (Table 5)

Surface finish: Ra maximum 3.2um

End of fastener: Chamfered as per ISO 4753

Material: SS304 Non-magnetic quality Ultimate tensile strength, minimum: 700 Mpa, yield strenth: 450 Mpa

Qty: Ref table 5

Type of head: Ref table 5

Table 1: Chemical composition.

Austenitic grade / Material
No to AISI / C / Si / Mn / P / S / Cr. / Mo / Ni
1 / 304 / 0.08 / 1.0 / 2.0 / 0.05 / 0.03 / 07.0 to 20.0 / - / 8.0 to 13.0

Table : 2

Thread / M1.6 / M2 / M2.5 / M3 / M4 / M5 / M6 / M8 / M10
Pitch (P) / 0.35 / 0.4 / 0.45 / 0.5 / 0.7 / 0.8 / 1 / 1.25 / 1.50

2. SS 304 Non magnetic quality.

Wire Thread Inserts (Helicoil)

Applicable Standard: SAE MA 3329 and MA 1565 Rev. A

Designation: M______X______(L) As per detail given table -4 (Length to be given in multiples of diameters)

Material: SS 304 as per AS 7245

Hardness: 43 to 50 HRC

Mechanical properties: Ultimate tensile strength> -1375 MPa

Bending : Wire shall withstand, without cracking, bending when tested in accordance with AS7245

Threads: The inserts, when installed in threaded holes conforming to MA 1567 shall from threads conforming to ISO metric screw thread- M profile.

Locking torque: As per table 3, given below.

Surface roughness: 0.2 to 0.4 µm

Surface coating: No coating.

Qty: Ref Table 4

Table-3

Nominal Thread Size / Maximum Locking Torque
N-m / Minimum Breaksway Torque, 15 th cycle
N-m
M2x 0.4 / 0.12 / 0.003
M2.2 x 0.45 / 0.14 / 0.02
M2.5 x 0.45 / 0.22 / 0.06
M3 x 0.5 / 0.44 / 0.10
M3.5 x 0.6 / 0.68 / 0.12
M4 x 0.7 / 0.90 / 0.16
M5 x 0.8 / 1.60 / 0.30
M6 x 1 / 3.00 / 0.40
M7 x 1 / 4.4 / 0.60
M8 x 1.25 / 6.00 / 0.80
M10 x 1.5 / 10.50 / 1.40

Table-4

M / L / Qty
2 / ID & 1.5D / 1000 Each
2.5 / ID & 1.5D / 1000 Each
3 / ID & 1.5D / 1000 & 6000
4 / ID & 1.5D / 1000 & 2000
5 / ID & 1.5D / 500 Each
6 / ID & 1.5D / 1000 Each
8 / ID & 1.5D / 100 Each
10 / ID & 1.5D / 100 Each

3. Heli Tap: For M2, M2.5, M3, M4, M5, M6 wire thread insert

Qty: 4 set each

For M8 and M10 wire thread insert

Qty: 2 set each

Note: Each Tap set consisting of Roughing tap, Finishing tap and Bottoming tap.

4. Wire thread inset inserting Tools for M3, M2, M2.5, M3, M4, M5, M6, M6, & M10 wire thread insert Qty: 2 each

Plain nuts: Ref table 5 SS 304 Nylon lock Nut

Plain Washers: Refer table 5

Applicable Standard: ISO 7089, Product grade A

Tolerances: as per ISO 4759/3

Material: SS304 Non-magnetic quality Ultimate tensile strength, Minimum: 700 MPa yield strength: 450MPa

Magnetic Cleanliness: Non magnetic

Surface Finish: (Before protection)Ra Maximum: 3.2 µm

Approx Dimention

Plain Washers / Dimensions in millimeter
Nominal size
(Thread size,d) / Clerance hole d1 / Outside diameter d2 / Thickness
h
nom.(min) / Max / nom. (min) / min / nom / max / min
M2.5L / 2.7 / 2.84 / 6 / 5.7 / 0.5 / 0.55 / 0.45
M3L / 3.2 / 3.38 / 7 / 6.64 / 0.5 / 0.55 / 0.45
M4L / 4.3 / 4.48 / 9 / 8.64 / 0.8 / 0.9 / 0.7
M5L / 5.3 / 5.48 / 10 / 9.64 / 1 / 1.1 / 0.9
M6L / 6.4 / 6.62 / 12 / 11.57 / 1.6 / 1.8 / 1.4
M8L / 8.4 / 8.62 / 16 / 15.57 / 1.6 / 1.8 / 1.4
M10L / 10.5 / 10.77 / 20 / 19.48 / 2 / 2.2 / 1.8

9. SS 304 Spring Washers (Table 5)

Sl. No / Requirements / Qty
1 / Cheese head screws
M3 x 6L / 1000
M3 x 8L / 1000
M3 x 10L / 1000
M3 x 12L / 1000
M3 x 20L / 1000
M3 x 40L / 500
M4 x 10L / 1000
M4 x 12L / 1000
M4 x 50L / 500
2 / Allen head
M2 x 12L / 1000
M2.5 x 8L / 1000
M3 x 12L / 1000
M3 x 30L / 1000
M4 x 8L / 1000
M4 x 10L / 1000
M4x 12L / 1000
M4 x 16L / 1000
M4 x 40L / 500
M4 x 80L / 200
M5 x 16L / 500
M5 x 40L / 200
M6 x 16L / 500
M6 x 20L / 200
M6x 25L / 200
M6 x 30L / 200
M6 x 35L / 200
M8 x 20L / 200
M8 x 25L / 200
M8 x 30L / 200
M8 x 40L / 200
M10 x 25L / 100
M10 x 30L / 100
M10 x 40L / 100
3 / Hex Head
M4 x 8L / 1000
M4 x 10L / 1000
M4 x 12L / 1000
M4 x 16L / 1000
M4 x 40L / 500
M4 x 80L / 200
M5 x 16L / 500
M5 x 40L / 200
M6 x 16L / 500
M6 x 20L / 200
M6 x 25L / 200
M6 x 25L / 200
M6 x 30L / 200
M6 x 35L / 200
M8 x 20L / 200
M8 x 25L / 200
M8 x 30L / 200
M8 x 40L / 200
4 / CSK
M3 x 12L / 500
M3 x 30L / 500
M4 x 10L / 500
M4 x 12L / 500
M4 x 16L / 500
M4 x 40L / 500
M5 x 25L / 500
M5 x 50L / 200
M6 x 16L / 500
M6 x 35L / 200
Plain Nuts
M2.5L / 1000
M3L / 1000
M4L / 1000
M5L / 1000
M6L / 1000
M8L / 500
Lock Nuts
M2.5L / 1000
M3L / 1000
M4L / 1000
M5L / 1000
M6L / 1000
M8L / 500
M10L / 200
Washer Plain
M2.5L / 1000
M3L / 1000
M4L / 1000
M5L / 1000
M6L / 1000
M8L / 1000
M10L / 500
Spring Washers
M2.5L / 1000
M3L / 1000
M4L / 1000
M5L / 1000
M6L / 1000
M8L / 1000

IMPORTANT PLEASE NOTE: additional terms and conditions.

FOLLOWING IF ANY

1. TEST CERTIFICATE/CALIBRATION CERTIFICATE

2. ALL RELEVENT CATALOGUE SHEET TO BE PROVIDED BY YOU

3. THIRD PARTY INSPECTION

4. LIST OF SPARES

5. EXPORT BOXING