ALLPRO GOLD™ White
ALLPRO® Corporation
Brandon, FL 33511 / AP4950 - 16685
June, 2002
Description / ALLPRO GOLD™ Acrylic Urethane Sealant White offers advanced waterborne performance with a lifetime warranty. Ideal for the quality conscious builder because it withstands high shear movement and adheres to the most difficult of surfaces including hardboard siding, pressure treated lumber, bare aluminum, glass and concrete. Withstands 500% elongation with 98% memory and meets the performance requirements of Federal Specification TT-S-00230, Type II, Class A and ASTM C-920 Class 25. Also meets ASTM C-834.
Prominent Features /
- Advanced latex technology
- 500% elongation & 98% memory
- Superb flexibility - withstands high shear movement
- Excellent for use with crown molding and expansion & control joints
- Outstanding adhesion to difficult surfaces
- Ideal for hardboard siding, pressure treated lumber, glass, bare aluminum & concrete
- Easy application & cleanup
- Vacuumized to ensure maximum in durability and gunability
Uses / For use on wood, metal, brick, masonry, concrete, marble, porcelain, glass and ceramic tile. May be used to bond similar and dissimilar surfaces; such as selective expansion & control joints. Excellent for exterior wood siding, interior crown molding and trim. Ideal for window and door frames, thresholds, woodwork, skylights, eaves, showers, tubs, sinks and vents. Also use around plumbing, for RV use and aboard boats above water line.
Limitations / Not intended for underwater use. Do not apply when rain is expected. Not intended for food contact surfaces. Allow new concrete to cure for 30 days before applying material. Keep from freezing.
Surface Preparation / Surface must be clean, dry and free from dirt, dust, grease, oil, mildew, wax, loose paint or loose wallcovering. When re-caulking, remove all old caulking compound. Lightly sand pre-primed hardboard siding with fine sandpaper to remove any unwanted surface blocking additives that might interfere with the adhesion of this sealant.
Application / Apply caulk at surface temperature of at least 50ºF (10ºC) with a conventional caulk gun, to primed or unprimed clean surface. Smooth bead with moistened brush or cloth. For best results, cured beads should be at least 1/8" wide, but not more than 1/2" wide. For joints deeper than 1/2", use back-up filler material (backer-rod) that is 1/8" larger in diameter than the width of the joint to allow for compression
Clean Up / Clean up immediately after use with warm, soapy water.
Disposal / Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning possible reuse or disposal of unused solvent-containing adhesives and/or sealants.
Limited Warranty / If, when applied as directed, this material peels, cracks or separates within 35 years after application, it will be replaced without charge upon presentation of proof of purchase and used cartridge. This limited warranty only applies to residential use and damages including consequential damage and other remedies are excluded. No other warranties apply, including fitness for particular purpose.
Caution / Technical Information
Do not take internally. WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN.
NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use.
FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.
Material Safety Data Sheets (MSDS) available upon request. Similar information for solvents and other chemicals used with ALLPRO products should be obtained from you supplier(s). When solvents are used, proper safety precautions must be observed.
Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511
Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable. / Packaging: Standard packaging - 10.1* fluid ounce
plastic cartridges. ( * Packaging in mid-late 2002 changing from
10.5 fl. oz. to 10.1 fl. oz. fill)
Color: White
Data below for white: 16685
Weight per Gallon: 11.3 ± 0.2 lbs.
Specific Gravity: 1.36
% Solids by Weight: 76.3% ± 1%
% Solids by Volume: 64.9% ± 1%
pH (when packaged): 8.1 ± 0.2
Viscosity: Smooth thixotropic paste
Extrudability (ASTM C731): 2 g/s, minimum
Spreading Rate: Approximately 43 linear feet @ bead
of 3/16" x 3/16"
Dry Time - Tack Free: 1 hour at 73°F & 40% R.H.
Dry Hard: Approximately 4 - 6 hours. Paintable with
premium quality, non-flat latex/acrylic when dry.
Full cure - approximately 21 days.
Service temp. range: -30°F to 180°F(-34°C to 82°C)
Flexibility (1/4" slab on aluminum @ -15°F,
ASTM C734): Pass
Ultimate Elongation(1/8" cured slab, ASTM -D412):
500% Minimum
Hardness (Shore A Durometer, ASTM D2240): 30 ± 5
Slump (ASTM D2202): Zero
Flash Point: Nonflammable, waterborne
Odor: Very low, ammonia-like
Storage: Inside, between 32°F & 100°F(0°C & 38°C)
Shelf Life: 2 years minimum
Freeze/Thaw (ASTM C731): Passes 5 cycles
Vehicle: Premium Urethane- Acrylic
Volatile Portion (Exempt): Water
Volatile Portion (Non-Exempt): Ethylene Glycol /
Aromatic Solvent
Air Quality Data: VOC 51.3 g/l (0.45 lb./gal.)
Analysis:
Urethane Acrylic Resin (CAS unknown)
White Mineral Oil (Petroleum) (8042-47-50)
Calcium Carbonate (471-34-1)
Ethylene Glycol (107-21-1)
Formaldehyde (50-00-0)
Contents Partially Unknown
Water (7732-18-5)