Bill of quantitiesPANDOMO® FloorPlus
PANDOMO® K1 Design levelling compound, white

SUBSTRATE PREPARATION:

Item ) / Mechanically roughen or wire-brush the substrate, as well as remove all dust and debris to ensure a stable subfloor.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Seal any non-moving joints or cracks with epoxy resin to reinstate structural integrity. Make slots across the crack at a distance of 25 cm by using a cutting disk, insert steel nails and seal with ARDEX FB casting resin. After having poured the sealing compoundonto the substrate, sprinkle with smoothing compound powder. Comply fully with the manufacturer’s technical specifications.
...... m² Labour cost / € ......
Material cost/other cost / € ......
lfm / € ...... / € ......
Option:
Level the primed concrete floor with ARDEX PANDOMO K 1, layer thickness...... mm.
Apply at least 5 mm of ARDEX PANDOMO K 1. Maximum layer thickness is 10 mm. Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Apply PANDOMO PR-PRIMER to the cleaned sand/ cement screed in two operations:
1. Dilute PANDOMO PR 1:3 with water, apply the primer to the substrate using a broom, and wait until dried. Brush out any puddles & allow to fully dry.
2. Apply PANDOMO PR diluted 1:1 with water to the substrate using a broom and wait until dried. Brush out any puddles.
Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Option:
Item ) / Install a prime coat onto the cleaned sand/cement screed using ARDEX EP 2000 Multifunctional Epoxy Resin. The prime coat is applied using a short pileroller, and sanded when still wet using dry ARDEX QS Quartz sand with a grain size of 0.3-0.6 mm. Comply fully with the manufacturer’s technical specifications.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Install expansion joint profiles.
Make sure to comply with the technical specifications provided by the manufacturer.
...... lfm Labour cost / € ......
Material cost/other cost / € ......
lfm / € ...... / € ......
Item ) / Install edge protection profiles
Make sure to comply with the technical specifications provided by the manufacturer.
...... lfm Labour cost / € ......
Material cost/other cost / € ......
lfm / € ...... / € ......

APPLICATION OF THE SMOOTHING COMPOUND:

Item ) / Provide the primed sand/cement screed with a smoothing layer of PANDOMO K 1 with ARDURAPID effect, white, in the FloorPlus solution, minimum layer thickness is 5 mm. The special aggregate PANDOMO HG is sprinkled into the freshly laid surface. Use a spike blade knife to apply the smoothing compound, and smoothen using a long handle smoothing trowel. Comply fully with the manufacturer’s technical specifications.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Any further mm
Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Providethe primed cementitious sand/screed with a smoothing layer of PANDOMO K 1 withARDURAPID effect, tinted, in the FloorPlus solution, minimum layer thickness is 5 mm. The special aggregate PANDOMO HG is sprinkled into the freshly laid surface. Use a spike blade knife to apply the smoothing compound, and smoothen using a long handle smoothing trowel. Comply fully with the manufacturer’s technical specifications.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Any further mm
Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Option:
Improve PANDOMO K 1 with ARDEX E 25 artificial resin dispersion. Make sure to comply with the technical specifications provided by the manufacturer.
Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......

PANDOMO® FloorPlus - Treatment

Item ) / Polish the PANDOMO K 1 smoothing compound surface in three operations using a suitable grinder (e.g. Trio, made by Lägler). Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Apply PANDOMO SL stone oil impregnation agent. After 12 hours, apply the second coat of PANDOMO SL. Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Apply PANDOMODMC dispersion treatment using a lambswool wiper. After approx. 60 minutes, apply the second load of PANDOMODMC. Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......
Item ) / Option:
Apply PANDOMO WP Floor polish with a wiper mop. Make sure to comply with the technical specifications provided by the manufacturer.
...... m² Labour cost / € ......
Material cost/other cost / € ......
m² / € ...... / € ......