APPENDIX C - DATA SHEETS

UNINTERRUPTIBLE POWER SUPPLIES

PROJECT TITLE (P) / DOCUMENT REFERENCE (P)
PROJECT REFERENCE NUMBER (P) / REVISION (P)
PROJECT LOCATION (P) / DATE (P)
UPS SUPPLIER (P/S) / REFERENCE DRAWINGS INCLUDED (Y/N) (P)

WIMES 3.07Page 1

* - indicates Purchaser’s default requirement.

3.0 OPERATING ENVIRONMENT AND SITE DETAILS

1 / Operating Environment (P)
Site Location
Inland/coastal
Rural/urban/industrial
UPS Location ()
Inside (heated)
Inside (unheated)
Other (specify)
EMC Environment ()
1st environment – C1
1st environment – C2
2nd environment – C3
2 / Deviations From Normal Service Conditions (P)
3 / Unusual Environmental Service Conditions (P)

4.0 ELECTRICAL SUPPLY AND LOAD CHARACTERISTICS

4.1 Electrical Supply Characteristics

1 / Voltage, Frequency and No. of Phases (P)
1 / Voltage and Frequency Variations (+/- %) (P)1
Voltage variation
Frequency variation

1 –If the UPS will be supplied from a diesel generator, the relevant voltage and frequency values shall be specified here.

4.2 Load Characteristics

1 / Type of Load () (P)
PLC, SCADA,
instrumentation
Valve actuator
Other (specify)
PLC, SCADA, Instrumentation
Supply Details
(V, Hz, Ph, tolerances)
Current (A)
Power factor
Non Linear Load (Y/N)
Crest Factor
Valve Actuator
Supply Details
(V, Hz, Ph, tolerances)
Current Details (A)
Nominal operating
Maximum operating
Starting
Power Factor
Other Load Type(s) (Specify Details)

5.0 PERFORMANCE SPECIFICATION

5.1 General

1 / Service Life (Years) (P)

5.3 Electrical Characteristics

5.3.1 Input Characteristics

1 / Input Characteristics (P/S)
a / Rated input voltage (V)
b / Rated input voltage tolerance (%)
c / Rated input frequency (Hz)
d / Rated input frequency tolerance (%)
e / Number of phases
f / Rated input current (A)
g / Maximum continuous current (A)
h / THD (current) at rated input current (%)
i / Input power factor

5.3.2 Output Characteristics

1 / Output Characteristics (P/S)
a / Rated output voltage (V)
b / Rated output voltage tolerance (%)
c / Rated output frequency (Hz)
d / Rated output frequency tolerance (%)
e / Number of phases
f / Rated output apparent power (VA)
g / Rated output active power (linear load) (W)
h / Rated output active power (non-linear load) (W)
i / Total voltage distortion (linear load) (%)
j / Total voltage distortion (non-linear load) (%)
k / Output fault clearing capability
l / Overload capability
m / Range of load power factor permitted

5.3.3 Batter and Battery Charger Characteristics

1 / Battery/Battery Charger Characteristics (P/S)
a / Battery rating (Ah)
b / Cell voltage (V)
b / Cell rating (Ah)
c / Stored energy time at rated load (min)
d / Restored energy time
(to 90 % charge) (min)

5.4 Noise

1 / Noise Levels (dB(A)) (P/S)
Maximum (70*) (P)
Actual (S)

5.5 Life Cycle Costs

5.5.1 Efficiency

1 / Efficiency (P/S)
Minimum (90*) (P)
Actual (S)

5.5.2 Service Lives and Costs of Components

1 / Expected Service Lives of Components (P/S)
Component (P) / Life (x 103 hrs) (S)
Rectifier/charger
Battery
Inverter
2 / Costs of Components (£)/Time Required to Replace Components (mins) (S)
Component (specify) / Cost / Time
Rectifier/charger
Battery
Inverter

5.5.4 Availability

1 / Availability (P/S)
Minimum (99.99*) (P)
Actual (S)

6.0 DESIGN SPECIFICATION

6.1 General

6.1.1 General

1 / UPS Model Number (S)
4 / IP Rating (IP 21*) (P)
5 / Galvanic Isolation (P)
Required (Y/N)
5 / Degree of Galvanic Isolation Required (P)
6 / Maintenance Bypass Facility Required (Y/N) (P)

6.1.2 Weights and Lifting Arrangements

1 / Weights (kg) (S)
Weight of UPS
Heaviest maintenance lift

6.1.4 O & M Manuals

1 / Type Required/Provided() (P/S)
Purchaser’s standard
Supplier’s standard

6.2 Input Protection

1 / Type of Protective Device (S)
1 / Rating of Protective Device (A) (S)

6.3 Rectifier/Battery Charger

2 / Charging Voltage to Vary with Ambient Temperature (Y/N) (P)
3 / Charging Voltage to Vary with Charge on Battery (Y/N) (P)

6.4 Battery

2 / Battery Design Life at 20oC (Years) (P/S)
2 / Battery to comply with BS6920 (Y/N) (P/S)

6.4 Battery (contd.)

3 / Battery Details (S)
a / Cell/Monoblock Characteristics
Voltage (V)
Nominal capacity (Ah)
Cut-off voltage (V)
b / Cell/Monoblock Configuration
Serial String Configurations
Number of cells
Parallel String Configurations
Number of serial strings
Number of cells per string
c / Battery Characteristics
Voltage (V)
Nominal Capacity (Ah)
6 / Condition Monitoring System (P)
Required (Y/N)
Monitored Parameters () (P)
Battery temperature
Float current
Float voltage
AC/DC resistance
On-line discharge characteristics
Other (specify)
7 / Location () (S)
In the UPS enclosure
In a separate enclosure
In separate racks
Other (specify)

6.5 Configuration and Protection of Outgoing Circuits

1 / Configuration and Protection of Outgoing Circuits (P/S)

6.6 Communications

1 / Type of Communications Required/ Provided (P/S)

6.7 Status Indications, Alarms and Telemetry Outputs

1 / Status Indications Required/Provided () (P/S)
Load on inverter
Load on battery
Battery charge remaining
1 / Alarms Required/Provided () (P/S)
Load on bypass
Overload
Low/high output voltage
Inverter fault
Battery charger fault
Low battery voltage
Over temperature
2 / Telemetry Outputs Required/Provided2() (P/S)
Common fault
Load on inverter
Load on bypass

2 – Indicate whether telemetry output is via a serial data connection (SDC) or volt free change-over contacts (VFC)

ISSUE 4NOVEMBER 2015

WIMES 3.07Page 1

APPENDIX D – SUPPLIER’S SUPPLEMENTARY DATA SHEET INFORMATION

Clause / Supplementary Information

ISSUE 4NOVEMBER 2015