Price List No. 65 Dated May 15, 2011
MARVEL SERIES 8 MARK III, ALL-MECHANICAL, UNIVERSAL,
METAL CUTTING, BANDSAW MACHINE
Specifications and Features
NOTE: Metric specifications represent nearest SI Unit converted from the basic U.S. Customary Unit.
Capacity: Blade at 90°: 18” (457 mm) Horizontal, 22” (558 mm) Vertical
Capacity: Blade at 45° Right: 18” (457 mm) Horizontal, 14.5” (368 mm) Vertical.
Capacity: Blade at 45° Left: 18” (457 mm) Horizontal, 13” (330 mm) Vertical.
Capacity: Blade at 60° Right: 18” (457 mm) Horizontal, 9.7” (246 mm) Vertical.
Capacity: Blade at 60° Left: 18” (457 mm) Horizontal, 7.3” (185 mm) Vertical.
Capacity: Column in 3° forward cant position: 17.5” (445 mm) Horizontal, 22” (558 mm) Vertical;
Speed Range: 50 – 450 fpm (15 – 137 m/min) infinitely variable with inverter drive.
Front Mounted Speed Control: Allows blade speed to be adjusted from operator’s control station.
Feed Range: 0 – 250 lbs. (64 kgf) infinitely variable with control on operator’s panel and Automatic Column Return. Column feed is mechanical with Marvel clutch power feed.
T-Slotted Work Table: Work area 24.25” x 33” (616 mm x 838 mm); Table height 34.5” (876 mm);
Two machined T-slots.
Wheel Diameter: 19” (482 mm), cast iron wheels.
Blade Break/Stall Detection: Standard equipment, shuts off machine in the event of blade breaking or stalling.
Miter Cutting: Column and blade tilt up to 60° right and left of vertical; work always stationary. Manual tilt standard with Sure-Lock and Built-in protractor. Electric Power tilt optional.
Saw Column: Marvel patent pending Quick Change Column is standard on all machines. Allows column to be set either upright or at a 3° forward cant. Column travels on recirculating linear ball bearing rails.
Quick-Action Vise: Maximum opening 18” (457 mm). Jaws can be shifted to either right or left side of blade.
Jaws are 6” (152 mm) high, 12” (305 mm) wide.
Automatic Stops: Adjustable stops can be pre-set to stop advance and return of blade, and also to stop motor at any location within the 18” (457 mm) travel of the blade.
Coolant System: Built In with flood system, available with added optional drop lubrication system (Option Codes
ML1 & ML2). Controlled by on-off selector switch at operator’s station. Tank capacity 21 gallons (79 liters).
Flushing Hose: Washes chips from hard to get at places reducing clean-up time.
Power Chip Brush: Together with blade wipers and flood coolant deep blade teeth free of chips.
Carbide Guide System: Solid carbide post design equipped with Patent Pending Marvel Easy Load Guide Blocks.
Upper and lower guides have preloaded carbide faced back-up blocks to support back edge of blade.
Blade: 15' 4" (4674 mm) long x 1.25" (32 mm) wide, .042" (1.07 mm) thick.
Marvel 8 Mark III – Page 2.
Blade Tension: Blade tension ratchet stops automatically at factory pre-set, 40,000 psi (A compressed air
connection is required for standard operation, 5 CFM, 80 psi minimum)
Motors: Main; 5 H.P. (3.75 kW), 1800 RPM, totally enclosed fan cooled. Coolant Pump; 1/8 H.P. (.1 kW) totally
enclosed motor-built-in integrally. Available voltage: 208 volt, 240 volt,480 volt or 575 volt, 3 phase, 60 Hz. If
ordering 575 volt the machine will be wired for 460 volt, a 575 to 460 volt transformer will be provided with the
machine. A qualified electrician will be needed to install the transformer between the power supply and the
machine. Specific voltage must be specified when ordering.
Controls: IEC fused disconnect switch and magnetic motor starters, with overload and low-voltage protection.
Disconnect is NFPA79 compliant. DC Power supply provides low voltage control (24 Volts) to all push buttons at
operator’s control panel and machine lighting circuits. PLC control and components mounted in moisture proof
NEMA 12 compartment. Electrical Panel is UL labeled.
Price: Complete machine ready to operate, including motors and controls……………………………$ 24,535.00
M3M: Powered Column Tilt: Provides powered tilting of saw column up to 60° to both right and left sides. Tilt control switch is located on the operator’s control panel (must be specified on original order).
Price: (Must be specified on original machine order)...... $ 2,500.00
M6: High Column: Column 6” (150 mm) longer than standard, providing increased vertical capacity to 28” (711 mm) at vertical position. High frame machines require a 16’ 4” (498 mm) blade. Note: Includes Option Code 8/M3M Powered Column Tilt. Capacity: Blade at 90°: 18” (457 mm) Horizontal, 28” (711 mm) Vertical; Capacity: Blade at 45° Right: 18” (457 mm) Horizontal, 18.75” (476 mm) Vertical; Capacity: Blade at 45° Left: 18” (457 mm) Horizontal, 17.3” (439 mm) Vertical; Capacity: Blade at 60° Right: 18” (457 mm) Horizontal, 12.5” (317 mm) Vertical; Capacity: Blade at 60° Left: 18” (457 mm) Horizontal, 10.25” (260 mm) Vertical.
Price: (Must be specified on original machine order)…………………………………………………………..$ 4,755.00
M7: High Jaws (jaws only): 10” high x 12” wide (254 mm x 305 mm, in place of standard jaws provided with machine. Jaws use same clamping hardware provided with machine. Does not permit miter cutting.
Price: Set (Must be specified on original machine order)...... $ 525.00
ML1: Mist Lube- Manual: Drop Lubrication System. (Requires compressed air connection)
Price: (Must be specified on original machine order)……………………………………………………………$ 1,110.00
ML2: Mist Lube- Automatic: Drop Lubrication System. (Requires compressed air connection)
Price: (Must be specified on original machine order)……………………………………………………………$ 1,975.00
SUPPLEMENTARY MATERIAL HANDLING EQUIPMENT
E4: Second Standard Vise- COMPLETE: Standard set including 6” high x 12” wide (152mm x 305mm) jaws and clamping hardware. PERMITS MITER CUTTING.
Price: Per Set (Must be specified on original machine order)………………………………………………..…$ 765.00
E5: High Jaw Vise – COMPLETE: High jaw set including 10” high x 12” wide (542mm x 305mm) jaws and clamping hardware. DOES NOT PERMIT MITER CUTTING.
Price: Per Set (Must be specified on original machine order)…………………………………………………..$ 1,135.00
E6: High Jaws (jaws only): 10” high x 12” wide (254mm x 305mm). Will interchange with standard 6” high x 12” wide (152mm x 305mm. Jaws use same clamping hardware provided with machine. DOES NOT PREMIT MITER CUTTING.
Price: Per Set (Must be specified on original machine order)…………………………………………………..$ 855.00
E8: Length Gauge: For gauging work pieces from .062” to 10.5” (1.6 mm x 267 mm) long. Fits T-slots in machine table.
Price: (Must be specified on original machine order)…..……………………………………………………….$ 120.00
E10: Length Gauge: Manual light duty length gauge. Securely mounts on roller conveyor. Gauging limited by length of roller conveyor.
Price: (Must be specified on original machine order)…..……………………………………………………….$ 165.00
Marvel 8 Mark III – Page 3.
E11: Coolant Pan: Will fit F055 and X055 roller conveyors. Collects and returns coolant back to machine. Includes pan, V-trough, and hangers.
Price: (Must be specified on original machine order)…..……………………………………………………….$ 280.00
E12: Eccentric Lift Roller: May be mounted on roller conveyor for either load or discharge sides; manually operated to raise roller and material slightly above machine table. Lift capacity 1,000 pounds.
Price:...... $ 175.00
E13: Additional Rollers: For added support; can be installed between standard rollers.
Price: (Must be specified on original machine order)...... $ 50.00
E14: Air Operated Ratchet Nut: Only for use with standard or high jaw vise supplied with machine.
*Air supply not included.
Price: (Must be specified on original machine order)…...... ……………………………………………..$ 995.00
E15: 45° High Jaw Vise – COMPLETE: Set includes One Front Jaw and One Rear Jaw, both mitered 45° 10” high x 12” wide (254mm x 305mm) and clamping hardware. PERMITS MITER CUTTING.
Price: (Must be specified on original machine order)…..……………………………………………………….$ 1,230.00
DRO: Digital Tilt Readout – Electronic digital display mounted on the saw column and visible from the operator’s control station. Displays the angle of the column tilt from 0 to 60 degrees left and right in increments down to one half degree. Readout is tied into low voltage control power supply.
Price: (Must be specified on original machine order)…..……………………………………………………….$ 950.00
MATERIAL HANDLING EQUIPMENT
8/F055: First Section Dead Roller Conveyor: 5’0” (1524 mm) LONG, with five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, two stands, one end stop, and mounting bracket. Used as first section on either loading or discharge side of machine.
Price: (Must be specified on original machine order)…..…..……………………………………………………$ 1,050.00
8/X055: Extension Dead Roller Conveyor 5’ 0” (1524 mm) LONG, five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, one stand, attached to 8/F055, for use on either loading or discharge side of machine.
Price: (Must be specified on original machine order)……………………………………………………………$ 780.00
SP1118: First Section Dead Roller Conveyor - Free Standing: 5’ 0” (1524 mm) long with five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” centers, two stands, and one end stop.
Price: (Must be specified on original machine order)……………………………………………………………$ 1,250.00
SP1104: Extension Dead Roller Conveyor - Free Standing: 5’ 0” (1524 mm) long with five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” centers, with two stands. To be used as an extension to the First Section Free Standing Conveyor.
Price: (Must be specified on original machine order)……………………………………………………………$ 1,100.00
NOTE: MAXIMUM LOAD CAPACITY 800 POUNDS/FOOT.
SP1040: First Section Dead Roller Conveyor with Manual Length Gauge: 10’ 0” (3048 mm) long, ten ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, includes Dead Stop, Tilting Type Gauge, Manually operated; runs along tape and rail fastened to front side of Roller Table. Gauge can be locked in place for gauging, and tilted out of the way to permit work passage. Indicate Left or Right configuration.
Price: (Must be specified on original machine order)……………………………………………………………$ 4,250.00
SP1097: Extension Dead Roller Conveyor with Gauge Rail: 5’ 0” (1524 mm) long, five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, similar to X055, but also equipped with gauge rail and measuring tape extensions. For use with and as an EXTENSION to SP1040. Indicate Left or Right configuration.
Price: (Must be specified on original machine order)……………………………………………………………$ 2,450.00
STANDARD MACHINE COLOR: Machine Tool Gray
COMPRESSED AIR REQUIRED: 5 cfm, 80 psi minimum
Marvel 8 Mark III – Page 3.
TERMS OF SALE
All prices contained herein are subject to change without notice and are further subject to an increase in price equal to the amount of any Federal, State, or Local Tax that may be imposed. MARVEL also reserves the right to make design changes and/or modifications on machines without prior notice.
Delivery dates given are estimates only, based on prevailing conditions and available information, and any special requirements that may affect the order are subject to the conditions and contingencies beyond our control.
10% down payment is due with purchase order. A 35% restocking charge will be assessed for all cancelled orders.
No officer, employee, representative, or agent is authorized to bind the company to acceptance of any order in the field. All orders are subject to acceptance by the company at its home office in Oshkosh, Wisconsin.
START-UP SUPPLIES (included with machine at no extra cost):
A. BANDSAW BLADE: One (1) high-speed welded-edge blade.
B. MANUFACTURER’S TECHNICAL DATA: Two (2) sets consisting of parts listed, operating and maintenance instructions, installation plan, wiring, elementary electric and hydraulic diagrams, and electrical and hydraulic component list.
C. 2 GALLONS OF CUTTING FLUID MIX
WARRANTY: MARVEL MANUFACTURING COMPANY, INC. warrants to the original user for the period of two (2) years from date of factory shipment that every new MARVEL metal sawing machine is free from defect in material or workmanship. During that period, we will at our option, repair or replace any part which, upon examination, we find defective. This warranty will not apply to alterations or modifications made upon MARVEL metal sawing machines without our written consent, or to machines that have been subject to willful abuse.
All items quoted here are designed, engineered, and manufactured by Marvel Manufacturing Company, Inc.
Marvel Manufacturing Company, Inc. • 3501 Marvel Drive • Oshkosh, WI 54902 • U.S.A.
Phone: (920) 236-7200 (800) 472-9464 Fax: (920) 236-4156
www.marvelsaws.com
Sales & Service Centers/Warehouses
OSHKOSH, WI • 1 800 472-9464 • FAX: 1 920 236-4156
FT. WORTH, TX • 1 817 535-2183 • FAX: 1 817 531-1163
LONGVIEW, WA • 1 360 575-9917 • FAX: 1 360 575-9706
BIRMINGHAM, AL • 1 205 916-2828 • FAX: 1 205 916-2827
District Sales Managers and Technical Specialists in Major Cities.